Re: Rebbot after upgrade to v2.11.0-568-gf1c1aea puts me to the ddb prompt in i386

[Sepherosa Ziehau <sepherosa@xxxxxxxxx>]

On Thu, Jul 21, 2011 at 6:47 PM, Siju George <sgeorge.ml@gmail.com> wrote:
> On Thu, Jul 21, 2011 at 3:13 PM, Sepherosa Ziehau <sepherosa@gmail.com> wrote:
>>
>>
>> Hmm, make sure that you have done a full buildkernel instead of quickkernel
>>
>
> Yes I always do a full buildkernel :-)
>
>>Please post following information:
>>acpidump -t
>>
>
> dfly-bkpsrv# acpidump -t
> /*
>  RSD PTR: OEM=ACPIAM, ACPI_Rev=1.0x (0)
>        RSDT=0x7dfd0000, cksum=188
>  */
> /*
>  RSDT: Length=52, Revision=1, Checksum=141,
>        OEMID=A M I, OEM Table ID=OEMRSDT, OEM Revision=0x1000624,
>        Creator ID=MSFT, Creator Revision=0x97
>        Entries={ 0x7dfd0200, 0x7dfd0390, 0x7dfd03f0, 0x7dfde040 }
>  */
> /*
>  FACP: Length=132, Revision=2, Checksum=82,
>        OEMID=A M I, OEM Table ID=OEMFACP, OEM Revision=0x1000624,
>        Creator ID=MSFT, Creator Revision=0x97
>        FACS=0x7dfde000, DSDT=0x7dfd0430
>        INT_MODEL=APIC
>        Preferred_PM_Profile=Unspecified (0)
>        SCI_INT=9
>        SMI_CMD=0xb0, ACPI_ENABLE=0xe1, ACPI_DISABLE=0x1e, S4BIOS_REQ=0x0
>        PSTATE_CNT=0xe2
>        PM1a_EVT_BLK=0x800-0x803
>        PM1a_CNT_BLK=0x804-0x805
>        PM2_CNT_BLK=0x880-0x880
>        PM_TMR_BLK=0x808-0x80b
>        GPE0_BLK=0x820-0x827
>        P_LVL2_LAT=101 us, P_LVL3_LAT=1001 us
>        FLUSH_SIZE=1024, FLUSH_STRIDE=16
>        DUTY_OFFSET=4, DUTY_WIDTH=3
>        DAY_ALRM=13, MON_ALRM=0, CENTURY=0
>        IAPC_BOOT_ARCH={LEGACY_DEV,8042}
>        Flags={WBINVD,PROC_C1,SLP_BUTTON,RTC_S4,TMR_VAL_EXT}
>  */
> /*
>  FACS: Length=64, HwSig=0x00000000, Firm_Wake_Vec=0x00000000
>        Global_Lock=
>        Flags=
>        Version=1
>  */
> /*
>  DSDT: Length=14964, Revision=1, Checksum=105,
>        OEMID=1ABZR, OEM Table ID=1ABZRB49, OEM Revision=0xb49,
>        Creator ID=INTL, Creator Revision=0x2002026
>  */
> /*
>  APIC: Length=92, Revision=1, Checksum=174,
>        OEMID=A M I, OEM Table ID=OEMAPIC, OEM Revision=0x1000624,
>        Creator ID=MSFT, Creator Revision=0x97
>        Local APIC ADDR=0xfee00000
>        Flags={PC-AT}
>
>        Type=Local APIC
>        ACPI CPU=1
>        Flags={ENABLED}
>        APIC ID=0
>
>        Type=Local APIC
>        ACPI CPU=2
>        Flags={DISABLED}
>        APIC ID=129
>
>        Type=IO APIC
>        APIC ID=1
>        INT BASE=0
>        ADDR=0x00000000fec00000
>
>        Type=INT Override
>        BUS=0
>        IRQ=0
>        INTR=2
>        Flags={Polarity=conforming, Trigger=conforming}
>
>        Type=INT Override
>        BUS=0
>        IRQ=9
>        INTR=21
>        Flags={Polarity=active-lo, Trigger=level}
>  */
> /*
>  MCFG: Length=60, Revision=1, Checksum=118,
>        OEMID=A M I, OEM Table ID=OEMMCFG, OEM Revision=0x1000624,
>        Creator ID=MSFT, Creator Revision=0x97
>
>        Base Address= 0x00000000e0000000
>        Segment Group= 0x0000
>        Start Bus= 0
>        End Bus= 255
>  */
> acpidump: RSDT entry 3 (sig OEMB) is corrupt
> dfly-bkpsrv#
>
>

Please try this patch:
http://leaf.dragonflybsd.org/~sephe/0001-ioapic-Don-t-do-the-default-IRQ-configure-if-it-is-m.patch

Best Regards,
sephe

-- 
Tomorrow Will Never Die