DragonFly users List (threaded) for 2011-07
[
Date Prev][
Date Next]
[
Thread Prev][
Thread Next]
[
Date Index][
Thread Index]
Re: Rebbot after upgrade to v2.11.0-568-gf1c1aea puts me to the ddb prompt in i386
On Fri, Jul 22, 2011 at 10:12 AM, Sepherosa Ziehau <sepherosa@gmail.com> wrote:
> On Thu, Jul 21, 2011 at 6:47 PM, Siju George <sgeorge.ml@gmail.com> wrote:
>> On Thu, Jul 21, 2011 at 3:13 PM, Sepherosa Ziehau <sepherosa@gmail.com> wrote:
>>>
>>>
>>> Hmm, make sure that you have done a full buildkernel instead of quickkernel
>>>
>>
>> Yes I always do a full buildkernel :-)
>>
>>>Please post following information:
>>>acpidump -t
>>>
>>
>> dfly-bkpsrv# acpidump -t
>> /*
>> RSD PTR: OEM=ACPIAM, ACPI_Rev=1.0x (0)
>> RSDT=0x7dfd0000, cksum=188
>> */
>> /*
>> RSDT: Length=52, Revision=1, Checksum=141,
>> OEMID=A M I, OEM Table ID=OEMRSDT, OEM Revision=0x1000624,
>> Creator ID=MSFT, Creator Revision=0x97
>> Entries={ 0x7dfd0200, 0x7dfd0390, 0x7dfd03f0, 0x7dfde040 }
>> */
>> /*
>> FACP: Length=132, Revision=2, Checksum=82,
>> OEMID=A M I, OEM Table ID=OEMFACP, OEM Revision=0x1000624,
>> Creator ID=MSFT, Creator Revision=0x97
>> FACS=0x7dfde000, DSDT=0x7dfd0430
>> INT_MODEL=APIC
>> Preferred_PM_Profile=Unspecified (0)
>> SCI_INT=9
>> SMI_CMD=0xb0, ACPI_ENABLE=0xe1, ACPI_DISABLE=0x1e, S4BIOS_REQ=0x0
>> PSTATE_CNT=0xe2
>> PM1a_EVT_BLK=0x800-0x803
>> PM1a_CNT_BLK=0x804-0x805
>> PM2_CNT_BLK=0x880-0x880
>> PM_TMR_BLK=0x808-0x80b
>> GPE0_BLK=0x820-0x827
>> P_LVL2_LAT=101 us, P_LVL3_LAT=1001 us
>> FLUSH_SIZE=1024, FLUSH_STRIDE=16
>> DUTY_OFFSET=4, DUTY_WIDTH=3
>> DAY_ALRM=13, MON_ALRM=0, CENTURY=0
>> IAPC_BOOT_ARCH={LEGACY_DEV,8042}
>> Flags={WBINVD,PROC_C1,SLP_BUTTON,RTC_S4,TMR_VAL_EXT}
>> */
>> /*
>> FACS: Length=64, HwSig=0x00000000, Firm_Wake_Vec=0x00000000
>> Global_Lock=
>> Flags=
>> Version=1
>> */
>> /*
>> DSDT: Length=14964, Revision=1, Checksum=105,
>> OEMID=1ABZR, OEM Table ID=1ABZRB49, OEM Revision=0xb49,
>> Creator ID=INTL, Creator Revision=0x2002026
>> */
>> /*
>> APIC: Length=92, Revision=1, Checksum=174,
>> OEMID=A M I, OEM Table ID=OEMAPIC, OEM Revision=0x1000624,
>> Creator ID=MSFT, Creator Revision=0x97
>> Local APIC ADDR=0xfee00000
>> Flags={PC-AT}
>>
>> Type=Local APIC
>> ACPI CPU=1
>> Flags={ENABLED}
>> APIC ID=0
>>
>> Type=Local APIC
>> ACPI CPU=2
>> Flags={DISABLED}
>> APIC ID=129
>>
>> Type=IO APIC
>> APIC ID=1
>> INT BASE=0
>> ADDR=0x00000000fec00000
>>
>> Type=INT Override
>> BUS=0
>> IRQ=0
>> INTR=2
>> Flags={Polarity=conforming, Trigger=conforming}
>>
>> Type=INT Override
>> BUS=0
>> IRQ=9
>> INTR=21
>> Flags={Polarity=active-lo, Trigger=level}
>> */
>> /*
>> MCFG: Length=60, Revision=1, Checksum=118,
>> OEMID=A M I, OEM Table ID=OEMMCFG, OEM Revision=0x1000624,
>> Creator ID=MSFT, Creator Revision=0x97
>>
>> Base Address= 0x00000000e0000000
>> Segment Group= 0x0000
>> Start Bus= 0
>> End Bus= 255
>> */
>> acpidump: RSDT entry 3 (sig OEMB) is corrupt
>> dfly-bkpsrv#
>>
>>
>
> Please try this patch:
> http://leaf.dragonflybsd.org/~sephe/0001-ioapic-Don-t-do-the-default-IRQ-configure-if-it-is-m.patch
In addition to the above patch, apply following patch too:
http://leaf.dragonflybsd.org/~sephe/0002-ioapic-Disable-unused-GSI-instead-of-leaving-it-in-u.patch
Best Regards,
sephe
--
Tomorrow Will Never Die
[
Date Prev][
Date Next]
[
Thread Prev][
Thread Next]
[
Date Index][
Thread Index]