DragonFly users List (threaded) for 2006-05
[
Date Prev][
Date Next]
[
Thread Prev][
Thread Next]
[
Date Index][
Thread Index]
KDE: volume setting doesn't work
Hi,
after having discussed this issue on #dragonflybsd with moderate success, I
ask for help from the broader audience of this list.
My problem: KDE's volume setting app, KMix, doesn't seem to find a sound/mixer
device, I don't get a throttle to control sound, I get only an empty listbox
for the "Current mixer:". I can play sounds with Noatun and Kaboodle, though.
When I use a not-arts-based sound app, like xmms (OSS Driver 1.2.10) or
Amarok (xine), I can set the sound volume. I can set the sound volume with
the cli app aumix, too.
Under Linux (ALSA), I can use my sound chip with the intel_8x0/ac97/snd_hda
drivers.
This is my setup:
I load the snd_ich driver in /boot/loader.conf:
snd_ich_load="YES"
I set this two sysctl options before starting KDE:
sysctl hw.snd.maxautovchans=8
sysctl hw.snd.pcm0.vchans=8
My card is recognized (from dmesg):
[..]
pcm0: <Intel ICH6 (82801FB)> port 0x9c00-0x9c3f,0x9800-0x98ff mem
0xdffff400-0xdffff4ff,0xdffff800-0xdffff9ff irq 5 at device 30.2 on pci0
pcm0: <Avance Logic ALC650 AC97 Codec>
[..]
I've attached my dmesg output and my /var/log/messages to this email, please
have a look at them, too.
This ist the output of /dev/sndstat (cat):
FreeBSD Audio Driver (newpcm)
Installed devices:
pcm0: <Intel ICH6 (82801FB)> at io 0xdffff800, 0xdffff400 irq 5 bufsz 16384
(1p/1r/8v channels duplex)
This are the device entries (ls -al /dev | grep "30,"):
SchlesisNB# ls -al | grep "30,"
crw-rw-rw- 1 root wheel 30, 4 May 9 12:00 audio0.0
crw-rw-rw- 1 root wheel 30, 0x00010004 May 1 19:59 audio0.1
crw-rw-rw- 1 root wheel 30, 0x00020004 May 1 19:59 audio0.2
crw-rw-rw- 1 root wheel 30, 0x00030004 May 1 19:59 audio0.3
crw-rw-rw- 1 root wheel 30, 3 May 9 12:08 dsp0.0
crw-rw-rw- 1 root wheel 30, 0x00010003 May 1 19:59 dsp0.1
crw-rw-rw- 1 root wheel 30, 0x00020003 May 1 19:59 dsp0.2
crw-rw-rw- 1 root wheel 30, 0x00030003 May 1 19:59 dsp0.3
crw-rw-rw- 1 root wheel 30, 5 May 1 19:59 dspW0.0
crw-rw-rw- 1 root wheel 30, 0x00010005 May 1 19:59 dspW0.1
crw-rw-rw- 1 root wheel 30, 0x00020005 May 1 19:59 dspW0.2
crw-rw-rw- 1 root wheel 30, 0x00030005 May 1 19:59 dspW0.3
crw-rw-rw- 1 root wheel 30, 2 May 1 19:59 midi0
crw-rw-rw- 1 root wheel 30, 0 May 1 19:59 mixer0
crw-rw-rw- 1 root wheel 30, 8 May 1 19:59 music0
crw-rw-rw- 1 root wheel 30, 9 May 1 19:59 pss0
crw-rw-rw- 1 root wheel 30, 1 May 1 19:59 sequencer0
crw-rw-rw- 1 root wheel 30, 6 May 1 19:59 sndstat
I've compiled KDE on my machine via pkgsrc.
Please tell me, if I've done something wrong, or what I could try out to get
kmix working.
I'm especially interested in replies of KDE users and if they have a working
or non-working kmix.
Thanks,
Thomas
Copyright (c) 2003, 2004, 2005, 2006 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
DragonFly 1.5.3-DEVELOPMENT #7: Mon May 1 19:26:35 CEST 2006
thomas@SchlesisNB.:/usr/obj/usr/src/sys/ASUS-V6800
TSC clock: 1728943742 Hz, i8254 clock: 1193143 Hz
CPU: Intel(R) Pentium(R) M processor 1.73GHz (1729.01-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8
Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
real memory = 2147090432 (2096768K bytes)
avail memory = 2075488256 (2026844K bytes)
Preloaded elf kernel "/kernel" at 0xc061c000.
Preloaded elf module "/modules/splash_bmp.ko" at 0xc061c210.
Preloaded elf module "/modules/vesa.ko" at 0xc061c2bc.
Preloaded splash_image_data "/boot/splash.bmp" at 0xc061c364.
Preloaded elf module "/modules/snd_ich.ko" at 0xc061c3b4.
Preloaded elf module "/modules/if_iwi.ko" at 0xc061c45c.
Preloaded elf module "/modules/acpi.ko" at 0xc061c504.
wlan: mac acl policy registered
Pentium Pro MTRR support enabled
md0: Malloc disk
pcibios: BIOS version 2.10
Using $PIR table, 12 entries at 0xc00f8660
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using XMM optimized bcopy/copyin/copyout
acpi0: <A M I OEMRSDT> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device. You can't run both
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU (4 Cx states)> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button1: <Power Button> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x66,0x62 on acpi0
legacypci0 on motherboard
pcib0: <Host to PCI bridge> on legacypci0
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=2591)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI model 3150 graphics accelerator> at 0.0 irq 10
pcib2: <PCI to PCI bridge (vendor=8086 device=2660)> at device 28.0 on pci0
pci2: <PCI bus> on pcib2
uhci0: <Intel 82801FB (ICH6) USB controller USB-A> port 0xa480-0xa49f irq 11 at device 29.0 on pci0
usb0: <Intel 82801FB (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB (ICH6) USB controller USB-B> port 0xa800-0xa81f irq 7 at device 29.1 on pci0
usb1: <Intel 82801FB (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB (ICH6) USB controller USB-C> port 0xa880-0xa89f irq 5 at device 29.2 on pci0
usb2: <Intel 82801FB (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB (ICH6) USB controller USB-D> port 0xac00-0xac1f irq 10 at device 29.3 on pci0
usb3: <Intel 82801FB (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <USB controller> at 29.7 irq 11
pcib3: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci3: <PCI bus> on pcib3
skc0: <Marvell Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfbffc000-0xfbffffff irq 5 at device 0.0 on pci3
skc0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
miibus0: <MII bus> on sk0
e1000phy0: <Marvell Semiconductor 88E1000* gigabit PHY> on miibus0
e1000phy0: 1000baseTX-FDX, 100baseTX-FDX, 100baseTX, 10baseTX-FDX, 10baseTX, auto
sk0: MAC address: 00:11:d8:89:ae:62
cbb0: <RF5C476 PCI-CardBus Bridge> at device 1.0 on pci3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib3: routed slot 1 INTA to irq 255
cbb: Unable to map IRQ...
device_probe_and_attach: cbb0 attach returned 12
fwohci0: <Ricoh R5C552> mem 0xfbffa800-0xfbffafff irq 10 at device 1.1 on pci3
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:e0:18:00:03:2a:34:57
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
fwe0: MAC address: 02:e0:18:2a:34:57
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci3: <unknown card> (vendor=0x1180, dev=0x0822) at 1.2 irq 5
pci3: <unknown card> (vendor=0x1180, dev=0x0592) at 1.3 irq 5
pci3: <unknown card> (vendor=0x1180, dev=0x0852) at 1.4 irq 5
iwi0: <Intel(R) PRO/Wireless 2200BG> mem 0xfbff9000-0xfbff9fff irq 5 at device 2.0 on pci3
iwi0: MAC address: 00:12:f0:07:f5:c8
pcm0: <Intel ICH6 (82801FB)> port 0x9c00-0x9c3f,0x9800-0x98ff mem 0xdffff400-0xdffff4ff,0xdffff800-0xdffff9ff irq 5 at device 30.2 on pci0
pcm0: <Avance Logic ALC650 AC97 Codec>
pci0: <unknown card> (vendor=0x8086, dev=0x266d) at 30.3 irq 6
isab0: <PCI to ISA bridge (vendor=8086 device=2641)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6R/RW ATA100 controller> port 0xffa0-0xffaf,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x266a) at 31.3
orm0: <Option ROM> at iomem 0xc0000-0xccfff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
system power profile changed to 'economy'
ad0: 57231MB <HTS548060M9AT00> [116280/16/63] at ata0-master UDMA100
acd0: DVD-R <MATSHITAUJ-822D> at ata0-slave UDMA33
pcm0: measured ac97 link rate at 44112 Hz
Mounting root from ufs:/dev/ad0s1a
cd0 at ata0 bus 0 target 1 lun 0
cd0: <MATSHITA UJ-822D 1.00> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
cpu0: Performance states changed
cpu0: Cx states changed
system power profile changed to 'performance'
iwi0: detached
cbb0: <RF5C476 PCI-CardBus Bridge> at device 1.0 on pci3
cardbus1: <CardBus bus> on cbb0
pccard1: <16-bit PCCard bus> on cbb0
pcib3: routed slot 1 INTA to irq 255
cbb: Unable to map IRQ...
device_probe_and_attach: cbb0 attach returned 12
iwi0: <Intel(R) PRO/Wireless 2200BG> mem 0xfbff9000-0xfbff9fff irq 5 at device 2.0 on pci3
iwi0: MAC address: 00:12:f0:07:f5:c8
May 9 09:21:56 SchlesisNB syslogd: kernel boot file is /kernel
May 9 09:21:56 SchlesisNB kernel: Copyright (c) 2003, 2004, 2005, 2006 The DragonFly Project.
May 9 09:21:56 SchlesisNB kernel: Copyright (c) 1992-2003 The FreeBSD Project.
May 9 09:21:56 SchlesisNB kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
May 9 09:21:56 SchlesisNB kernel: The Regents of the University of California. All rights reserved.
May 9 09:21:56 SchlesisNB kernel: DragonFly 1.5.3-DEVELOPMENT #7: Mon May 1 19:26:35 CEST 2006
May 9 09:21:56 SchlesisNB kernel: thomas@SchlesisNB.:/usr/obj/usr/src/sys/ASUS-V6800
May 9 09:21:56 SchlesisNB kernel: TSC clock: 1728943742 Hz, i8254 clock: 1193143 Hz
May 9 09:21:56 SchlesisNB kernel: CPU: Intel(R) Pentium(R) M processor 1.73GHz (1729.01-MHz 686-class CPU)
May 9 09:21:56 SchlesisNB kernel: Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8
May 9 09:21:56 SchlesisNB kernel: Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
May 9 09:21:56 SchlesisNB kernel: real memory = 2147090432 (2096768K bytes)
May 9 09:21:56 SchlesisNB kernel: avail memory = 2075488256 (2026844K bytes)
May 9 09:21:56 SchlesisNB kernel: Preloaded elf kernel "/kernel" at 0xc061c000.
May 9 09:21:56 SchlesisNB kernel: Preloaded elf module "/modules/splash_bmp.ko" at 0xc061c210.
May 9 09:21:56 SchlesisNB kernel: Preloaded elf module "/modules/vesa.ko" at 0xc061c2bc.
May 9 09:21:56 SchlesisNB kernel: Preloaded splash_image_data "/boot/splash.bmp" at 0xc061c364.
May 9 09:21:56 SchlesisNB kernel: Preloaded elf module "/modules/snd_ich.ko" at 0xc061c3b4.
May 9 09:21:56 SchlesisNB kernel: Preloaded elf module "/modules/if_iwi.ko" at 0xc061c45c.
May 9 09:21:56 SchlesisNB kernel: Preloaded elf module "/modules/acpi.ko" at 0xc061c504.
May 9 09:21:56 SchlesisNB kernel: wlan: mac acl policy registered
May 9 09:21:56 SchlesisNB kernel: Pentium Pro MTRR support enabled
May 9 09:21:56 SchlesisNB kernel: md0: Malloc disk
May 9 09:21:56 SchlesisNB kernel: pcibios: BIOS version 2.10
May 9 09:21:56 SchlesisNB kernel: Using $PIR table, 12 entries at 0xc00f8660
May 9 09:21:56 SchlesisNB kernel: npx0: <math processor> on motherboard
May 9 09:21:56 SchlesisNB kernel: npx0: INT 16 interface
May 9 09:21:56 SchlesisNB kernel: Using XMM optimized bcopy/copyin/copyout
May 9 09:21:56 SchlesisNB kernel: acpi0: <A M I OEMRSDT> on motherboard
May 9 09:21:56 SchlesisNB kernel: acpi_bus_number: can't get _ADR
May 9 09:21:56 SchlesisNB last message repeated 9 times
May 9 09:21:56 SchlesisNB kernel: acpi0: Power Button (fixed)
May 9 09:21:56 SchlesisNB kernel: Warning: ACPI is disabling APM's device. You can't run both
May 9 09:21:56 SchlesisNB kernel: acpi_bus_number: can't get _ADR
May 9 09:21:56 SchlesisNB kernel: acpi_bus_number: can't get _ADR
May 9 09:21:56 SchlesisNB kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
May 9 09:21:56 SchlesisNB kernel: cpu0: <ACPI CPU (4 Cx states)> on acpi0
May 9 09:21:56 SchlesisNB kernel: acpi_tz0: <Thermal Zone> on acpi0
May 9 09:21:56 SchlesisNB kernel: acpi_button0: <Sleep Button> on acpi0
May 9 09:21:56 SchlesisNB kernel: acpi_lid0: <Control Method Lid Switch> on acpi0
May 9 09:21:56 SchlesisNB kernel: acpi_button1: <Power Button> on acpi0
May 9 09:21:56 SchlesisNB kernel: acpi_cmbat0: <Control Method Battery> on acpi0
May 9 09:21:56 SchlesisNB kernel: acpi_acad0: <AC Adapter> on acpi0
May 9 09:21:56 SchlesisNB kernel: acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x66,0x62 on acpi0
May 9 09:21:56 SchlesisNB kernel: legacypci0 on motherboard
May 9 09:21:56 SchlesisNB kernel: pcib0: <Host to PCI bridge> on legacypci0
May 9 09:21:56 SchlesisNB kernel: pci0: <PCI bus> on pcib0
May 9 09:21:56 SchlesisNB kernel: pcib1: <PCI to PCI bridge (vendor=8086 device=2591)> at device 1.0 on pci0
May 9 09:21:56 SchlesisNB kernel: pci1: <PCI bus> on pcib1
May 9 09:21:56 SchlesisNB kernel: pci1: <ATI model 3150 graphics accelerator> at 0.0 irq 10
May 9 09:21:56 SchlesisNB kernel: pcib2: <PCI to PCI bridge (vendor=8086 device=2660)> at device 28.0 on pci0
May 9 09:21:56 SchlesisNB kernel: pci2: <PCI bus> on pcib2
May 9 09:21:56 SchlesisNB kernel: uhci0: <Intel 82801FB (ICH6) USB controller USB-A> port 0xa480-0xa49f irq 11 at device 29.0 on pci0
May 9 09:21:56 SchlesisNB kernel: usb0: <Intel 82801FB (ICH6) USB controller USB-A> on uhci0
May 9 09:21:56 SchlesisNB kernel: usb0: USB revision 1.0
May 9 09:21:56 SchlesisNB kernel: uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
May 9 09:21:56 SchlesisNB kernel: uhub0: 2 ports with 2 removable, self powered
May 9 09:21:56 SchlesisNB kernel: uhci1: <Intel 82801FB (ICH6) USB controller USB-B> port 0xa800-0xa81f irq 7 at device 29.1 on pci0
May 9 09:21:56 SchlesisNB kernel: usb1: <Intel 82801FB (ICH6) USB controller USB-B> on uhci1
May 9 09:21:56 SchlesisNB kernel: usb1: USB revision 1.0
May 9 09:21:56 SchlesisNB kernel: uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
May 9 09:21:56 SchlesisNB kernel: uhub1: 2 ports with 2 removable, self powered
May 9 09:21:56 SchlesisNB kernel: uhci2: <Intel 82801FB (ICH6) USB controller USB-C> port 0xa880-0xa89f irq 5 at device 29.2 on pci0
May 9 09:21:56 SchlesisNB kernel: usb2: <Intel 82801FB (ICH6) USB controller USB-C> on uhci2
May 9 09:21:56 SchlesisNB kernel: usb2: USB revision 1.0
May 9 09:21:56 SchlesisNB kernel: uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
May 9 09:21:56 SchlesisNB kernel: uhub2: 2 ports with 2 removable, self powered
May 9 09:21:56 SchlesisNB kernel: uhci3: <Intel 82801FB (ICH6) USB controller USB-D> port 0xac00-0xac1f irq 10 at device 29.3 on pci0
May 9 09:21:56 SchlesisNB kernel: usb3: <Intel 82801FB (ICH6) USB controller USB-D> on uhci3
May 9 09:21:56 SchlesisNB kernel: usb3: USB revision 1.0
May 9 09:21:56 SchlesisNB kernel: uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
May 9 09:21:56 SchlesisNB kernel: uhub3: 2 ports with 2 removable, self powered
May 9 09:21:56 SchlesisNB kernel: pci0: <USB controller> at 29.7 irq 11
May 9 09:21:56 SchlesisNB kernel: pcib3: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
May 9 09:21:56 SchlesisNB kernel: pci3: <PCI bus> on pcib3
May 9 09:21:56 SchlesisNB kernel: skc0: <Marvell Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfbffc000-0xfbffffff irq 5 at device 0.0 on pci3
May 9 09:21:56 SchlesisNB kernel: skc0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
May 9 09:21:56 SchlesisNB kernel: sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
May 9 09:21:56 SchlesisNB kernel: miibus0: <MII bus> on sk0
May 9 09:21:56 SchlesisNB kernel: e1000phy0: <Marvell Semiconductor 88E1000* gigabit PHY> on miibus0
May 9 09:21:56 SchlesisNB kernel: e1000phy0: 1000baseTX-FDX, 100baseTX-FDX, 100baseTX, 10baseTX-FDX, 10baseTX, auto
May 9 09:21:56 SchlesisNB kernel: sk0: MAC address: 00:11:d8:89:ae:62
May 9 09:21:56 SchlesisNB kernel: cbb0: <RF5C476 PCI-CardBus Bridge> at device 1.0 on pci3
May 9 09:21:56 SchlesisNB kernel: cardbus0: <CardBus bus> on cbb0
May 9 09:21:56 SchlesisNB kernel: pccard0: <16-bit PCCard bus> on cbb0
May 9 09:21:56 SchlesisNB kernel: pcib3: routed slot 1 INTA to irq 255
May 9 09:21:56 SchlesisNB kernel: cbb: Unable to map IRQ...
May 9 09:21:56 SchlesisNB kernel: device_probe_and_attach: cbb0 attach returned 12
May 9 09:21:56 SchlesisNB kernel: fwohci0: <Ricoh R5C552> mem 0xfbffa800-0xfbffafff irq 10 at device 1.1 on pci3
May 9 09:21:56 SchlesisNB kernel: fwohci0: OHCI version 1.0 (ROM=1)
May 9 09:21:56 SchlesisNB kernel: fwohci0: No. of Isochronous channel is 4.
May 9 09:21:56 SchlesisNB kernel: fwohci0: EUI64 00:e0:18:00:03:2a:34:57
May 9 09:21:56 SchlesisNB kernel: fwohci0: Phy 1394a available S400, 2 ports.
May 9 09:21:56 SchlesisNB kernel: fwohci0: Link S400, max_rec 2048 bytes.
May 9 09:21:56 SchlesisNB kernel: firewire0: <IEEE1394(FireWire) bus> on fwohci0
May 9 09:21:56 SchlesisNB kernel: fwe0: <Ethernet over FireWire> on firewire0
May 9 09:21:56 SchlesisNB kernel: fwe0: MAC address: 02:e0:18:2a:34:57
May 9 09:21:56 SchlesisNB kernel: sbp0: <SBP-2/SCSI over FireWire> on firewire0
May 9 09:21:56 SchlesisNB kernel: fwohci0: Initiate bus reset
May 9 09:21:56 SchlesisNB kernel: fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
May 9 09:21:56 SchlesisNB kernel: firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
May 9 09:21:56 SchlesisNB kernel: firewire0: bus manager 0 (me)
May 9 09:21:56 SchlesisNB kernel: pci3: <unknown card> (vendor=0x1180, dev=0x0822) at 1.2 irq 5
May 9 09:21:56 SchlesisNB kernel: pci3: <unknown card> (vendor=0x1180, dev=0x0592) at 1.3 irq 5
May 9 09:21:56 SchlesisNB kernel: pci3: <unknown card> (vendor=0x1180, dev=0x0852) at 1.4 irq 5
May 9 09:21:56 SchlesisNB kernel: iwi0: <Intel(R) PRO/Wireless 2200BG> mem 0xfbff9000-0xfbff9fff irq 5 at device 2.0 on pci3
May 9 09:21:56 SchlesisNB kernel: iwi0: MAC address: 00:12:f0:07:f5:c8
May 9 09:21:56 SchlesisNB kernel: pcm0: <Intel ICH6 (82801FB)> port 0x9c00-0x9c3f,0x9800-0x98ff mem 0xdffff400-0xdffff4ff,0xdffff800-0xdffff9ff irq 5 at device 30.2 on pci0
May 9 09:21:56 SchlesisNB kernel: pcm0: <Avance Logic ALC650 AC97 Codec>
May 9 09:21:56 SchlesisNB kernel: pci0: <unknown card> (vendor=0x8086, dev=0x266d) at 30.3 irq 6
May 9 09:21:56 SchlesisNB kernel: isab0: <PCI to ISA bridge (vendor=8086 device=2641)> at device 31.0 on pci0
May 9 09:21:56 SchlesisNB kernel: isa0: <ISA bus> on isab0
May 9 09:21:56 SchlesisNB kernel: atapci0: <Intel ICH6R/RW ATA100 controller> port 0xffa0-0xffaf,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
May 9 09:21:56 SchlesisNB kernel: ata0: at 0x1f0 irq 14 on atapci0
May 9 09:21:56 SchlesisNB kernel: ata1: at 0x170 irq 15 on atapci0
May 9 09:21:56 SchlesisNB kernel: pci0: <unknown card> (vendor=0x8086, dev=0x266a) at 31.3
May 9 09:21:56 SchlesisNB kernel: orm0: <Option ROM> at iomem 0xc0000-0xccfff on isa0
May 9 09:21:56 SchlesisNB kernel: pmtimer0 on isa0
May 9 09:21:56 SchlesisNB kernel: atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
May 9 09:21:56 SchlesisNB kernel: atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
May 9 09:21:56 SchlesisNB kernel: kbd0 at atkbd0
May 9 09:21:56 SchlesisNB kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0
May 9 09:21:56 SchlesisNB kernel: psm0: model Generic PS/2 mouse, device ID 0
May 9 09:21:56 SchlesisNB kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
May 9 09:21:56 SchlesisNB kernel: sc0: <System console> at flags 0x100 on isa0
May 9 09:21:56 SchlesisNB kernel: sc0: VGA <16 virtual consoles, flags=0x300>
May 9 09:21:56 SchlesisNB kernel: acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
May 9 09:21:56 SchlesisNB kernel: system power profile changed to 'economy'
May 9 09:21:56 SchlesisNB kernel: ad0: 57231MB <HTS548060M9AT00> [116280/16/63] at ata0-master UDMA100
May 9 09:21:56 SchlesisNB kernel: acd0: DVD-R <MATSHITAUJ-822D> at ata0-slave UDMA33
May 9 09:21:56 SchlesisNB kernel: pcm0: measured ac97 link rate at 44112 Hz
May 9 09:21:56 SchlesisNB kernel: Mounting root from ufs:/dev/ad0s1a
May 9 09:21:56 SchlesisNB kernel: cd0 at ata0 bus 0 target 1 lun 0
May 9 09:21:56 SchlesisNB kernel: cd0: <MATSHITA UJ-822D 1.00> Removable CD-ROM SCSI-0 device
May 9 09:21:56 SchlesisNB kernel: cd0: 33.000MB/s transfers
May 9 09:21:56 SchlesisNB kernel: cd0: Attempt to query device size failed: NOT READY, Medium not present
May 9 09:22:43 SchlesisNB login: ROOT LOGIN (root) ON ttyv0
May 9 09:45:14 SchlesisNB kernel: cpu0: Performance states changed
May 9 09:45:14 SchlesisNB kernel: cpu0: Cx states changed
May 9 09:45:14 SchlesisNB kernel: system power profile changed to 'performance'
May 9 10:23:13 SchlesisNB su: thomas to root on /dev/ttyp1
May 9 11:38:29 SchlesisNB kernel: iwi0: detached
May 9 11:38:29 SchlesisNB kernel: cbb0: <RF5C476 PCI-CardBus Bridge> at device 1.0 on pci3
May 9 11:38:29 SchlesisNB kernel: cardbus1: <CardBus bus> on cbb0
May 9 11:38:29 SchlesisNB kernel: pccard1: <16-bit PCCard bus> on cbb0
May 9 11:38:29 SchlesisNB kernel: pcib3: routed slot 1 INTA to irq 255
May 9 11:38:29 SchlesisNB kernel: cbb: Unable to map IRQ...
May 9 11:38:29 SchlesisNB kernel: device_probe_and_attach: cbb0 attach returned 12
May 9 11:38:29 SchlesisNB kernel: iwi0: <Intel(R) PRO/Wireless 2200BG> mem 0xfbff9000-0xfbff9fff irq 5 at device 2.0 on pci3
May 9 11:38:29 SchlesisNB kernel: iwi0: MAC address: 00:12:f0:07:f5:c8
[
Date Prev][
Date Next]
[
Thread Prev][
Thread Next]
[
Date Index][
Thread Index]
