Re: Xircom cardbus NIC not working

[Sepherosa Ziehau <sepherosa@xxxxxxxxx>]

This is a dc(4) card.

Please try:
http://leaf.dragonflybsd.org/~sephe/if_dc_xircom.diff

Best Regards,
sephe

On 12/26/05, Tim Darby <t-df@xxxxxxxxxxxx> wrote:
> Hi all and Merry Christmas!  I've been watching the DF lists for awhile
> now and just want to thank Matt and everyone else for all the great work
> on DragonFly.  I can't wait for upcoming new stuff, especially ZFS.
> I've been running OpenBSD servers for some time but I'm a noob to DF so
> bare with me.  I tried to boot 1.4 RC1 this morning and ran into a snag
> with my Realport Cardbus 10/100 NIC.  I hope the attached dmesg helps.
>
> Tim
>
> Copyright (c) 2003, 2004, 2005 The DragonFly Project.
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> DragonFly 1.4.0-RELEASE #2: Fri Dec 23 13:04:39 PST 2005
>     root@xxxxxxxxxxxxxxxxxxxx:/usr/obj/usr/src/sys/GENERIC
> TSC clock: 366645245 Hz, i8254 clock: 1193098 Hz
> CPU: Pentium II/Pentium II Xeon/Celeron (366.67-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x66a  Stepping = 10
>   Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
> real memory  = 201326592 (196608K bytes)
> avail memory = 183836672 (179528K bytes)
> pnpbios: Bad PnP BIOS data checksum
> Preloaded elf kernel "/kernel" at 0xc06b6000.
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> pcibios: BIOS version 2.10
> Using $PIR table, 6 entries at 0xc00fdf60
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> legacypci0 on motherboard
> pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on legacypci0
> pci0: <PCI bus> on pcib0
> agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
> pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> pci1: <ATI model 4c42 graphics accelerator> at 0.0 irq 11
> pci0: <unknown card> (vendor=0x1287, dev=0x0020) at 3.0 irq 11
> cbb0: <TI1220 PCI-CardBus Bridge> at device 4.0 on pci0
> cardbus0: <CardBus bus> on cbb0
> pccard0: <16-bit PCCard bus> on cbb0
> pci_cfgintr: 0:4 INTA routed to irq 11
> cbb1: <TI1220 PCI-CardBus Bridge> at device 4.1 on pci0
> cardbus1: <CardBus bus> on cbb1
> pccard1: <16-bit PCCard bus> on cbb1
> pci_cfgintr: 0:4 INTB routed to irq 11
> isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX4 ATA33 controller> port 0xfcd0-0xfcdf at device 7.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xfce0-0xfcff irq 11 at device 7.2 on pci0
> usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> pci0: <Intel 82371AB Power management controller> at 7.3
> pci0: <unknown card> (vendor=0x125d, dev=0x1968) at 8.0 irq 5
> orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model Generic PS/2 mouse, device ID 0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: configured irq 3 not in bitmap of probed irqs 0
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/7 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> ata1-slave: ATAPI identify retries exceeded
> Product version: 5.0
> Product name: IBM | 10/100 EtherJet CardBus | IBMC-10/100 | 1.04 |
> Manufacturer ID: a400130181
> Functions: Network Adaptor, Multi-Functioned
> Function Extension: 040600062925a3c5
> Function Extension: 0102
> Function Extension: 0280969800
> Function Extension: 0200e1f505
> Function Extension: 0301
> Function Extension: 0303
> Function Extension: 0501
> cardbus0: Invalid BAR number: 27(06)
> CIS reading done
> cardbus0: <unknown card> (vendor=0x115d, dev=0x0003) at 0.0 irq 11
> cbb0: CardBus card activation failed
> ad0: 17301MB <IBM-DJSA-220> [35152/16/63] at ata0-master UDMA33
> acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2102> at ata1-master PIO4
> Mounting root from cd9660:cd0c
> cd0 at ata1 bus 0 target 0 lun 0
> cd0: <TOSHIBA DVD-ROM SD-C2102 1029> Removable CD-ROM SCSI-0 device
> cd0: 16.000MB/s transfers
> cd0: cd present [114288 x 2048 byte records]
>
>
>


--
Live Free or Die