DragonFly BSD
DragonFly users List (threaded) for 2011-07
[Date Prev][Date Next]  [Thread Prev][Thread Next]  [Date Index][Thread Index]

Re: Rebbot after upgrade to v2.11.0-568-gf1c1aea puts me to the ddb prompt in i386


From: Siju George <sgeorge.ml@xxxxxxxxx>
Date: Thu, 21 Jul 2011 16:17:34 +0530

On Thu, Jul 21, 2011 at 3:13 PM, Sepherosa Ziehau <sepherosa@gmail.com> wrote:
>
>
> Hmm, make sure that you have done a full buildkernel instead of quickkernel
>

Yes I always do a full buildkernel :-)

>Please post following information:
>acpidump -t
>

dfly-bkpsrv# acpidump -t
/*
  RSD PTR: OEM=ACPIAM, ACPI_Rev=1.0x (0)
        RSDT=0x7dfd0000, cksum=188
 */
/*
  RSDT: Length=52, Revision=1, Checksum=141,
        OEMID=A M I, OEM Table ID=OEMRSDT, OEM Revision=0x1000624,
        Creator ID=MSFT, Creator Revision=0x97
        Entries={ 0x7dfd0200, 0x7dfd0390, 0x7dfd03f0, 0x7dfde040 }
 */
/*
  FACP: Length=132, Revision=2, Checksum=82,
        OEMID=A M I, OEM Table ID=OEMFACP, OEM Revision=0x1000624,
        Creator ID=MSFT, Creator Revision=0x97
        FACS=0x7dfde000, DSDT=0x7dfd0430
        INT_MODEL=APIC
        Preferred_PM_Profile=Unspecified (0)
        SCI_INT=9
        SMI_CMD=0xb0, ACPI_ENABLE=0xe1, ACPI_DISABLE=0x1e, S4BIOS_REQ=0x0
        PSTATE_CNT=0xe2
        PM1a_EVT_BLK=0x800-0x803
        PM1a_CNT_BLK=0x804-0x805
        PM2_CNT_BLK=0x880-0x880
        PM_TMR_BLK=0x808-0x80b
        GPE0_BLK=0x820-0x827
        P_LVL2_LAT=101 us, P_LVL3_LAT=1001 us
        FLUSH_SIZE=1024, FLUSH_STRIDE=16
        DUTY_OFFSET=4, DUTY_WIDTH=3
        DAY_ALRM=13, MON_ALRM=0, CENTURY=0
        IAPC_BOOT_ARCH={LEGACY_DEV,8042}
        Flags={WBINVD,PROC_C1,SLP_BUTTON,RTC_S4,TMR_VAL_EXT}
 */
/*
  FACS: Length=64, HwSig=0x00000000, Firm_Wake_Vec=0x00000000
        Global_Lock=
        Flags=
        Version=1
 */
/*
  DSDT: Length=14964, Revision=1, Checksum=105,
        OEMID=1ABZR, OEM Table ID=1ABZRB49, OEM Revision=0xb49,
        Creator ID=INTL, Creator Revision=0x2002026
 */
/*
  APIC: Length=92, Revision=1, Checksum=174,
        OEMID=A M I, OEM Table ID=OEMAPIC, OEM Revision=0x1000624,
        Creator ID=MSFT, Creator Revision=0x97
        Local APIC ADDR=0xfee00000
        Flags={PC-AT}

        Type=Local APIC
        ACPI CPU=1
        Flags={ENABLED}
        APIC ID=0

        Type=Local APIC
        ACPI CPU=2
        Flags={DISABLED}
        APIC ID=129

        Type=IO APIC
        APIC ID=1
        INT BASE=0
        ADDR=0x00000000fec00000

        Type=INT Override
        BUS=0
        IRQ=0
        INTR=2
        Flags={Polarity=conforming, Trigger=conforming}

        Type=INT Override
        BUS=0
        IRQ=9
        INTR=21
        Flags={Polarity=active-lo, Trigger=level}
 */
/*
  MCFG: Length=60, Revision=1, Checksum=118,
        OEMID=A M I, OEM Table ID=OEMMCFG, OEM Revision=0x1000624,
        Creator ID=MSFT, Creator Revision=0x97

        Base Address= 0x00000000e0000000
        Segment Group= 0x0000
        Start Bus= 0
        End Bus= 255
 */
acpidump: RSDT entry 3 (sig OEMB) is corrupt
dfly-bkpsrv#


>enable boot_versbose and post the dmesg before the panic
>

Copyright (c) 2003-2011 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
Slab ZoneSize set to 128KB
Leaving critical section, allowing interrupts
ACPI SDT: RSDP in BIOS mem
ACPI FADT: SCI irq 9, conform/conform
DragonFly v2.11.0.247.gda17d9-DEVELOPMENT #36: Mon May 23 12:57:37 IST 2011
    root@dfly-bkpsrv.hifxnx.local:/usr/obj/usr/src/sys/GENERIC
Calibrating clock(s) ... TSC clock: 2193650213 Hz, i8254 clock: 1193201 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: AMD Athlon(tm) 64 Processor 3400+ (2193.63-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x20ff2  Stepping = 2
  Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  Features2=0x1<SSE3>
  AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow!+,3DNow!>
  AMD Features2=0x1<LAHF>
Data TLB: 32 entries, fully associative
Instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
WARNING: This architecture revision has known SMP hardware bugs which
may cause random instability
real memory  = 2113336320 (2015 MB)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x009fd000 - 0x7dfaffff, 2103128064 bytes (513459 pages)
avail memory = 2029371392 (1935 MB)
ELCR Found.  ISA IRQs programmed as:
  0  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15
  E  E  E  E  L  L  E  E  E  E  L  L  E  E  E  E
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0x31
pnpbios: Found PnP BIOS data at 0xc00f5860
pnpbios: Entry = f0000:664a  Rev = 1.0
Other BIOS signatures found:
ndepotmags=438 x mag_cap=128 for mbuf
ndepotmags=4   x mag_cap=33  for mbuf pkt hdr
ndepotmags=27  x mag_cap=128 for cluster mbuf
ndepotmags=27  x mag_cap=128 for jcluster mbuf
ndepotmags=27  x mag_cap=128 for mbuf + cluster
ndepotmags=4   x mag_cap=33  for mbuf pkt hdr + cluster
ndepotmags=27  x mag_cap=128 for mbuf + jcluster
ndepotmags=4   x mag_cap=17  for mbuf pkt hdr + jcluster
ndepotmags=4   x mag_cap=33  for CCMS
ndepotmags=4   x mag_cap=33  for lwbuf
ndepotmags=4   x mag_cap=33  for sf_buf
ndepotmags=3   x mag_cap=4   for exec-args
Preloaded elf kernel "kernel" at 0xc09ce000.
Preloaded elf module "acpi.ko" at 0xc09ce1f4.
Preloaded elf module "ahci.ko" at 0xc09ce290.
Preloaded elf module "ehci.ko" at 0xc09ce32c.
module_register: module pci/ahci already exists!
Module pci/ahci failed to register: 17
ndepotmags=4   x mag_cap=9   for thread
ndepotmags=4   x mag_cap=33  for dsched-tdio-cache
ndepotmags=4   x mag_cap=33  for dsched-tdctx-cache
ndepotmags=4   x mag_cap=33  for dsched-diskctx-cache
ndepotmags=4   x mag_cap=9   for vmspace
ndepotmags=4   x mag_cap=33  for disk-msg-cache
ndepotmags=4   x mag_cap=33  for devfs-node-cache
ndepotmags=4   x mag_cap=33  for devfs-msg-cache
ndepotmags=4   x mag_cap=33  for devfs-dev-cache
FQ scheduler policy version 1.0 loaded
ndepotmags=4   x mag_cap=33  for propdict
ndepotmags=4   x mag_cap=33  for propstng
ndepotmags=4   x mag_cap=33  for pdict128
ndepotmags=4   x mag_cap=33  for propdata
ndepotmags=4   x mag_cap=33  for pdict32
ndepotmags=4   x mag_cap=33  for proparay
ndepotmags=4   x mag_cap=33  for pdict16
ndepotmags=4   x mag_cap=33  for propnmbr
ndepotmags=4   x mag_cap=9   for devfs
ndepotmags=4   x mag_cap=33  for devfs-rule-cache
wlan: <802.11 Link Layer>
ndepotmags=4   x mag_cap=33  for ata_request
ndepotmags=4   x mag_cap=33  for ata_composite
No policy for md0 specified, or policy not found
disk scheduler: set policy of md0 to noop
md0: Malloc disk
kbd: new array size 4
kbd1 at kbdmux0
ndepotmags=4   x mag_cap=33  for crypto op
ndepotmags=4   x mag_cap=33  for crypto desc
crypto: <crypto core>
Pentium Pro MTRR support enabled
md0: invalid primary partition table: no magic
Math emulator present
ACPI: RSDP 0xf96f0 00014 (v0 ACPIAM)
ACPI: RSDT 0x7dfd0000 00034 (v1 A M I  OEMRSDT  01000624 MSFT 00000097)
ACPI: FACP 0x7dfd0200 00084 (v2 A M I  OEMFACP  01000624 MSFT 00000097)
ACPI: DSDT 0x7dfd0430 03A74 (v1  1ABZR 1ABZRB49 00000B49 INTL 02002026)
ACPI: FACS 0x7dfde000 00040
ACPI: APIC 0x7dfd0390 0005C (v1 A M I  OEMAPIC  01000624 MSFT 00000097)
ACPI: MCFG 0x7dfd03f0 0003C (v1 A M I  OEMMCFG  01000624 MSFT 00000097)
ACPI: OEMB 0x7dfde040 00056 (v1 A M I  AMI_OEM  01000624 MSFT 00000097)
npx0.nexus0.root0
npx0: <math processor> [tentative] on motherboard
npx0: INT 16 interface
Using XMM optimized bcopy/copyin/copyout
npx0: <math processor> [attached!] on motherboard
cryptosoft0.nexus0.root0
cryptosoft0: <software crypto> [tentative] on motherboard
crypto: assign cryptosoft0 driver id 0, flags 234881024
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
cryptosoft0: <software crypto> [attached!] on motherboard
acpi0.nexus0.root0
acpi0: <A M I OEMRSDT> [tentative] on motherboard
ndepotmags=4   x mag_cap=33  for Acpi-Namespace
ndepotmags=4   x mag_cap=33  for Acpi-State
ndepotmags=4   x mag_cap=33  for Acpi-Parse
ndepotmags=4   x mag_cap=33  for Acpi-ParseExt
ndepotmags=4   x mag_cap=33  for Acpi-Operand
ACPI FADT: SCI testing interrupt mode ...
ACPI FADT: SCI testing level/low
ICU: irq 9, edge -> level
ACPI FADT: SCI select level/low
ACPI: Executed 1 blocks of module-level executable AML code
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device.  You can't run both
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks GOOD min = 5, max = 7, width = 2
ACPI timer looks BAD  min = 5, max = 1303, width = 1298
acpi_timer0.acpi0.nexus0.root0
acpi_timer0: <32-bit timer at 3.579545MHz> [tentative] port 0x808-0x80b on acpi0
acpi_timer0: <32-bit timer at 3.579545MHz> [attached!] port 0x808-0x80b on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    5   N     0  3 4 5 7 10 11 12 14 15
  Validation          0    5   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 7 10 11 12 14 15
  Validation          0   10   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    4   N     0  3 4 5 7 10 11 12 14 15
  Validation          0    4   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   15   N     0  3 4 5 7 10 11 12 14 15
  Validation          0   15   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  9
  Validation          0  255   N     0  9
  After Disable       0  255   N     0  9
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    5   N     0  3 4 5 7 10 11 12 14 15
  Validation          0    5   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 7 10 11 12 14 15
  Validation          0   11   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_open(1):    mode 1 addr port (0x0cf8) is 0x80012814
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=59501002)
pcibios: BIOS version 3.00
pcib0.acpi0.nexus0.root0
pcib0: <ACPI Host-PCI bridge> [tentative] port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.20.INTA at func 1: 255
ACPI: Found matching pin for 0.20.INTA at func 2: 5
ACPI: Found matching pin for 0.18.INTA at func 0: 5
ACPI: Found matching pin for 0.17.INTA at func 0: 11
ACPI: Found matching pin for 0.19.INTA at func 0: 4
pci0.pcib0.acpi0.nexus0.root0
pci0: <ACPI PCI bus> [tentative] on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1002, dev=0x5950, revid=0x10
        domain=0, bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x2220, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1002, dev=0x5a3f, revid=0x00
        domain=0, bus=0, slot=1, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x0230, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1002, dev=0x437a, revid=0x80
        domain=0, bus=0, slot=17, func=0
        class=01-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 1 message
        map[10]: type I/O Port, range 32, base 0xb800, size  3, enabled
        map[14]: type I/O Port, range 32, base 0xb400, size  2, enabled
        map[18]: type I/O Port, range 32, base 0xb000, size  3, enabled
        map[1c]: type I/O Port, range 32, base 0xa800, size  2, enabled
        map[20]: type I/O Port, range 32, base 0xa400, size  4, enabled
        map[24]: type Memory, range 32, base 0xfe9fbc00, size  9, enabled
pcib0: matched entry for 0.17.INTA (src \\_SB_.LNKH:0)
pcib0: slot 17 INTA routed to irq 11 via \\_SB_.LNKH
found-> vendor=0x1002, dev=0x4379, revid=0x80
        domain=0, bus=0, slot=18, func=0
        class=01-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=5
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 1 message
        map[10]: type I/O Port, range 32, base 0xa000, size  3, enabled
        map[14]: type I/O Port, range 32, base 0x9800, size  2, enabled
        map[18]: type I/O Port, range 32, base 0x9400, size  3, enabled
        map[1c]: type I/O Port, range 32, base 0x9000, size  2, enabled
        map[20]: type I/O Port, range 32, base 0x8800, size  4, enabled
        map[24]: type Memory, range 32, base 0xfe9fb800, size  9, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.LNKG:0)
pcib0: slot 18 INTA routed to irq 5 via \\_SB_.LNKG
found-> vendor=0x1002, dev=0x4374, revid=0x80
        domain=0, bus=0, slot=19, func=0
        class=0c-03-10, hdrtype=0x00, mfdev=1
        cmdreg=0x0117, statreg=0x02b0, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=4
        MSI supports 1 message
        map[10]: type Memory, range 32, base 0xfe9fa000, size 12, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKD:0)
pcib0: slot 19 INTA routed to irq 4 via \\_SB_.LNKD
found-> vendor=0x1002, dev=0x4375, revid=0x80
        domain=0, bus=0, slot=19, func=1
        class=0c-03-10, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x02b0, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=4
        MSI supports 1 message
        map[10]: type Memory, range 32, base 0xfe9f9000, size 12, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKD:0)
pcib0: slot 19 INTA routed to irq 4 via \\_SB_.LNKD
found-> vendor=0x1002, dev=0x4373, revid=0x80
        domain=0, bus=0, slot=19, func=2
        class=0c-03-20, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x02b0, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=4
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 1 message
        map[10]: type Memory, range 32, base 0xfe9f8000, size 12, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKD:0)
pcib0: slot 19 INTA routed to irq 4 via \\_SB_.LNKD
found-> vendor=0x1002, dev=0x4372, revid=0x81
        domain=0, bus=0, slot=20, func=0
        class=0c-05-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0403, statreg=0x0230, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[10]: type I/O Port, range 32, base 0xb00, size  4, enabled
        map[14]: type Memory, range 32, base 0, size 10, enabled
found-> vendor=0x1002, dev=0x4376, revid=0x80
        domain=0, bus=0, slot=20, func=1
        class=01-01-8a, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0230, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=255
        MSI supports 1 message
        map[20]: type I/O Port, range 32, base 0xff00, size  4, enabled
found-> vendor=0x1002, dev=0x437b, revid=0x01
        domain=0, bus=0, slot=20, func=2
        class=04-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=5
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type Memory, range 64, base 0xfe9e8000, size 14, enabled
pcib0: matched entry for 0.20.INTA (src \\_SB_.LNKA:0)
pcib0: slot 20 INTA routed to irq 5 via \\_SB_.LNKA
found-> vendor=0x1002, dev=0x4377, revid=0x80
        domain=0, bus=0, slot=20, func=3
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x010f, statreg=0x0220, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1002, dev=0x4371, revid=0x80
        domain=0, bus=0, slot=20, func=4
        class=06-04-01, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x02a0, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1100, revid=0x00
        domain=0, bus=0, slot=24, func=0
        class=06-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
        domain=0, bus=0, slot=24, func=1
        class=06-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
        domain=0, bus=0, slot=24, func=2
        class=06-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
        domain=0, bus=0, slot=24, func=3
        class=06-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1.pci0.pcib0.acpi0.nexus0.root0
pcib1: <ACPI PCI-PCI bridge> [tentative] at device 1.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xd000-0xdfff
pcib1:   memory decode     0xfea00000-0xfeafffff
pcib1:   prefetched decode 0xf8000000-0xfbffffff
ACPI: Found matching pin for 1.5.INTA at func 0: 10
pci1.pcib1.pci0.pcib0.acpi0.nexus0.root0
pci1: <ACPI PCI bus> [tentative] on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x1002, dev=0x5974, revid=0x00
        domain=0, bus=1, slot=5, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Prefetchable Memory, range 32, base 0xf8000000,
size 26, enabled
pcib1: requested memory range 0xf8000000-0xfbffffff: good
        map[14]: type I/O Port, range 32, base 0xd800, size  8, enabled
pcib1: requested I/O range 0xd800-0xd8ff: in range
        map[18]: type Memory, range 32, base 0xfeaf0000, size 16, enabled
pcib1: requested memory range 0xfeaf0000-0xfeafffff: good
pcib1: matched entry for 1.5.INTA (src \\_SB_.LNKB:0)
pcib1: slot 5 INTA routed to irq 10 via \\_SB_.LNKB
vgapci0.pci1.pcib1.pci0.pcib0.acpi0.nexus0.root0
vgapci0: <VGA-compatible display> [tentative] port 0xd800-0xd8ff mem
0xfeaf0000-0xfeafffff,0xf8000000-0xfbffffff irq 10 at device 5.0 on
pci1
vgapci0: <VGA-compatible display> [attached!] port 0xd800-0xd8ff mem
0xfeaf0000-0xfeafffff,0xf8000000-0xfbffffff irq 10 at device 5.0 on
pci1
pci1: <ACPI PCI bus> [attached!] on pcib1
pcib1: <ACPI PCI-PCI bridge> [attached!] at device 1.0 on pci0
atapci0.pci0.pcib0.acpi0.nexus0.root0
atapci0: <ATI IXP400 SATA150 controller> [tentative] port
0xa400-0xa40f,0xa800-0xa803,0xb000-0xb007,0xb400-0xb403,0xb800-0xb807
mem 0xfe9fbc00-0xfe9fbdff irq 11 at device 17.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xa400
atapci0: Reserved 0x200 bytes for rid 0x24 type 3 at 0xfe9fbc00
ata2.atapci0.pci0.pcib0.acpi0.nexus0.root0
ata2: <ATA channel 0> [tentative] on atapci0
ata2: SATA connect time=0ms
sched_ithd: stray interrupt 7 on cpu 0
ata2: reset tp1 mask=01 ostat0=50 ostat1=00
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
No policy for ad4 specified, or policy not found
disk scheduler: set policy of ad4 to noop
ad4: Silicon Image check3 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ad4: 476940MB <Seagate ST3500620AS SD1A> at ata2-master SATA150
ad4: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
ata2: <ATA channel 0> [attached!] on atapci0
ata3.atapci0.pci0.pcib0.acpi0.nexus0.root0
ata3: <ATA channel 1> [tentative] on atapci0
ata3: SATA connect time=0ms
sched_ithd: stray interrupt 7 on cpu 0
ata3: reset tp1 mask=01 ostat0=50 ostat1=00
ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
No policy for ad6 specified, or policy not found
disk scheduler: set policy of ad6 to noop
ad4: type 0xa5, start 63, end = 976773167, size 976773105 : OK
ad6: Silicon Image check3 failed
ad6: Adaptec check1 failed
ad6: LSI (v3) check1 failed
ad6: LSI (v2) check1 failed
ad6: FreeBSD check1 failed
ad6: 476940MB <Seagate ST3500620AS SD1A> at ata3-master SATA150
ad6: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
ata3: <ATA channel 1> [attached!] on atapci0
atapci0: <ATI IXP400 SATA150 controller> [attached!] port
0xa400-0xa40f,0xa800-0xa803,0xb000-0xb007,0xb400-0xb403,0xb800-0xb807
mem 0xfe9fbc00-0xfe9fbdff irq 11 at device 17.0 on pci0
atapci1.pci0.pcib0.acpi0.nexus0.root0
atapci1: <ATI IXP400 SATA150 controller> [tentative] port
0x8800-0x880f,0x9000-0x9003,0x9400-0x9407,0x9800-0x9803,0xa000-0xa007
mem 0xfe9fb800-0xfe9fb9ff irq 5 at device 18.0 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x8800
atapci1: Reserved 0x200 bytes for rid 0x24 type 3 at 0xfe9fb800
ata4.atapci1.pci0.pcib0.acpi0.nexus0.root0
ata4: <ATA channel 0> [tentative] on atapci1
intr 5 at 40001/40000 hz, livelocked limit engaged!
ata4: SATA connect time=0ms
ata4: reset tp1 mask=01 ostat0=50 ostat1=00
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ad6: type 0xa5, start 63, end = 976773167, size 976773105 : OK
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
intr 5 at 40006/20000 hz, in livelock
No policy for ad8 specified, or policy not found
disk scheduler: set policy of ad8 to noop
ad8: Silicon Image check3 failed
ad8: Adaptec check1 failed
ad8: LSI (v3) check1 failed
ad8: LSI (v2) check1 failed
ad8: FreeBSD check1 failed
ad8: 476940MB <Seagate ST3500418AS CC38> at ata4-master SATA150
ad8: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
ata4: <ATA channel 0> [attached!] on atapci1
ata5.atapci1.pci0.pcib0.acpi0.nexus0.root0
ata5: <ATA channel 1> [tentative] on atapci1
ata5: SATA connect time=0ms
ata5: reset tp1 mask=01 ostat0=50 ostat1=00
ata5: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata5: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ad8: type 0xa5, start 63, end = 976773167, size 976773105 : OK
ata5-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
No policy for ad10 specified, or policy not found
disk scheduler: set policy of ad10 to noop
ad10: Silicon Image check3 failed
ad10: Adaptec check1 failed
ad10: LSI (v3) check1 failed
ad10: LSI (v2) check1 failed
ad10: FreeBSD check1 failed
ad10: 476940MB <Seagate ST3500418AS CC38> at ata5-master SATA150
ad10: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
ata5: <ATA channel 1> [attached!] on atapci1
atapci1: <ATI IXP400 SATA150 controller> [attached!] port
0x8800-0x880f,0x9000-0x9003,0x9400-0x9407,0x9800-0x9803,0xa000-0xa007
mem 0xfe9fb800-0xfe9fb9ff irq 5 at device 18.0 on pci0
ohci0.pci0.pcib0.acpi0.nexus0.root0
ohci0: <ATI SB400 USB Controller> [tentative] mem
0xfe9fa000-0xfe9fafff irq 4 at device 19.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe9fa000
usb0: OHCI version 1.0, legacy support
sched_ithd: stray interrupt 7 on cpu 0
usb0: SMM does not respond, resetting
sched_ithd: stray interrupt 7 on cpu 0
sched_ithd: stray interrupt 7 on cpu 0
sched_ithd: stray interrupt 7 on cpu 0
usb0.ohci0.pci0.pcib0.acpi0.nexus0.root0
usb0: <ATI SB400 USB Controller> [tentative] on ohci0
usb0: USB revision 1.0
sched_ithd: stray interrupt 7 on cpu 0
sched_ithd: stray interrupt 7 on cpu 0
sched_ithd: stray interrupt 7 on cpu 0
uhub0.usb0.ohci0.pci0.pcib0.acpi0.nexus0.root0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb0
uhub0: 4 ports with 4 removable, self powered
sched_ithd: 10 stray interrupts 7 on cpu 0 - there will be no further reports
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb0
usb0: <ATI SB400 USB Controller> [attached!] on ohci0
ohci0: <ATI SB400 USB Controller> [attached!] mem
0xfe9fa000-0xfe9fafff irq 4 at device 19.0 on pci0
ohci1.pci0.pcib0.acpi0.nexus0.root0
ohci1: <ATI SB400 USB Controller> [tentative] mem
0xfe9f9000-0xfe9f9fff irq 4 at device 19.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe9f9000
usb1: OHCI version 1.0, legacy support
usb1.ohci1.pci0.pcib0.acpi0.nexus0.root0
usb1: <ATI SB400 USB Controller> [tentative] on ohci1
usb1: USB revision 1.0
uhub1.usb1.ohci1.pci0.pcib0.acpi0.nexus0.root0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb1
uhub1: 4 ports with 4 removable, self powered
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb1
usb1: <ATI SB400 USB Controller> [attached!] on ohci1
ohci1: <ATI SB400 USB Controller> [attached!] mem
0xfe9f9000-0xfe9f9fff irq 4 at device 19.1 on pci0
ehci0.pci0.pcib0.acpi0.nexus0.root0
ehci0: <ATI SB400 USB 2.0 controller> [tentative] mem
0xfe9f8000-0xfe9f8fff irq 4 at device 19.2 on pci0
ehci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe9f8000
ehci0: Dropped interrupts workaround enabled
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2.ehci0.pci0.pcib0.acpi0.nexus0.root0
usb2: <ATI SB400 USB 2.0 controller> [tentative] on ehci0
usb2: USB revision 2.0
uhub2.usb2.ehci0.pci0.pcib0.acpi0.nexus0.root0
uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [tentative] on usb2
uhub2: 8 ports with 8 removable, self powered
uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [attached!] on usb2
usb2: <ATI SB400 USB 2.0 controller> [attached!] on ehci0
ehci0: <ATI SB400 USB 2.0 controller> [attached!] mem
0xfe9f8000-0xfe9f8fff irq 4 at device 19.2 on pci0
pci0: <serial bus, SMBus> (vendor 0x1002, dev 0x4372) at device 20.0
atapci2.pci0.pcib0.acpi0.nexus0.root0
atapci2: <ATI IXP400 UDMA133 controller> [tentative] port
0xff00-0xff0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 20.1 on
pci0
atapci2: Reserved 0x10 bytes for rid 0x20 type 4 at 0xff00
ata0.atapci2.pci0.pcib0.acpi0.nexus0.root0
ata0: <ATA channel 0> [tentative] on atapci2
atapci2: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci2: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=01
ata0: stat0=0x10 err=0x01 lsb=0x14 msb=0xeb
ata0: stat1=0x01 err=0x04 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=10 stat1=01 devices=0x4<ATAPI_MASTER>
intr 5 at 19/20000 hz, livelock removed
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
acd0: setting PIO4 on IXP400 chip
acd0: setting UDMA66 on IXP400 chip
ad10: type 0xa5, start 63, end = 976773167, size 976773105 : OK
No policy for acd0 specified, or policy not found
disk scheduler: set policy of acd0 to noop
acd0: <SONY DVD RW DRU-830A/SS23> DVDR drive at ata0 as master
acd0: read 6890KB/s (6890KB/s) write 6890KB/s (6890KB/s), 2048KB buffer, UDMA66
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata0: <ATA channel 0> [attached!] on atapci2
ata1.atapci2.pci0.pcib0.acpi0.nexus0.root0
ata1: <ATA channel 1> [tentative] on atapci2
atapci2: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci2: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=7f ostat1=7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: reset tp2 stat0=ff stat1=ff devices=0x0
ata1: <ATA channel 1> [attached!] on atapci2
atapci2: <ATI IXP400 UDMA133 controller> [attached!] port
0xff00-0xff0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 20.1 on
pci0
pci0: <multimedia, HDA> (vendor 0x1002, dev 0x437b) at device 20.2 irq 5
isab0.pci0.pcib0.acpi0.nexus0.root0
isab0: <PCI-ISA bridge> [tentative] at device 20.3 on pci0
isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
isa0: <ISA bus> [tentative] on isab0
isa0: <ISA bus> [attached!] on isab0
isab0: <PCI-ISA bridge> [attached!] at device 20.3 on pci0
pcib2.pci0.pcib0.acpi0.nexus0.root0
pcib2: <ACPI PCI-PCI bridge> [tentative] at device 20.4 on pci0
pcib2:   domain            0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xe000-0xefff
pcib2:   memory decode     0xfeb00000-0xfebfffff
pcib2:   no prefetched decode
pcib2:   Subtractively decoded bridge.
ACPI: Found matching pin for 2.0.INTA at func 0: 255
ACPI: Found matching pin for 2.3.INTA at func 0: 255
pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
pci2: <ACPI PCI bus> [tentative] on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x1186, dev=0x4c00, revid=0x11
        domain=0, bus=2, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=255
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0, size 14, memory disabled
        map[14]: type I/O Port, range 32, base 0, size  8, port disabled
found-> vendor=0x10ec, dev=0x8169, revid=0x10
        domain=0, bus=2, slot=3, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
        intpin=a, irq=255
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type I/O Port, range 32, base 0, size  8, port disabled
        map[14]: type Memory, range 32, base 0, size  8, memory disabled
skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
skc0: <D-Link DGE-530T A1> [tentative] at device 0.0 on pci2
pcib2: skc0 requested memory range 0xfeb00000-0xfebfffff: good
skc0: Lazy allocation of 0x4000 bytes rid 0x10 type 3 at 0xfeb00000
pcib2: matched entry for 2.0.INTA (src \\_SB_.LNKE:0)
ICU: irq 15, edge -> level
pcib2: slot 0 INTA routed to irq 15 via \\_SB_.LNKE
sk0.skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
sk0: <Marvell Yukon (0x1)> [tentative] on skc0
sk0: bpf attached
sk0: MAC address: 00:11:95:f2:f2:4f
miibus0.sk0.skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
miibus0: <MII bus> [tentative] on sk0
e1000phy0.miibus0.sk0.skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
e1000phy0: <Marvell Semiconductor 88E1011 Gigabit PHY> [tentative] on miibus0
e1000phy0: 1000baseT-FDX, 100baseTX-FDX, 100baseTX, 10baseTX-FDX, 10baseTX, auto
e1000phy0: <Marvell Semiconductor 88E1011 Gigabit PHY> [attached!] on miibus0
miibus0: <MII bus> [attached!] on sk0
sk0: <Marvell Yukon (0x1)> [attached!] on skc0
skc0: <D-Link DGE-530T A1> [attached!] mem 0xfeb00000-0xfeb03fff irq
15 at device 0.0 on pci2
pcib2: re0 requested I/O range 0xe000-0xefff: in range
re0: Lazy allocation of 0x100 bytes rid 0x10 type 4 at 0xe000
re0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
re0: <RealTek 8110/8169 Gigabit Ethernet> [tentative] port
0xe000-0xe0ff at device 3.0 on pci2
pcib2: re0 requested I/O range 0xe000-0xe0ff: in range
pcib2: matched entry for 2.3.INTA (src \\_SB_.LNKE:0)
pcib2: slot 3 INTA routed to irq 15 via \\_SB_.LNKE
re0: Hardware rev. 0x10000000; MAC ver. 0x04; PCI32 33MHz
miibus1.re0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
miibus1: <MII bus> [tentative] on re0
rgephy0: rev: 2
rgephy0.miibus1.re0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0
rgephy0: <8211B/RTL8169S/8110S media interface> [tentative] on miibus1
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
rgephy0: <8211B/RTL8169S/8110S media interface> [attached!] on miibus1
miibus1: <MII bus> [attached!] on re0
re0: bpf attached
re0: MAC address: 00:16:17:20:2a:a6
re0: <RealTek 8110/8169 Gigabit Ethernet> [attached!] port
0xe000-0xe0ff irq 15 at device 3.0 on pci2
pci2: <ACPI PCI bus> [attached!] on pcib2
pcib2: <ACPI PCI-PCI bridge> [attached!] at device 20.4 on pci0
pci0: <ACPI PCI bus> [attached!] on pcib0
pcib0: <ACPI Host-PCI bridge> [attached!] port 0xcf8-0xcff on acpi0
acpi_button0.acpi0.nexus0.root0
acpi_button0: <Power Button> [tentative] on acpi0
acpi_button0: <Power Button> [attached!] on acpi0
unknown: not probed (disabled)
sio0: configured irq 3 not in bitmap of probed irqs 0
sio0: irq maps: 0 0 0 0
sio0.acpi0.nexus0.root0
sio0: <16550A-compatible COM port> [tentative] port 0x2f8-0x2ff irq 3 on acpi0
sio0: type 16550A
sio0: <16550A-compatible COM port> [attached!] port 0x2f8-0x2ff irq 3 on acpi0
fdc0.acpi0.nexus0.root0
fdc0: <NEC 72065B or clone> [tentative] port 0x3f7,0x3f0-0x3f5 irq 6
drq 2 on acpi0
fdc0: <NEC 72065B or clone> [attached!] port 0x3f7,0x3f0-0x3f5 irq 6
drq 2 on acpi0
ppc0: using extended I/O port range
ppc0: SPP
ppc0.acpi0.nexus0.root0
ppc0: <Standard parallel printer port> [tentative] port 0x378-0x37f
irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0.ppc0.acpi0.nexus0.root0
ppbus0: <Parallel port bus> [tentative] on ppc0
plip0.ppbus0.ppc0.acpi0.nexus0.root0
plip0: <PLIP network interface> [tentative] on ppbus0
lp0: bpf attached
plip0: <PLIP network interface> [attached!] on ppbus0
lpt0.ppbus0.ppc0.acpi0.nexus0.root0
lpt0: <Printer> [tentative] on ppbus0
lpt0: Interrupt-driven port
lpt0: <Printer> [attached!] on ppbus0
ppi0.ppbus0.ppc0.acpi0.nexus0.root0
ppi0: <Parallel I/O> [tentative] on ppbus0
ppi0: <Parallel I/O> [attached!] on ppbus0
ppbus0: <Parallel port bus> [attached!] on ppc0
ppc0: <Standard parallel printer port> [attached!] port 0x378-0x37f
irq 7 on acpi0
atkbdc0.acpi0.nexus0.root0
atkbdc0: <Keyboard controller (i8042)> [tentative] port 0x64,0x60 irq 1 on acpi0
atkbd0.atkbdc0.acpi0.nexus0.root0
atkbd0: <AT Keyboard> [tentative] flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
atkbd0: <AT Keyboard> [attached!] flags 0x1 irq 1 on atkbdc0
psm0: current command byte:0065
(probe0:ata4:0:0:0): error 22
(probe0:ata4:0:0:0): Unretryable Error
psm0.atkbdc0.acpi0.nexus0.root0
psm0: <PS/2 Mouse> [tentative] irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
psm0: <PS/2 Mouse> [attached!] irq 12 on atkbdc0
atkbdc0: <Keyboard controller (i8042)> [attached!] port 0x64,0x60 irq 1 on acpi0
cpu0.acpi0.nexus0.root0
cpu0: <ACPI CPU> [tentative] on acpi0
cpu_cst0.cpu0.acpi0.nexus0.root0
cpu_cst0: <ACPI CPU C-State> [tentative] on cpu0
cpu_cst0: switching to generic Cx mode
cpu_cst0: <ACPI CPU C-State> [attached!] on cpu0
cpu_pst0: Can't get _PCT package - AE_NOT_FOUND
cpu0: <ACPI CPU> [attached!] on acpi0
unknown: not probed (disabled)
acpi0: <A M I OEMRSDT> [attached!] at port
0x600-0x60f,0x10-0x1f,0x22-0x3f,0x62-0x63,0x65-0x6f,0x72-0x7f,0x80,0x84-0x86,0x88,0x8c-0x8e,0x90-0x9f,0xa2-0xbf,0xb1,0xe0-0xef,0x4d0-0x4d1,0x40b,0x4d6,0xc00-0xc01,0xc14,0xc50-0xc51,0xc52,0xc6c,0xc6f,0xcd4-0xcd5,0xcd6-0xcd7,0xcd8-0xcdf,0x800-0x89f,0x900-0x90f,0x910-0x91f
iomem 0-0x9ffff,0xc0000-0xcffff,0xe0000-0xfffff,0x100000-0x7fffffff,0xe0000000-0xefffffff,0xfec00000-0xfec00fff,0xfee00000-0xfee00fff,0xfff80000-0xffffffff
irq 9 on motherboard
fdc-: fdc0 exists, using next available unit number
atkbdc-: atkbdc0 exists, using next available unit number
sio-: sio0 exists, using next available unit number
sio-: sio1 exists, using next available unit number
sio-: sio2 exists, using next available unit number
sio-: sio3 exists, using next available unit number
ppc-: ppc0 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
aps_identify: will specify the port
ex_isa_identify()
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
orm0: <Option ROMs> [tentative] at iomem
0xc0000-0xcefff,0xcf000-0xd37ff,0xd3800-0xd7fff on isa0
orm0: <Option ROMs> [attached!] at iomem
0xc0000-0xcefff,0xcf000-0xd37ff,0xd3800-0xd7fff on isa0
pmtimer0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
pmtimer0 [tentative] on isa0
pmtimer0 [attached!] on isa0
fdc1: cannot reserve I/O port range
fdc1 [tentative] failed to probe at port 0x3f0 irq 6 drq 2 on isa0
adv0 [tentative] failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 [tentative] failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 [tentative] failed to probe at port 0x134-0x137 on isa0
aic0 [tentative] failed to probe at port 0x140-0x15f on isa0
atkbdc1: <Keyboard controller (i8042)> [tentative] failed to probe at
port 0x60 on isa0
vga0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
vga0: <Generic ISA VGA> [tentative] at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters to be used for mode 24
 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vga0: <Generic ISA VGA> [attached!] at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
sc0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
sc0: <System console> [tentative] at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sc0: <System console> [attached!] at flags 0x100 on isa0
aps0 [tentative] failed to probe at port 0x1600-0x161e on isa0
lm0 [tentative] failed to probe at port 0x290-0x297 on isa0
it0 [tentative] failed to probe at port 0x290-0x297 on isa0
it1 [tentative] failed to probe at port 0xc00-0xc07 on isa0
it2 [tentative] failed to probe at port 0xd00-0xd07 on isa0
it3 [tentative] failed to probe at port 0x228-0x22f on isa0
wbsio0 [tentative] failed to probe at port 0x2e-0x2f on isa0
wbsio1.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
wbsio1: <Winbond LPC Super I/O W83627THF rev 0x83> [tentative] at port
0x4e-0x4f on isa0
wbsio1: hardware monitor iobase is 0x600
wbsio1: found unused lm0 at 0x290 with state 0, reusing at 0x600
lm0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
lm0: <Winbond W83627THF Hardware Monitor> [tentative] at port
0x600-0x607 on isa0
lm0: <Winbond W83627THF Hardware Monitor> [attached!] at port
0x600-0x607 on isa0
wbsio1: <Winbond LPC Super I/O W83627THF rev 0x83> [attached!] at port
0x4e-0x4f on isa0
sio1: can't drain, serial port might not exist, disabling
sio1 [tentative] failed to probe at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio2 [tentative] failed to probe at port 0x2f8 irq 3 on isa0
sio3: not probed (disabled)
sio4: not probed (disabled)
ppc1: parallel port found at 0x378
ppc1: cannot reserve I/O port range
ppc1: <Parallel port> [tentative] failed to probe at port 0x378-0x37f
irq 7 on isa0
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
 1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
 2:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
 0 accounted for
Device configuration finished.
ndepotmags=4   x mag_cap=33  for nameibufs
ndepotmags=4   x mag_cap=33  for NFS mount
ndepotmags=4   x mag_cap=33  for NFS node
ndepotmags=4   x mag_cap=65  for vnodes
ndepotmags=4   x mag_cap=33  for UFS dirhash
faith0: bpf attached
lo0: bpf attached
ppp0: bpf attached
sl0: bpf attached
crypto: <crypto device>
CAM: Configuring bus: ata0
CAM: Configuring bus: ata1
CAM: Configuring bus: ata2
CAM: Configuring bus: ata3
CAM: Configuring bus: ata4
CAM: Configuring bus: ata5
CAM: Configuring 6 busses
CAM: Finished configuring bus: ata0
CAM: Finished configuring bus: ata1
CAM: Finished configuring bus: ata2
CAM: Finished configuring bus: ata3
CAM: Finished configuring bus: ata5
(probe0:ata4:0:0:0): error 6
(probe0:ata4:0:0:0): Unretryable Error
(probe0:ata4:0:0:0): error 22
(probe0:ata4:0:0:0): Unretryable Error
CAM: Finished configuring bus: ata4
CAM: finished configuring all busses
pass0 at ata4 bus 0 target 0 lun 0
pass0: <SONY DVD RW DRU-830A SS23> Removable CD-ROM SCSI-0 device
pass0: 66.000MB/s transfers
sg0 at ata4 bus 0 target 0 lun 0
sg0: <SONY DVD RW DRU-830A SS23> Removable CD-ROM SCSI-0 device
sg0: 66.000MB/s transfers
No policy for cd0 specified, or policy not found
disk scheduler: set policy of cd0 to noop
bootdev: a0200000 type=0 unit=0 slice=2 part=0 major=3
ATA PseudoRAID loaded
(cd0:ata4:0:0:0): error 6
(cd0:ata4:0:0:0): Unretryable Error
cd0 at ata4 bus 0 target 0 lun 0
cd0: <SONY DVD RW DRU-830A SS23> Removable CD-ROM SCSI-0 device
cd0: 66.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not
present - tray closed
Mounting root from ufs:/dev/ad4s1a
tryroot ad4s1a
Mounting devfs
start_init: trying /sbin/init
HAMMER(Backup1) recovery check seqno=7f32a788
HAMMER(Backup1) recovery range 300000000c51d360-300000000c51d360
HAMMER(Backup1) recovery nexto 300000000c51d360 endseqno=7f32a789
HAMMER(Backup1) mounted clean, no recovery needed
HAMMER(Backup2) recovery check seqno=4015f3e7
HAMMER(Backup2) recovery range 30000000079e8ad0-30000000079e8ad0
HAMMER(Backup2) recovery nexto 30000000079e8ad0 endseqno=4015f3e8
HAMMER(Backup2) mounted clean, no recovery needed
HAMMER(Backup3) recovery check seqno=057a7b4c
HAMMER(Backup3) recovery range 3000000017294e80-3000000017294e80
HAMMER(Backup3) recovery nexto 3000000017294e80 endseqno=057a7b4d
HAMMER(Backup3) mounted clean, no recovery needed
HAMMER(Bkpsrv2Backup1Slave) recovery check seqno=000f05c0
HAMMER(Bkpsrv2Backup1Slave) recovery range 3000000000075bb0-3000000000075bb0
HAMMER(Bkpsrv2Backup1Slave) recovery nexto 3000000000075bb0 endseqno=000f05c1
HAMMER(Bkpsrv2Backup1Slave) mounted clean, no recovery needed

Thanks :-)

--Siju




[Date Prev][Date Next]  [Thread Prev][Thread Next]  [Date Index][Thread Index]