DragonFly BSD
DragonFly users List (threaded) for 2006-11
[Date Prev][Date Next]  [Thread Prev][Thread Next]  [Date Index][Thread Index]

Re: mounting usb stick

From: "Ja'far Railton" <jrailton@xxxxxxxxxxxx>
Date: Sun, 12 Nov 2006 18:59:43 +0300

On Sat, Nov 11, 2006 at 06:45:34PM -0500, Justin C. Sherrill wrote:
> On Sat, November 4, 2006 5:37 am, Ja'far Railton wrote:
> > 	mount_msdos /dev/da0s1 /mnt
> >
> > Nothing happens. No output.
> >
> > <<detach it>>
> After mounting it, there's no output, but does it also not mount?  The
> diagnostic messages when mounting it look correct.  What is your
> motherboard?  It could be some strange revision of a normally-supported
> chipset.

No, it doesn't mount. After the mount command the cursor just hangs on the next line. ps ax | grep mount (on another terminal) shows:

  742  p0  DL+    0:00.00 mount_msdos /dev/da0s1 /mnt
  800  p2  RVL+   0:00.00 grep mount (tcsh)

Here's the dmesg (it's on a Thinkpad R30):

Copyright (c) 2003, 2004, 2005, 2006 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
DragonFly 1.6.0-RELEASE #3: Sun Jul 23 15:59:02 PDT 2006
TSC clock: 697401460 Hz, i8254 clock: 1193159 Hz
CPU: Intel Pentium III (697.42-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
real memory  = 259915776 (253824K bytes)
avail memory = 240025600 (234400K bytes)
Preloaded elf kernel "/kernel" at 0xc0736000.
Preloaded elf module "/modules/acpi.ko" at 0xc0736210.
Pentium Pro MTRR support enabled
md0: Malloc disk
pcibios: BIOS version 2.10
Using $PIR table, 10 entries at 0xc00fb9d0
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using MMX optimized bcopy/copyin/copyout
acpi0: <IBM TP-1C> on motherboard
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device.  You can't run both
acpi_timer0: <32-bit timer at 3.579545MHz> port 0xf108-0xf10b on acpi0
cpu0: <ACPI CPU (3 Cx states)> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_ec0: <Embedded Controller: GPE 0x22> port 0x66,0x62 on acpi0
legacypci0 on motherboard
pcib0: <Host to PCI bridge> on legacypci0
pci0: <PCI bus> on pcib0
agp0: <Ali Generic host to PCI bridge> mem 0xf0000000-0xf3ffffff at device 0.0 on pci0
agp0: bad initial aperture size, disabling
agp: cdevsw removed
device_probe_and_attach: agp0 attach returned 6
pcib1: <AcerLabs M5247 PCI-PCI(AGP Supported) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <Trident model 8620 VGA-compatible display device> at 0.0 irq 11
pci0: <unknown card> (vendor=0x10b9, dev=0x5451) at 6.0 irq 11
isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
fxp0: <Intel 82550 Pro/100 Ethernet> port 0x9000-0x903f mem 0x81a20000-0x81a3ffff,0x81a00000-0x81a00fff irq 11 at device 10.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: MAC address: 00:00:e2:56:c1:da
atapci0: <AcerLabs Aladdin ATA66 controller> port 0x7050-0x705f irq 15 at device 16.0 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <AcerLabs M15x3 Power Management Unit> at 17.0
cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 11 at device 19.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0x81e00000-0x81e00fff irq 10 at device 20.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: can't drain, serial port might not exist, disabling
sio1: can't drain, serial port might not exist, disabling
ppc0: cannot reserve I/O port range
pccard0: Allocation failed for cfe 32
pccard0: Allocation failed for cfe 33
sio4 at port 0x3e8-0x3ef irq 11 function 0 config 34 on pccard0
sio4: type 16550A
ad0: 38154MB <FUJITSU MHT2040AS> [77520/16/63] at ata0-master UDMA66
acd0: CDROM <CD-224E> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s2a
cd0 at ata1 bus 0 target 0 lun 0
cd0: <TEAC CD-224E 2.7B> Removable CD-ROM SCSI-0 device 
cd0: 16.000MB/s transfers
cd0: cd present [44747 x 2048 byte records]
ad0s4: rejecting partition in BSD label: it isn't entirely within the slice
ad0s4: start 25114383, end 78140159, size 53025777
ad0s4d: start 0, end 78140159, size 78140160
ad0s4: rejecting partition in BSD label: it isn't entirely within the slice
ad0s4e: start 63, end 12292559, size 12292497
ad0s4: rejecting partition in BSD label: it isn't entirely within the slice
ad0s4f: start 12292560, end 24509519, size 12216960
ad0s4: rejecting partition in BSD label: it isn't entirely within the slice
ad0s4i: start 24509583, end 25114319, size 604737
umass0: SanDisk Corporation U3 Cruzer Micro, rev 2.00/0.10, addr 2
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <SanDisk U3 Cruzer Micro 2.15> Removable Direct Access SCSI-2 device 
da0: 1.000MB/s transfers
da0: 973MB (1994385 512 byte sectors: 64H 32S/T 973C)



[Date Prev][Date Next]  [Thread Prev][Thread Next]  [Date Index][Thread Index]