DragonFly commits List (threaded) for 2009-06
DragonFly-220.127.116.11.g1980e master sys/dev/disk/ahci Makefile TODO ahci.c ahci.h ahci_cam.c ahci_pm.c atascsi.h
Author: Matthew Dillon <firstname.lastname@example.org>
Date: Wed Jun 10 23:24:06 2009 -0700
AHCI - Initial Port Multiplier support + misc fixes, and major reorg.
* Add nearly all of the core port multiplier support code. Add a
new module, ahci_pm.c, which has most of the PM support. Note
that the PM probe code (ahci_port_pmprobe()) was placed in ahci.c.
Note that we have to reduce the number of commands in the queue to 1
even though we are in command switched mode, which is contrary to the
AHCI spec which says we can queue more then 1 (the HBA still serializes
it). However, when I try to queue more then one to different devices
the SATA port gets fatal PHY errors.
* Significantly reorganize the hard and soft reset code and create
additional procedures in ahci_pm.c for hard and soft resets of
targets through the PM.
The softreset code now does the reset sequence twice to try to work
around an issue where a previous signature prevents the new signature
from being properly latched.
The hard and soft reset code and the CAM code now has a simple probe
sequencer using ap->ap_probe (and at->at_probe for the PM ata_port
* The hardreset code now interfaces with the PM probe code, which itself
is a bit complex. Ports with port multipliers on them can either busy
out on the initial probe or return information related to the device
at target 0 instead of information related to the PM itself, so we
have to probe the PM by putting the port into PMA mode and doing a
softreset of target 15 even if a PM does not appear to be attached.
* The hard and soft reset code for a target behind a PM (in ahci_pm.c)
tries to be careful not to break the entire port (and thus all the
targets) when one target misbehaves.
* Get a large chunk of the error handling code working with the PM,
including hopefully partial cancelation on target failure to fail
just that target instead of the entire SATA port.
* Modify the probe code to check for the presence of a PHY with a short
polling interval and skip the port if nothing appears to be connected
* Fix re-initialization recursions which can occur from the port interrupt
handler when called during a software or hardware reset.
* ATA_PORT vs AHCI_PORT
AHCI_PORT represents a physical port on the AHCI device. ATA_PORT
reprewents a logical port of which (if a PM is present) there can be
up to 16 per physical port. In most cases in the code we only pass
ATA_PORT (variable name 'atx') for targets behind a port multiplier
and we pass NULL for atx for directly connected targets. The variable
'at' is similar to 'atx' except it is always non-NULL and is a
pointer to target 0 on non-PM SATA ports (and the same as atx on
PM SATA ports).
* Reorganize tracking of ap->ap_active_cnt, tying it more directly to
the manipulation of ap->ap_active. This also fixed a few bugs in
the tracking of ap->ap_active_cnt.
* Implement the DHRS (Device-to-Host FIS) interrupt and properly
copy the rfis to the ccb. It is unclear whether command processing
stops when we receive DHRS but if it does we restart it. Without
this the PM register read and write functions do not work.
* Add interrupt code to track notification (SSNTF capability) via
the SDBS interrupt and AHCI_PREG_SNTF. Not tied into anything yet.
* Put all the bits for the AHCI_PREG_SERR register on the same plane,
combining the DIAG and ERR bits. Get rid of the shift-by-16 macros.
Summary of changes:
sys/dev/disk/ahci/Makefile | 2 +-
sys/dev/disk/ahci/TODO | 2 +-
sys/dev/disk/ahci/ahci.c | 1026 +++++++++++++++++++++++++++++++++---------
sys/dev/disk/ahci/ahci.h | 87 +++--
sys/dev/disk/ahci/ahci_cam.c | 472 +++++++++++---------
sys/dev/disk/ahci/ahci_pm.c | 466 +++++++++++++++++++
sys/dev/disk/ahci/atascsi.h | 36 +-
7 files changed, 1627 insertions(+), 464 deletions(-)
create mode 100644 sys/dev/disk/ahci/ahci_pm.c
DragonFly BSD source repository