DragonFly On-Line Manual Pages
DCONSCHAT(8) DragonFly System Manager's Manual DCONSCHAT(8)
NAME
dconschat -- user interface to dcons(4)
SYNOPSIS
dconschat [-brvwRT1] [-h hz] [-C console_port] [-G gdb_port] [-M core]
[-N system]
dconschat [-brvwR1] [-h hz] [-C console_port] [-G gdb_port] [-a address]
[-u bus_num] -t target_eui64
DESCRIPTION
The dconschat utility is designed to provide a way for users to access
dcons(4) (dumb console device) on a local or remote system. The
dconschat utility interacts with dcons(4) using kvm(3) or firewire(4),
and interacts with the user over TTY or TCP/IP. To access remote
dcons(4) using firewire(4), you have to specify target EUI64 address
using the -t option.
The dconschat utility and the dcons(4) driver communicate using 2 ports,
one for the console port and another for remote gdb(1) port. Users are
supposed to access dconschat using TTY, telnet(1) and gdb(1). You can
specify listen ports for console and gdb(1) port using the -C and -G
options respectively. The port number 0 has special meaning that current
TTY (stdin/stdout) is used instead of TCP/IP. A negative port number
will disable the port. To quit dconschat, send a CR + `~' + `.' sequence
to the console port, or send signal to the process.
By analogy with pty(4) device, the dcons(4) acts as a slave device and
dconschat acts as a master device with telnetd(8).
-b Translate Ctrl-C to ALT_BREAK (CR + `~' + Ctrl-B) on gdb(1) port.
-r Replay old buffer on connection.
-v Verbose debug output. Multiple -v options increase verbosity.
-w Listen on a wildcard address rather than localhost.
-R Read-only. Do not write anything to the dcons(4) buffer.
-T Enable ad-hoc workaround for the TELNET protocol to remove unnec-
essary byte sequences. It should be set when you access
dconschat using telnet(1).
-1 One-shot. Read available buffer, then exit. This implies the -r
option.
-h hz Specify polling rate. The default value is 100.
-C console_port
Specify the console port. The default value is 0 (stdin/stdout).
-G gdb_port
Specify gdb(1) port. The default value is -1 (disabled).
-M core
Specify core file.
-N system
Specify system file such as /boot/kernel.
-t target_eui64
Specify the 64-bit extended unique identifier of the target, and
use FireWire to access remote dcons(4).
-a address
Specify the physical I/O address of the dcons(4) buffer. See
dcons(4) for details. If this option is not specified, dconschat
tries to get the address from the Configuration ROM on the tar-
get. You are supposed to enable dcons_crom(4) on the target to
omit this option.
-u bus_num
Specify FireWire bus number. The default is 0.
FILES
/dev/fwmem0.0
/dev/mem
/dev/kmem
EXAMPLES
To use dconschat with FireWire for remote dcons(4), you have to specify
the EUI64 of the target. You can obtain EUI64 by running fwcontrol(8)
without options. The first EUI64 is of the host running fwcontrol(8) and
others on the bus follow.
# fwcontrol
2 devices (info_len=2)
node EUI64 status
1 77-66-55-44-33-22-11-00 0
0 00-11-22-33-44-55-66-77 1
The EUI64 does not change unless you change the hardware as the ethernet
address.
Now we can run dconschat.
# dconschat -br -G 12345 -t 00-11-22-33-44-55-66-77
You will get console output of the target and login prompt if a getty(8)
is running on dcons(4). You can break to DDB with ALT_BREAK (CR + `~' +
Ctrl-B) if DDB and ALT_BREAK_TO_DEBUGGER are enabled in the target ker-
nel. To quit the session, type CR + `~' + `.' in the console port.
Using gdb(1) port is almost the same as remote gdb(1) over serial line
except using TCP/IP instead of /dev/cu*. See On-line Kernel Debugging
Using Remote GDB section of The FreeBSD Developers Handbook and gdb(4)
for details.
% gdb -k kernel.debug
(kgdb) target remote :12345
Once gdb(1) is attached and you specified the -b option to dconschat,
typing Ctrl-C in gdb(1) causes a break to debugger.
The following command gets the console log from the crash dump:
# dconschat -1 -M vmcore.0 -N kernel.0
If you want access to the console using telnet(1), try the following:
# dconschat -rTC 5555 &
# telnet localhost 5555
You may want to keep logging console output of several machines.
conserver-com in the Ports collection may help you. Insert the following
lines in conserver.cf:
console local {
master localhost;
type exec;
exec /usr/sbin/dconschat -rh 25;
}
console remote {
master localhost;
type exec;
exec /usr/sbin/dconschat -rh 25 -t 00-11-22-33-44-55-66-77;
}
SEE ALSO
gdb(1), telnet(1), kvm(3), dcons(4), dcons_crom(4), ddb(4), firewire(4),
fwohci(4), gdb(4), eui64(5), fwcontrol(8)
AUTHORS
Hidetoshi Shimokawa <simokawa@FreeBSD.org>
BUGS
This utility is currently under development.
DragonFly 3.5 September 2, 2008 DragonFly 3.5