DragonFly On-Line Manual Pages


WRITE(2)		 DragonFly System Calls Manual		      WRITE(2)

NAME

write, writev, pwrite, pwritev -- write output

LIBRARY

Standard C Library (libc, -lc)

SYNOPSIS

#include <sys/types.h> #include <sys/uio.h> #include <unistd.h> ssize_t write(int d, const void *buf, size_t nbytes); ssize_t writev(int d, const struct iovec *iov, int iovcnt); ssize_t pwrite(int d, const void *buf, size_t nbytes, off_t offset); ssize_t pwritev(int d, const struct iovec *iov, int iovcnt, off_t offset);

DESCRIPTION

Write() attempts to write nbytes of data to the object referenced by the descriptor d from the buffer pointed to by buf. Writev() and pwritev() perform the same action, but gather the output data from the iovcnt buf- fers specified by the members of the iov array: iov[0], iov[1], ..., iov[iovcnt-1]. Pwrite() and pwritev() perform the same function, but write to the specified position in the file without modifying the file pointer. For writev() and pwritev(), the iovec structure is defined as: struct iovec { char *iov_base; /* Base address. */ size_t iov_len; /* Length. */ }; Each iovec entry specifies the base address and length of an area in mem- ory from which data should be written. Writev() and pwritev() will always write a complete area before proceeding to the next. On objects capable of seeking, the write() starts at a position given by the pointer associated with d, see lseek(2). Upon return from write(), the pointer is incremented by the number of bytes which were written. Objects that are not capable of seeking always write from the current position. The value of the pointer associated with such an object is undefined. If the real user is not the super-user, then write() clears the set-user- id bit on a file. This prevents penetration of system security by a user who ``captures'' a writable set-user-id file owned by the super-user. When using non-blocking I/O on objects such as sockets that are subject to flow control, write() and writev() may write fewer bytes than requested; the return value must be noted, and the remainder of the oper- ation should be retried when possible.

RETURN VALUES

Upon successful completion the number of bytes which were written is returned. Otherwise a -1 is returned and the global variable errno is set to indicate the error.

ERRORS

Write(), writev(), pwrite(), and pwritev() will fail and the file pointer will remain unchanged if: [EBADF] D is not a valid descriptor open for writing. [EPIPE] An attempt is made to write to a pipe that is not open for reading by any process. [EPIPE] An attempt is made to write to a socket of type SOCK_STREAM that is not connected to a peer socket. [EFBIG] An attempt was made to write a file that exceeds the process's file size limit or the maximum file size. [EFAULT] Part of iov or data to be written to the file points outside the process's allocated address space. [EINVAL] The pointer associated with d was negative. [ENOSPC] There is no free space remaining on the file system containing the file. [EDQUOT] The user's quota of disk blocks on the file system containing the file has been exhausted. [EIO] An I/O error occurred while reading from or writing to the file system. [EINTR] A signal interrupted the write before it could be com- pleted. [EAGAIN] The file was marked for non-blocking I/O, and no data could be written immediately. [EROFS] An attempt was made to write over a disk label area at the beginning of a disk. Use disklabel(8) -W to enable writing on the disk label area. In addition, writev() and pwritev() may return one of the following errors: [EDESTADDRREQ] The destination is no longer available when writing to a UNIX domain datagram socket on which connect(2) had been used to set a destination address. [EINVAL] Iovcnt was less than or equal to 0, or greater than UIO_MAXIOV. [EINVAL] One of the iov_len values in the iov array was nega- tive. [EINVAL] The sum of the iov_len values in the iov array over- flowed a 32-bit integer. [ENOBUFS] The mbuf pool has been completely exhausted when writ- ing to a socket. The pwrite() and pwritev() calls may also return the following errors: [EINVAL] The specified file offset is invalid. [ESPIPE] The file descriptor is associated with a pipe, socket, or FIFO.

SEE ALSO

fcntl(2), lseek(2), open(2), pipe(2), select(2)

STANDARDS

The write() function call is expected to conform to ISO/IEC 9945-1:1990 (``POSIX.1''). The writev() and pwrite() functions are expected to con- form to X/Open Portability Guide Issue 4, Version 2 (``XPG4.2'').

HISTORY

The pwritev() function call was added in DragonFly 1.5. The pwrite() function call appeared in AT&T System V Release 4 UNIX. The writev() function call appeared in 4.2BSD. A write() function call appeared in Version 6 AT&T UNIX. DragonFly 3.7 April 27, 2006 DragonFly 3.7