DragonFly On-Line Manual Pages
VMTOUCH(8) System Manager's Manual VMTOUCH(8)
NAME
vmtouch - the Virtual Memory Toucher
SYNOPSIS
vmtouch [OPTIONS] ... FILES OR DIRECTORIES ...
DESCRIPTION
Portable file system cache diagnostics and control.
vmtouch opens every file provided on the command line and maps it into
virtual memory with mmap(2). The mappings are opened read-only. It
recursively crawls any directories and does the same to all files it
finds within them.
With no options, vmtouch will not read from (touch) any memory pages.
It will only use mincore(2) to determine how many pages of each file
are actually resident in memory. Before exiting, it will print a
summary of the total pages encountered and how many were resident.
-t Touch virtual memory pages. Reads a byte from each page of the
file. If the page is not resident in memory, a page fault will be
generated and the page will be read from disk into the file
system's memory cache.
Note: Although each page is guaranteed to have been brought into
memory, the page might be evicted from memory by the time the
vmtouch command completes.
-e Evict the mapped pages from the file system cache. They will need
to be read in from disk the next time they are accessed. This is
the inverse of "-t".
Note: Even if the eviction is successful, pages may be paged back
into memory by the time the vmtouch command completes.
Note: This option is not portable to all systems. See PORTABILITY
below.
-l Lock pages into physical memory. This option works the same as "-t"
except it calls mlock(2) on all the memory mappings and doesn't
close the descriptors when finished. At the end of the crawl, if
successful, vmtouch will block indefinitely. The files will be
locked in physical memory until the vmtouch process is killed.
Note: While the vmtouch process is holding memory locks, any
processes that access the locked pages will not cause non-resident
page faults or address-translation faults although they may still
cause TLB misses.
Note: Because vmtouch holds file descriptors open it may reach the
"RLIMIT_NOFILE" process file descriptor limit. In this case it will
try to increase the descriptor limit which will only work if the
process is run with root privileges. Similarly, root privileges are
required to exceed the "RLIMIT_MEMLOCK" limit. Even with root
privileges, "-l" is limited by both the system file descriptor
limit and the system limit on "wired memory".
-L This option is the same as "-l" except that it uses mlockall(2) at
the end of the crawl rather than individually mlock(2)ing each
file. Because of this, other unrelated pages belonging to the
vmtouch process will also be locked in memory.
-d Daemon mode. After performing the crawl, disassociate from the
terminal and run in the background as a daemon. This option can
only be used with the "-l" or "-L" locking modes.
-m <max file size>
Maximum file size to map into virtual memory. Files that are larger
than this will be skipped. Examples: 4096, 4k, 100M, 1.5G. The
default is 500M.
-p <size range> or <size>
Page mode. Maps the portion of the file specified by a range
instead of the entire file. Size format same as for "-m". Omitted
range start (end) value means start (end) of file. Single <size>
value is equivalent to -<size>, i.e. map the first <size> bytes.
Examples: 4k-50k, 100M-2G, -5M, -.
-f Follow symbolic links. With this option, vmtouch will descend into
symbolic links that point to directories and will touch regular
files pointed to by symbolic links. Symbolic link loops are
detected and issue warnings.
-v Verbose mode. While crawling, print out every file being processed
along with its total number of pages and the number of its pages
that are currently resident in memory to standard output.
-q Quiet mode. Suppress the end of crawl summary and all warnings that
are normally printed to standard error. On success print nothing.
Fatal errors print a single error message line to standard error.
-h Normally, if multiple files both point to the same inode then
vmtouch will ignore all but the first it finds so as to avoid
double-counting their pages. This option overrides this behaviour
and double-counts anyways.
PORTABILITY
The page residency summaries depend on mincore(2) which first appeared
in 4.4BSD but is not present on all unix systems.
The "-l" and "-L" locking options depends on mlock(2) or mlockall(2),
both of which are specified by POSIX.1b-1993, Real-Time Extensions.
The "-e" page eviction option is the least portable. On Linux it uses
posix_fadvise(2) with "POSIX_FADV_DONTNEED" advice to inform the kernel
that the file should be evicted from the file system cache.
posix_fadvise(2) is specified by POSIX.1-2003 TC1. On FreeBSD, the
pages are invalidated with msync(2)'s "MS_INVALIDATE" flag. msync(2) is
specified by POSIX.1b-1993, Real-Time Extensions, although this call is
not required to remove pages from the file system cache. Some systems
like OpenBSD 4.3 don't have posix_fadvise(2), don't evict the pages on
an msync(2)/"MS_INVALIDATE", and don't evict the pages with
madvise(2)/"MADV_DONTNEED" so "-e" isn't supported on those systems
yet. Using "-e" on systems that don't yet support it is a fatal error.
SUPPORTED SYSTEMS
All vmtouch features have been confirmed to work on the following
systems:
Linux 2.6+
FreeBSD 4.X
FreeBSD 7.X
Solaris 10
OS X 10.x
HP-UX 11.31+patches (see below)
Systems that support everything except eviction:
OpenBSD 4.3
CPUs that have been tested:
x86
amd64 (x86-64)
SPARC
ARMv7
We would like to support as many systems as possible so please send us
any success reports, failure reports or patches. Thanks!
SYSTEM NOTES
Shane Seymour did the HP-UX port and says that either 32-bit or 64-bit
binaries can be compiled (just use "+DD64" for 64-bit). However,
mincore(2) was added to HP-UX 11.31 via patches and at least the
following patches need to be installed: PHKL_38651, PHKL_38708,
PHKL_38686, PHKL_38688, and PHCO_38658 (or patches that supersede those
ones).
SEE ALSO
Not all the following manual pages may exist in every unix dialect to
which vmtouch has been ported.
vmstat(8), touch(1), mmap(2), mincore(2), mlock(2), mlockall(2),
msync(2), madvise(2), posix_fadvise(2)
AUTHOR
Written by Doug Hoyte <doug@hcsw.org>
2015-12-04 VMTOUCH(8)