DragonFly On-Line Manual Pages
USBHID-UPS(8) NUT Manual USBHID-UPS(8)
NAME
usbhid-ups - Driver for USB/HID UPS equipment
NOTE
This man page only documents the hardware-specific features of the
usbhid-ups driver. For information about the core driver, see
nutupsdrv(8).
This driver, formerly called newhidups, replaces the legacy hidups
driver, which only supported Linux systems.
SUPPORTED HARDWARE
usbhid-ups brings USB/HID UPS monitoring to NUT on all platform
supporting USB through libusb. It should detect any UPS that uses the
HID power device class, but the amount of data will vary depending on
the manufacturer and model.
At the present time, usbhid-ups supports:
o the newer Eaton USB models,
o all MGE USB models,
o all Dell USB models,
o some APC models,
o some Belkin models,
o some Cyber Power Systems models,
o some Powercom models,
o some TrippLite models.
For a more complete list, refer to the NUT hardware compatibility list,
available in the source distribution as data/drivers.list, or on the
NUT website. You may use the "explore" driver option to gather
information from HID UPSes which are not yet supported; see below for
details.
This driver is known to work on:
o most Linux systems,
o FreeBSD (beta stage) and maybe other *BSD,
o Darwin / Mac OS X,
o Solaris 10.
EXTRA ARGUMENTS
This driver also supports the following optional settings:
offdelay=num
Set the timer before the UPS is turned off after the kill power
command is sent (via the -k switch).
The default value is 20 (in seconds). Usually this must be lower
than ondelay, but the driver will not warn you upon startup if it
isn't.
ondelay=num
Set the timer for the UPS to switch on in case the power returns
after the kill power command had been sent but before the actual
switch off. This ensures the machines connected to the UPS are, in
all cases, rebooted after a power failure.
The default value is 30 (in seconds). Usually this must be greater
than offdelay, but the driver will not warn you upon startup if it
isn't. Some UPS'es will restart no matter what, even if the power
is (still) out at the moment this timer elapses. In that case, you
could try if setting ondelay = -1 in ups.conf helps.
pollfreq=num
Set polling frequency, in seconds, to reduce the USB data flow.
Between two polling requests, the driver will wait for interrupts
(aka UPS notifications), which are data changes returned by the UPS
by itself. This mechanism allow to avoid or reduce staleness
message, due to the UPS being temporarily overloaded with too much
polling requests. The default value is 30 (in seconds).
pollonly
If this flag is set, the driver will ignore interrupts it receives
from the UPS (not recommended, but needed if these reports are
broken on your UPS).
vendor=regex, product=regex, serial=regex, vendorid=regex,
productid=regex
Select a specific UPS, in case there is more than one connected via
USB Each option specifies an extended regular expression (see
regex(7)) that must match the UPS's entire vendor/product/serial
string (minus any surrounding whitespace), or the whole 4-digit
hexadecimal code for vendorid and productid. Try -DD for finding
out the strings to match.
Examples:
o -x vendor="Foo.Corporation.*"
o -x vendorid=051d* (APC)
o -x product=".*(Smart|Back)-?UPS.*"
bus=regex
Select a UPS on a specific USB bus or group of busses. The argument
is a regular expression that must match the bus name where the UPS
is connected (e.g. bus="002", bus="00[2-3]").
explore
With this option, the driver will connect to any device, including
ones that are not yet supported. This must always be combined with
the "vendorid" option. In this mode, the driver will not do
anything useful except for printing debugging information
(typically used with -DD).
maxreport
With this option, the driver activates a tweak to workaround buggy
firmware returning invalid HID report length. Some APC Back-UPS
units are known to have this bug.
interruptonly
If this flag is set, the driver will not poll UPS. This also
implies using of INPUT flagged objects. Some Powercom units need
this option.
interruptsize=num
Limit the number of bytes to read from interrupt pipe. For some
Powercom units this option should be equal to 8.
INSTALLATION
This driver is not built by default. You can build it by using
"configure --with-usb=yes". Note that it will also install other USB
drivers.
You also need to install manually the legacy hotplug files (libhidups
and libhid.usermap, generally in /etc/hotplug/usb/), or the udev file
(nut-usbups.rules, generally in /etc/udev/rules.d/) to address the
permission settings problem. For more information, refer to the README
file in nut/scripts/hotplug or nut/scripts/udev.
On Linux with MGE equipment, you will need at least a 2.4.25 or 2.6.2
kernel as well as libusb-0.1.8 or later to disable hiddev support and
avoid conflict.
IMPLEMENTATION
The driver ignores the "port" value in ups.conf. Unlike previous
versions of this driver, it is now possible to control multiple UPS
units simultaneously with this driver, provided they can be
distinguished by setting some combination of the "vendor", "product",
"serial", "vendorid", and "productid" options. For instance:
[mge]
driver = usbhid-ups
port = auto
vendorid = 0463
[tripplite]
driver = usbhid-ups
port = auto
vendorid = 09ae
KNOWN ISSUES AND BUGS
Repetitive timeout and staleness
Some models tends to be unresponsive with the default polling
frequency. The result is that your system log will have lots of
messages like:
usb 2-1: control timeout on ep0in
usb 2-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 128 rq 6 len 256
ret -110
In this case, simply modify the general parameter "pollinterval" to a
higher value (like 10 for 10 seconds). This should solve the issue.
Got EPERM: Operation not permitted upon driver startup
You have forgotten to install the hotplug files, as explained in the
INSTALLATION section above. Don't forget to restart hotplug so that it
applies these changes.
Unattended shutdowns
The hardware which was used for development of this driver is almost
certainly different from what you have, and not all manufacturers
follow the USB HID Power Device Class specifications to the letter. You
don't want to find out that yours has issues here when a power failure
hits your server room and you're not around to manually restart your
servers.
If you rely on the UPS to shutdown your systems in case of mains
failure and to restart them when the power returns, you must test this.
You can do so by running upsmon -c fsd. With the mains present, this
should bring your systems down and then cycle the power to restart them
again. If you do the same without mains present, it should do the same,
but in this case, the outputs shall remain off until mains power is
applied again.
AUTHORS
Originally sponsored by MGE UPS SYSTEMS. Now sponsored by Eaton
http://opensource.eaton.com Arnaud Quette, Peter Selinger, Arjen de
Korte
SEE ALSO
The core driver
nutupsdrv(8)
Internet resources
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 2.7.3 04/17/2015 USBHID-UPS(8)