DragonFly On-Line Manual Pages

Search: Section:  


uftpd(1)               DragonFly General Commands Manual              uftpd(1)

NAME

uftpd - Encrypted UDP based ftp with multicast - client daemon

SYNOPSIS

uftpd [ -d ] [ -p port ] [ -B buf_size ] [ -E ] [ -Q dscp ] [ -U UID ] [ -x log_level ] [ -t ] [ -T temp_dir ] [ -D dest_dir[,dest_dir... ]] [ -A backup_dir[,backup_dir... ]] [ -L logfile ] [ -F status_file ] [ -q ] [ -P pidfile ] [ -S serverlist_file ] [ -R proxy[/fp] ] [ -c cache_size ] [ -k keyfile[,keyfile...] ] [ -K rsa:key_len | ec:curve[,rsa:key_len | ec:curve...]] [ -m ] [ -N priority ] [ -i ] [ -s postreceive_script ] [ -g max_log_size ] [ -n max_log_count ] [ -H hb_server[:port][,hb_server[:port]...] ] [ -h hb_interval ] [ -I interface[,interface...] ] [ -M pub_mcast_addr[,pub_mcast_addr...] ]

DESCRIPTION

uftpd is the client daemon of the UFTP suite. It listens on one or more multicast addresses to receive files from servers. This version of the client supports servers running UFTP 4.x.

OPTIONS

The following options are supported: -d Enable debug mode. The process will run in the foreground and all output will go to stderr. If specified, the -L option is ignored. -p port The UDP port number to listen on. Default is 1044. -U UID The unique ID for this client, specified as an 8 digit hexadecimal number (0xnnnnnnnn). The default value is based on the IP address of the first listed multicast capable interface on the system. If this address is IPv4, the UID is the address. If it is IPv6, the UID is the last 4 bytes of the address. -B buf_size The size in bytes of the UDP receive buffer to use. Valid values are 65536-104857600 (64KB-100MB). Defaults to 262144. -E Only allow incoming sessions if encryption is enabled. Default is to allow both encrypted and unencrypted sessions. -Q dscp Specifies the Differentiated Services Code Point (DSCP), formerly Type of Service (TOS), in the IP header for all outgoing packets. Valid values are 0-63 and may be specified in either decimal or hexadecimal. Default is 0. On Windows XP systems, the OS doesn't allow this parameter to be changed by default. To change this, add/modify the following DWORD registry value, set to 0, and reboot: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DisableUserTOSSetting Not currently supported on Windows Vista or later. -x log_level Specifies current logging level. Valid values are 0-5, with 0 being the least verbose and 5 being the most verbose. Default is 2, which is consistent with logging prior to version 3.5. -t Receive each file into a temp file in the same directory as the destination file. The temp file will have an extension of .~uftp-{group-id}-{file-id}, where {group-id} and {file-id} are the group ID of the current session and file ID of the current file. If -A is also specified, the existing destination file is not moved to backup directory until after the file is fully received. -T temp_dir Temp directory in which files are received, then moved to dest_dir when the session is complete. If omitted, files are received directly into dest_dir. Must reside on the same filesystem as the destination directory. The -T option MUST be specified to allow the client to save the state of failed file transfers that can be resumed later. Not compatible -A or -t. Not compatible with -D when multiple destination directories are specified. Also, no incoming files with an absolute path will be accepted if this option is specified. IMPORTANT: When full directories are received, the entire directory is moved at once to the destination directory, removing any existing file/directory. This means that if an existing directory in dest_dir is the same name as a directory received into temp_dir, all files under the existing directory are deleted. The -i option prevents by moving all files individually. -D dest_dir[,dest_dir...] Destination directories for all received files. When an incoming file specifies an absolute path, it must match one of the destination directories, otherwise the file will be rejected. Incoming files that don't specify an absolute path will be received into the first destination directory in the list. Default is /tmp for UNIX-like systems, C:\temp for Windows. -A backup_dir[,backup_dir...] Specifies backup directories. Each backup directory corresponds to a destination directory, so the number of each MUST be the same. Existing files that would be overwritten by incoming files are moved to the corresponding backup directory for the selected destination directory, first under timestamped directories, then under the full path of the existing file. For example, if /full/path/to/file would be overwritten, it is moved to {backup_dir}/YYYYMMDD/HHMMSS/full/path/to/file. Under Windows, drive letters for local files are not part of the name, but host/share names for network files are. So C:\path\to\file would be backed up to {backup_dir}\YYYYMMDD\HHMMSS\path\to\file, and \\host\share\path\to\file would be backed up to {backup_dir}\YYYYMMDD\HHMMSS\host\share\path\to\file. Not compatible with -T. -L logfile Specifies the log file. Default is /tmp/uftpd.log for UNIX-like systems systems, C:\uftpd_log.txt for Windows. -F status_file Prints easily parsable status information to a file. Setting this option to @LOG results in status info being mixed with normal logging output. The following is printed when the client registers with a server: CONNECT;timestamp;server_id;session_id;server_ip;server_name Where "timestamp" is the time in yyyy/mm/dd-hh:mm:ss format, "server_id" is the ID of the server, "session_id" is the ID of the session with the server, "server_ip" is the IP address that the server message came from, and "server_name" is the name associated with server_ip. The following is printed after each file: RESULT;timestamp;server_id;session_id;filename;size;status Where "timestamp" is the time in yyyy/mm/dd-hh:mm:ss format, "server_id" is the ID of the server, "session_id" is the ID of the session with the server, "filename" is the name of the current file, "size" is the size of the file in kilobytes (i.e. 1234KB), and status is: copy: The file was received. overwrite: The file was received, and overwrote an existing file. Only generated in sync mode. skipped: The file was declined because it is older that the existing file. Only generated in sync mode. rejected: The file was rejected, because the file was sent with an absolute pathname and either the client is using a temp directory or the filename doesn't match one of the client's destination directories. -q When the client receives an ANNOUNCE from the server, it normally print the hostname associated with the IP address where the ANNOUNCE came from. Specifying this option prevents a DNS lookup of the server IP, saving time. -P pidfile The pidfile to write the daemon's pid to on startup. Default is no pidfile. -S serverlist_file A file containing a list of servers the client will allow to send files to it. The file should contain the ID of the server, the IP address the client expects the server's request to come from, and optionally the server's public key fingerprint, with one entry for a server on each line. If a key fingerprint is given, the key specified by the server must match the fingerprint. If your system supports source specific multicast (SSM), the client will subscribe to all public and private multicast addresses using SSM for all servers listed. When this option is specified, the public and private addresses specified by the server must be valid SSM addresses. Any ANNOUNCE that specifies a private IP that is not a valid SSM address will be rejected. Valid SSM addresses are in the 232/8 range for IPv4 and the ff30::/96 range for IPv6. Example contents: 0x11112222|192.168.1.101|66:1E:C9:1D:FC:99:DB:60:B0:1A:F0:8F:CA:F4:28:27:A6:BE:94:BC 0x11113333|fe80::213:72ff:fed6:69ca When expecting to receive from a server that is behind a proxy, the file should list the ID of the server along with the IP and fingerprint of the client proxy. The proxy can authenticate the server. -R proxy[/fingerprint] Specifies the name/IP of the response proxy that all responses are forwarded to. If fingerprint is given, it specifies the proxy's public key fingerprint. Upon startup, the client will query the proxy for its public key, retrying every 5 seconds until it gets a successful response. The client cannot accept an encrypted file transfer from a server until it gets the proxy's key. -c cache_size Specifies the size in bytes of the cache used to hold received data packets before they are written to disk. Proper tuning of this value can greatly increase efficiency at speeds in the gigabit range. Valid values are 10240-20971520 (10KB-20MB). Default is 1048576 (1MB). -k keyfile[,keyfile...] -K rsa:key_length | ec:curve[,rsa:key_length | ec:curve...] These two options are used to read and/or write the client's RSA/ECDSA private keys. The -K option creates one or more RSA or ECDSA private keys. New keys are specified as either rsa:key_length, which creates an RSA private key key_length bits wide, or as ec:curve, which creates an EC key using the curve "curve". The list of supported EC curves is as follows (availability may vary depending on system settings and crypto library used): sect163k1 sect163r1 sect163r2 sect193r1 sect193r2 sect233k1 sect233r1 sect239k1 sect283k1 sect283r1 sect409k1 sect409r1 sect571k1 sect571r1 secp160k1 secp160r1 secp160r2 secp192k1 prime192v1 secp224k1 secp224r1 secp256k1 prime256v1 secp384r1 secp521r1 If only -K is specified, the keys created are not persisted. If only -k is specified, this option reads RSA or ECDSA private keys from each keyfile. If -k and -K are specified, the keys created by -K are written to the keyfiles listed by -k. In this case, -k and -K must give the same number of items. If neither -k nor -K are specified, an RSA private key 512 bytes in length is generated and not persisted. If -k is specified but not -K, the RSA or ECDSA private keys are read from each keyfile. The definition of keyfile is dependent on the crypto library UFTP is compiled to use. On Windows systems, UFTP can built to use either CNG, which is the new API supported by Windows Vista and Windows 7, or CryptoAPI, which is the legacy API and the only one available to Windows XP. Under CryptoAPI, all RSA private keys must be stored in a key container (technically only keys used to sign data, but for UFTP's purposes this is the case). Key containers are internal to Windows, and each user (and the system) has its own set of key containers. In this case, key_file is actually the name of the key container. When -k is not specified, the generated key is not persisted. Elliptic Curve algorithms are not supported under CryptoAPI. Under CNG, RSA and ECDSA private keys are also stored in key containers, and RSA keys created by CrypoAPI may be read by CNG. Like CryptoAPI, key_file also specifies the key container name, and the generated key is not persisted if -k is not specified. CNG only supports 3 named EC curves: prime256v1, secp384r1, and secp521r1. All other systems use OpenSSL for the crypto library (although under Windows UFTP can be also be built to use it). In this case, key_file specifies a file name where the RSA private key is stored unencrypted in PEM format (the OS is expected to protect this file). When both -k and -K are specified, the file is only written to if it does not currently exist. If the file does exist, an error message will be returned and the server will exit. When -k is not specified, the generated key is not persisted. These PEM files may also be manipulated via the openssl(1) command line tool. Keys can also be generated and viewed via the uftp_keymgt(1) utility. -m For Windows systems using CryptoAPI or CNG, private keys are normally stored in the key container of the running user. Specifying this option stores keys in the system key container. Useful when running as a service. On non-Windows systems, this option has no effect. -N priority Sets the process priority. On Windows systems, valid values are from -2 to 2, with a default of 0. These correspond to the following priorities: -2 High -1 Above Normal 0 Normal 1 Below Normal 2 Low On all other systems, this is the "nice" value. Valid values are from -20 to 19, where -20 is the highest priority and 19 is the lowest priority. Default is 0. -i When -T is specified, directories are normally moved from the temp directory to the destination directory at once, removing all existing files in the that subdirectory within the destionaion directory. This option causes directories to be traversed so that all received files are moved individually, preventing unwanted deletions. This also affects the operation of the -s option. If -T is not specified, this option has no effect. -s postreceive_script The full path to an external command or script to be called when files are received. The command will be called as follows: postreceive_script -I session_id file [ file... ] Where "session_id" is an 8 hexadecimal digit number identifying the current session, and "file" is the full pathname to one or more received files/directories in the destination directory specified by -D. The way this script is called depends on whether or not a temp directory is specified by -T, and if -i is specified. If a temp directory is not specified, or if both -T and -i are specified, the script gets called once for each file as soon as the file is received. If a temp directory is specified but -i is not, the script gets called once at the end of the session, and is passed all top level files/directories received. Here, "top level files/directories" refers to all entries in the temp directory for the session, but not subdirectories. So the script would be responsible for traversing any listed directories to find files contained within them. -g max_log_size Specifies the maximum log file size in MB. Once the log file reaches this size, the file is renamed with a .1 extension and a new log file is opened. For example, if the log file is /tmp/uftpd.log, it will be renamed /tmp/uftpd.log.1 and a new /tmp/uftpd.log will be created. Ignored if -d is specified. Valid values are 1-1024. Default is no log rolling. -n max_log_count Specifies the maximum number of archive log files to keep when log rolling is active. When the log file rolls, archive logs are renamed with an incrementing numerical extension until the max is reached. Archive log files beyond the maximum are deleted. Ignored if -g is not specified. Valid values are 1-1000. Default is 5. -H hb_server[:port][,hb_server[:port]...] Lists one or more proxies to send heartbeat messages to. When sending a signed heartbeat message, the first key listed under -k is used to sign the message. If port is not specified for a given proxy, the default port of 1044 is assumed. -h hb_interval The time in seconds between sending heartbeat messages. Ignored if -H is not specified. -I interface[,interface...] Lists one or more interfaces to listen to multicast traffic on. Interfaces can be specified either by interface name, by hostname, or by IP. When receiving a closed group membership request, the client will participate if any of these interfaces matches an IP in the announcement. When receiving an open group membership request, the first interface listed is the one the client will report back to the server. This may not necessarily be the interface that the ANNOUNCE was received on. The default is to listen on all active non-loopback interfaces. NOTE: Since Windows doesn't have named interfaces (not in the sense that UNIX-like systems do), only hostnames or IP addresses are accepted on Windows. If specifying by hostname or IP, may be a mixture of IPv4 and IPv6 addresses, except on systems that don't support dual mode sockets such as Windows XP. -M pub_multicast_addr[,pub_multicast_addr...] The list of public multicast addresses to listen on. May be a mixture of IPv4 and IPv6 addresses, except on systems that don't support dual mode sockets such as Windows XP. Default is 230.4.4.1

EXAMPLES

Starting with the default options: uftpd The client runs as a daemon and listens for announcements on UDP port 1044 on multicast address 230.4.4.1 on all non-loopback network interfaces. Incoming files are received directly into /tmp (C:\temp on Windows). A 512-bit RSA key is generated to handle encrypted sessions. Suppose you want an external process to handle incoming files in /tmp/dest. Since you don't want to pick up incomplete files, you might want them to be received into /tmp/receiving then moved to /tmp/dest when done. Then call the client like this: uftpd -D /tmp/dest -T /tmp/receiving If the client expects to receive from different servers, one sending on 230.4.4.1 and one sending on ff02:4:4:2: uftpd -M 230.4.4.1,ff02:4:4:2 To handle incoming encrypted sessions with differing private keys: uftpd -k file_for_rsa_1024_key,file_for_rsa_2048_key,file_for_ec_prime256v1_key If incoming packets aren't being read quickly enough, and you want to increase the UDP receive buffer size to 2 MB: uftpd -B 2097152

EXIT STATUS

The following exit values are returned: 0 The client started successfully and is running in the background. 1 An invalid command line parameter was specified. 2 An error occurred while attempting to initialize network connections. 3 An error occurred while reading or generating cryptographic key data. 4 An error occurred while opening or rolling the log file. 5 A memory allocation error occurred. 6 The client was interrupted by the user.

SEE ALSO

uftp(1), uftpproxyd(1), uftp_keymgt(1)

NOTES

The latest version of UFTP can be found at http://uftp- multicast.sourceforge.net. UFTP is covered by the GNU General Public License. Commercial licenses and support are available from Dennis Bush (bush@tcnj.edu). UFTP 4.8 5 January 2016 uftpd(1)

Search: Section: