DragonFly On-Line Manual Pages
SIS(4) DragonFly Kernel Interfaces Manual SIS(4)
NAME
sis - SiS 900, SiS 7016 and NS DP83815 fast ethernet device driver
SYNOPSIS
device miibus
device sis
DESCRIPTION
The sis driver provides support for PCI ethernet adapters and embedded
controllers based on the Silicon Integrated Systems SiS 900 and SiS 7016
fast ethernet controller chips, as well as support for adapters based on
the National Semiconductor DP83815 (MacPhyter) PCI ethernet controller
chip, including the Netgear FA311-TX and FA312-TX.
The SiS 900 is a 100Mbps ethernet MAC and MII-compliant transceiver in a
single package. It uses a bus master DMA and a scatter/gather descriptor
scheme. The SiS 7016 is similar to the SiS 900 except that it has no
internal PHY, requiring instead an external transceiver to be attached to
its MII interface. The SiS 900 and SiS 7016 both have a 128-bit
multicast hash filter and a single perfect filter entry for the station
address.
The NS DP83815 is also a 100Mbps ethernet MAC with integrated PHY. The
NatSemi chip and the SiS 900 share many of the same features and a fairly
similar programming interface, hence both chips are supported by the same
driver.
The sis driver supports the following media types:
autoselect Enable autoselection of the media type and options. The
user can manually override the autoselected mode by adding
media options to rc.conf(5).
10baseT/UTP Set 10Mbps operation. The ifconfig(8) mediaopt option can
also be used to select either `full-duplex' or `half-duplex'
modes.
100baseTX Set 100Mbps (fast ethernet) operation. The ifconfig(8)
mediaopt option can also be used to select either
`full-duplex' or `half-duplex' modes.
The sis driver supports the following media options:
full-duplex Force full duplex operation
half-duplex Force half duplex operation.
For more information on configuring this device, see ifconfig(8). The
sis driver supports polling(4).
DIAGNOSTICS
sis%d: couldn't map ports/memory A fatal initialization error has
occurred.
sis%d: couldn't map interrupt A fatal initialization error has occurred.
sis%d: watchdog timeout The device has stopped responding to the
network, or there is a problem with the network connection (e.g. a cable
fault).
sis%d: no memory for rx list The driver failed to allocate an mbuf for
the receiver ring.
sis%d: no memory for tx list The driver failed to allocate an mbuf for
the transmitter ring when allocating a pad buffer or collapsing an mbuf
chain into a clusisr.
sis%d: chip is in D3 power state -- setting to D0 This message applies
only to adapters which support power management. Some operating systems
place the controller in low power mode when shutting down, and some PCI
BIOSes fail to bring the chip out of this state before configuring it.
The controller loses all of its PCI configuration in the D3 state, so if
the BIOS does not set it back to full power mode in time, it will not be
able to configure it correctly. The driver tries to detect this
condition and bring the adapter back to the D0 (full power) state, but
this may not be enough to return the driver to a fully operational
condition. If you see this message at boot time and the driver fails to
attach the device as a network interface, you will have to perform a warm
boot to have the device properly configured.
Note that this condition only occurs when warm booting from another
operating system. If you power down your system prior to booting
DragonFly, the card should be configured correctly.
SEE ALSO
arp(4), ifmedia(4), miibus(4), netintro(4), ng_ether(4), polling(4),
ifconfig(8)
SiS 900 and SiS 7016 datasheets, http://www.sis.com.tw.
NatSemi DP83815 datasheet, http://www.national.com.
HISTORY
The sis device driver first appeared in FreeBSD 3.0.
AUTHORS
The sis driver was written by Bill Paul <wpaul@ee.columbia.edu>.
DragonFly 5.9-DEVELOPMENT September 4, 1999 DragonFly 5.9-DEVELOPMENT