DragonFly On-Line Manual Pages

SCAN_FFS(8)            DragonFly System Manager's Manual           SCAN_FFS(8)

NAME
     scan_ffs - find UFS/FFS partitions on a disk

SYNOPSIS
     scan_ffs [-lsv] [-b begin] [-e end] device

DESCRIPTION
     This is the life-saver of typos.  If you have ever been working too long,
     and just happened to type 'disklabel -rw da0 floppy', instead of
     'disklabel -rw fd0 floppy', you know what I am talking about.

     This little program will take a raw disk device (which you might have to
     create) that covers the whole disk, and finds all probable UFS/FFS
     partitions on the disk.  It has various options to make it go faster, and
     to print out information to help in the reconstruction of the disklabel.

     The options are as follows:

     -l      This will make scan_ffs print out a string looking much like the
             input to disklabel.  With a little massaging, this output can
             usually be used in the disklabel edit.

     -s      This tells scan_ffs to be smart about skipping partitions (when
             it thinks it found a valid one).  By not scanning partitions for
             superblocks, the program completes a couple of orders of
             magnitude faster.  However, sometimes being smart is too good for
             its own good, especially if your disk has had a different layout
             previously, or contains other non-UFS/FFS filesystems.

     -v      Tell scan_ffs to be verbose about what it is doing, and what it
             has found.

     -b begin
             Tell scan_ffs where to begin searching for filesystems.  This
             makes it easier to skip swap partitions, or other large non-
             UFS/FFS partitions.

     -e end  Ditto for telling scan_ffs where to stop.

     device  This specifies which device scan_ffs should use to scan for
             filesystems.  Usually this device should cover the whole disk in
             question.

     The basic operation of this program is as follows:

     1.    Panic.  You usually do so anyways, so you might as well get it over
           with.  Just don't do anything stupid.  Panic away from your
           machine.  Then relax, and see if the steps below won't help you
           out.

     2.    Try to find your old disklabel by any other means possible.  This
           includes printouts, backups, screendumps, and whatever other method
           you can think of.  The more information you have, the better your
           chances are in recovering the disklabel of the disk.

     3.    Create a disklabel on the affected disk, which covers the whole
           disk, and has at least one partition which covers the whole disk.
           As the "c" partition usually covers the whole disk anyways, this
           sounds like a good place to start.

     4.    Run scan_ffs over this partition.  If you have any information
           about the disklabel which used to exist on the disk, keep that in
           mind while scan_ffs spews out its things.

     5.    Use disklabel(8) to reconstruct the disklabel on the affected disk,
           using all the information you gathered from scan_ffs and other
           sources.

     Last but certainly not least, we wish you good luck.  The UFS/FFS
     filesystems are pretty sturdy.  I've seen them reconstructed after some
     pretty weird and awesome fumbles.  If you can't have backups, at least
     have funky tools to help you out of a jam when they happen.

SEE ALSO
     disklabel(8)

HISTORY
     The scan_ffs utility first appeared in OpenBSD 2.3 and was ported to
     FreeBSD by Robert Watson. UFS2 Support was added by Michael Ranner.

BUGS
     It is not perfect, and could do a lot more things with date/time
     information in the superblocks it finds, but this program has saved more
     than one butt, more than once.

DragonFly 6.5-DEVELOPMENT      January 31, 1998      DragonFly 6.5-DEVELOPMENT