DragonFly On-Line Manual Pages
AVCONV(1) AVCONV(1)
avconv - avconv video converter
avconv [global options] [[infile options][-i infile]]... {[outfile
options] outfile}...
avconv is a very fast video and audio converter that can also grab from
a live audio/video source. It can also convert between arbitrary sample
rates and resize video on the fly with a high quality polyphase filter.
avconv reads from an arbitrary number of input "files" (which can be
regular files, pipes, network streams, grabbing devices, etc.),
specified by the "-i" option, and writes to an arbitrary number of
output "files", which are specified by a plain output filename.
Anything found on the command line which cannot be interpreted as an
option is considered to be an output filename.
Each input or output file can in principle contain any number of
streams of different types (video/audio/subtitle/attachment/data).
Allowed number and/or types of streams can be limited by the container
format. Selecting, which streams from which inputs go into output, is
done either automatically or with the "-map" option (see the Stream
selection chapter).
To refer to input files in options, you must use their indices
(0-based). E.g. the first input file is 0, the second is 1 etc.
Similarly, streams within a file are referred to by their indices. E.g.
"2:3" refers to the fourth stream in the third input file. See also the
Stream specifiers chapter.
As a general rule, options are applied to the next specified file.
Therefore, order is important, and you can have the same option on the
command line multiple times. Each occurrence is then applied to the
next input or output file. Exceptions from this rule are the global
options (e.g. verbosity level), which should be specified first.
Do not mix input and output files -- first specify all input files,
then all output files. Also do not mix options which belong to
different files. All options apply ONLY to the next input or output
file and are reset between files.
o To set the video bitrate of the output file to 64kbit/s:
avconv -i input.avi -b 64k output.avi
o To force the frame rate of the output file to 24 fps:
avconv -i input.avi -r 24 output.avi
o To force the frame rate of the input file (valid for raw formats
only) to 1 fps and the frame rate of the output file to 24 fps:
avconv -r 1 -i input.m2v -r 24 output.avi
The format option may be needed for raw input files.
The transcoding process in avconv for each output can be described by
the following diagram:
_______ ______________
| | | |
| input | demuxer | encoded data | decoder
| file | ---------> | packets | -----+
|_______| |______________| |
v
_________
| |
| decoded |
| frames |
|_________|
________ ______________ |
| | | | |
| output | <-------- | encoded data | <----+
| file | muxer | packets | encoder
|________| |______________|
avconv calls the libavformat library (containing demuxers) to read
input files and get packets containing encoded data from them. When
there are multiple input files, avconv tries to keep them synchronized
by tracking lowest timestamp on any active input stream.
Encoded packets are then passed to the decoder (unless streamcopy is
selected for the stream, see further for a description). The decoder
produces uncompressed frames (raw video/PCM audio/...) which can be
processed further by filtering (see next section). After filtering the
frames are passed to the encoder, which encodes them and outputs
encoded packets again. Finally those are passed to the muxer, which
writes the encoded packets to the output file.
Filtering
Before encoding, avconv can process raw audio and video frames using
filters from the libavfilter library. Several chained filters form a
filter graph. avconv distinguishes between two types of filtergraphs -
simple and complex.
Simple filtergraphs
Simple filtergraphs are those that have exactly one input and output,
both of the same type. In the above diagram they can be represented by
simply inserting an additional step between decoding and encoding:
_________ ______________
| | | |
| decoded | | encoded data |
| frames |\ /| packets |
|_________| \ / |______________|
\ __________ /
simple \ | | / encoder
filtergraph \| filtered |/
| frames |
|__________|
Simple filtergraphs are configured with the per-stream -filter option
(with -vf and -af aliases for video and audio respectively). A simple
filtergraph for video can look for example like this:
_______ _____________ _______ ________
| | | | | | | |
| input | ---> | deinterlace | ---> | scale | ---> | output |
|_______| |_____________| |_______| |________|
Note that some filters change frame properties but not frame contents.
E.g. the "fps" filter in the example above changes number of frames,
but does not touch the frame contents. Another example is the "setpts"
filter, which only sets timestamps and otherwise passes the frames
unchanged.
Complex filtergraphs
Complex filtergraphs are those which cannot be described as simply a
linear processing chain applied to one stream. This is the case e.g.
when the graph has more than one input and/or output, or when output
stream type is different from input. They can be represented with the
following diagram:
_________
| |
| input 0 |\ __________
|_________| \ | |
\ _________ /| output 0 |
\ | | / |__________|
_________ \| complex | /
| | | |/
| input 1 |---->| filter |\
|_________| | | \ __________
/| graph | \ | |
/ | | \| output 1 |
_________ / |_________| |__________|
| | /
| input 2 |/
|_________|
Complex filtergraphs are configured with the -filter_complex option.
Note that this option is global, since a complex filtergraph by its
nature cannot be unambiguously associated with a single stream or file.
A trivial example of a complex filtergraph is the "overlay" filter,
which has two video inputs and one video output, containing one video
overlaid on top of the other. Its audio counterpart is the "amix"
filter.
Stream copy
Stream copy is a mode selected by supplying the "copy" parameter to the
-codec option. It makes avconv omit the decoding and encoding step for
the specified stream, so it does only demuxing and muxing. It is useful
for changing the container format or modifying container-level
metadata. The diagram above will in this case simplify to this:
_______ ______________ ________
| | | | | |
| input | demuxer | encoded data | muxer | output |
| file | ---------> | packets | -------> | file |
|_______| |______________| |________|
Since there is no decoding or encoding, it is very fast and there is no
quality loss. However it might not work in some cases because of many
factors. Applying filters is obviously also impossible, since filters
work on uncompressed data.
By default avconv tries to pick the "best" stream of each type present
in input files and add them to each output file. For video, this means
the highest resolution, for audio the highest channel count. For
subtitle it's simply the first subtitle stream.
You can disable some of those defaults by using "-vn/-an/-sn" options.
For full manual control, use the "-map" option, which disables the
defaults just described.
All the numerical options, if not specified otherwise, accept in input
a string representing a number, which may contain one of the SI unit
prefixes, for example 'K', 'M', 'G'. If 'i' is appended after the
prefix, binary prefixes are used, which are based on powers of 1024
instead of powers of 1000. The 'B' postfix multiplies the value by 8,
and can be appended after a unit prefix or used alone. This allows
using for example 'KB', 'MiB', 'G' and 'B' as number postfix.
Options which do not take arguments are boolean options, and set the
corresponding value to true. They can be set to false by prefixing with
"no" the option name, for example using "-nofoo" in the command line
will set to false the boolean option with name "foo".
Stream specifiers
Some options are applied per-stream, e.g. bitrate or codec. Stream
specifiers are used to precisely specify which stream(s) does a given
option belong to.
A stream specifier is a string generally appended to the option name
and separated from it by a colon. E.g. "-codec:a:1 ac3" option contains
"a:1" stream specifer, which matches the second audio stream. Therefore
it would select the ac3 codec for the second audio stream.
A stream specifier can match several stream, the option is then applied
to all of them. E.g. the stream specifier in "-b:a 128k" matches all
audio streams.
An empty stream specifier matches all streams, for example "-codec
copy" or "-codec: copy" would copy all the streams without reencoding.
Possible forms of stream specifiers are:
stream_index
Matches the stream with this index. E.g. "-threads:1 4" would set
the thread count for the second stream to 4.
stream_type[:stream_index]
stream_type is one of: 'v' for video, 'a' for audio, 's' for
subtitle, 'd' for data and 't' for attachments. If stream_index is
given, then matches stream number stream_index of this type.
Otherwise matches all streams of this type.
p:program_id[:stream_index]
If stream_index is given, then matches stream number stream_index
in program with id program_id. Otherwise matches all streams in
this program.
i:stream_id
Match the stream by stream id (e.g. PID in MPEG-TS container).
m:key[:value]
Matches streams with the metadata tag key having the specified
value. If value is not given, matches streams that contain the
given tag with any value.
Note that in avconv, matching by metadata will only work properly
for input files.
Generic options
These options are shared amongst the av* tools.
-L Show license.
-h, -?, -help, --help [arg]
Show help. An optional parameter may be specified to print help
about a specific item.
Possible values of arg are:
decoder=decoder_name
Print detailed information about the decoder named
decoder_name. Use the -decoders option to get a list of all
decoders.
encoder=encoder_name
Print detailed information about the encoder named
encoder_name. Use the -encoders option to get a list of all
encoders.
demuxer=demuxer_name
Print detailed information about the demuxer named
demuxer_name. Use the -formats option to get a list of all
demuxers and muxers.
muxer=muxer_name
Print detailed information about the muxer named muxer_name.
Use the -formats option to get a list of all muxers and
demuxers.
filter=filter_name
Print detailed information about the filter name filter_name.
Use the -filters option to get a list of all filters.
-version
Show version.
-formats
Show available formats.
The fields preceding the format names have the following meanings:
D Decoding available
E Encoding available
-codecs
Show all codecs known to libavcodec.
Note that the term 'codec' is used throughout this documentation as
a shortcut for what is more correctly called a media bitstream
format.
-decoders
Show available decoders.
-encoders
Show all available encoders.
-bsfs
Show available bitstream filters.
-protocols
Show available protocols.
-filters
Show available libavfilter filters.
-pix_fmts
Show available pixel formats.
-sample_fmts
Show available sample formats.
-loglevel loglevel | -v loglevel
Set the logging level used by the library. loglevel is a number or
a string containing one of the following values:
quiet
panic
fatal
error
warning
info
verbose
debug
By default the program logs to stderr, if coloring is supported by
the terminal, colors are used to mark errors and warnings. Log
coloring can be disabled setting the environment variable
AV_LOG_FORCE_NOCOLOR or NO_COLOR, or can be forced setting the
environment variable AV_LOG_FORCE_COLOR. The use of the
environment variable NO_COLOR is deprecated and will be dropped in
a following Libav version.
-cpuflags mask (global)
Set a mask that's applied to autodetected CPU flags. This option is
intended for testing. Do not use it unless you know what you're
doing.
AVOptions
These options are provided directly by the libavformat, libavdevice and
libavcodec libraries. To see the list of available AVOptions, use the
-help option. They are separated into two categories:
generic
These options can be set for any container, codec or device.
Generic options are listed under AVFormatContext options for
containers/devices and under AVCodecContext options for codecs.
private
These options are specific to the given container, device or codec.
Private options are listed under their corresponding
containers/devices/codecs.
For example to write an ID3v2.3 header instead of a default ID3v2.4 to
an MP3 file, use the id3v2_version private option of the MP3 muxer:
avconv -i input.flac -id3v2_version 3 out.mp3
All codec AVOptions are obviously per-stream, so the chapter on stream
specifiers applies to them
Note -nooption syntax cannot be used for boolean AVOptions, use -option
0/-option 1.
Note2 old undocumented way of specifying per-stream AVOptions by
prepending v/a/s to the options name is now obsolete and will be
removed soon.
Codec AVOptions
-b[:stream_specifier] integer (output,audio,video)
set bitrate (in bits/s)
-bt[:stream_specifier] integer (output,video)
Set video bitrate tolerance (in bits/s). In 1-pass mode, bitrate
tolerance specifies how far ratecontrol is willing to deviate from
the target average bitrate value. This is not related to
minimum/maximum bitrate. Lowering tolerance too much has an adverse
effect on quality.
-flags[:stream_specifier] flags (input/output,audio,video)
Possible values:
unaligned
allow decoders to produce unaligned output
mv4 use four motion vectors per macroblock (MPEG-4)
qpel
use 1/4-pel motion compensation
loop
use loop filter
qscale
use fixed qscale
gmc use gmc
mv0 always try a mb with mv=<0,0>
input_preserved
pass1
use internal 2-pass ratecontrol in first pass mode
pass2
use internal 2-pass ratecontrol in second pass mode
gray
only decode/encode grayscale
emu_edge
do not draw edges
psnr
error[?] variables will be set during encoding
truncated
naq normalize adaptive quantization
ildct
use interlaced DCT
low_delay
force low delay
global_header
place global headers in extradata instead of every keyframe
bitexact
use only bitexact functions (except (I)DCT)
aic H.263 advanced intra coding / MPEG-4 AC prediction
ilme
interlaced motion estimation
cgop
closed GOP
output_corrupt
Output even potentially corrupted frames
-me_method[:stream_specifier] integer (output,video)
set motion estimation method
Possible values:
zero
zero motion estimation (fastest)
full
full motion estimation (slowest)
epzs
EPZS motion estimation (default)
esa esa motion estimation (alias for full)
tesa
tesa motion estimation
dia diamond motion estimation (alias for EPZS)
log log motion estimation
phods
phods motion estimation
x1 X1 motion estimation
hex hex motion estimation
umh umh motion estimation
-g[:stream_specifier] integer (output,video)
set the group of picture (GOP) size
-ar[:stream_specifier] integer (input/output,audio)
set audio sampling rate (in Hz)
-ac[:stream_specifier] integer (input/output,audio)
set number of audio channels
-cutoff[:stream_specifier] integer (output,audio)
set cutoff bandwidth
-frame_size[:stream_specifier] integer (output,audio)
-qcomp[:stream_specifier] float (output,video)
video quantizer scale compression (VBR). Constant of ratecontrol
equation. Recommended range for default rc_eq: 0.0-1.0
-qblur[:stream_specifier] float (output,video)
video quantizer scale blur (VBR)
-qmin[:stream_specifier] integer (output,video)
minimum video quantizer scale (VBR)
-qmax[:stream_specifier] integer (output,video)
maximum video quantizer scale (VBR)
-qdiff[:stream_specifier] integer (output,video)
maximum difference between the quantizer scales (VBR)
-bf[:stream_specifier] integer (output,video)
use 'frames' B frames
-b_qfactor[:stream_specifier] float (output,video)
QP factor between P- and B-frames
-rc_strategy[:stream_specifier] integer (output,video)
ratecontrol method
-b_strategy[:stream_specifier] integer (output,video)
strategy to choose between I/P/B-frames
-ps[:stream_specifier] integer (output,video)
RTP payload size in bytes
-bug[:stream_specifier] flags (input,video)
work around not autodetected encoder bugs
Possible values:
autodetect
old_msmpeg4
some old lavc-generated MSMPEG4v3 files (no autodetection)
xvid_ilace
Xvid interlacing bug (autodetected if FOURCC == XVIX)
ump4
(autodetected if FOURCC == UMP4)
no_padding
padding bug (autodetected)
amv
ac_vlc
illegal VLC bug (autodetected per FOURCC)
qpel_chroma
std_qpel
old standard qpel (autodetected per FOURCC/version)
qpel_chroma2
direct_blocksize
direct-qpel-blocksize bug (autodetected per FOURCC/version)
edge
edge padding bug (autodetected per FOURCC/version)
hpel_chroma
dc_clip
ms work around various bugs in Microsoft's broken decoders
trunc
truncated frames
-strict[:stream_specifier] integer (input/output,audio,video)
how strictly to follow the standards
Possible values:
very
strictly conform to a older more strict version of the spec or
reference software
strict
strictly conform to all the things in the spec no matter what
the consequences
normal
unofficial
allow unofficial extensions
experimental
allow non-standardized experimental things
-b_qoffset[:stream_specifier] float (output,video)
QP offset between P- and B-frames
-err_detect[:stream_specifier] flags (input,audio,video)
set error detection flags
Possible values:
crccheck
verify embedded CRCs
bitstream
detect bitstream specification deviations
buffer
detect improper bitstream length
explode
abort decoding on minor error detection
-mpeg_quant[:stream_specifier] integer (output,video)
use MPEG quantizers instead of H.263
-qsquish[:stream_specifier] float (output,video)
how to keep quantizer between qmin and qmax (0 = clip, 1 = use
differentiable function)
-rc_qmod_amp[:stream_specifier] float (output,video)
experimental quantizer modulation
-rc_qmod_freq[:stream_specifier] integer (output,video)
experimental quantizer modulation
-rc_eq[:stream_specifier] string (output,video)
Set rate control equation. When computing the expression, besides
the standard functions defined in the section 'Expression
Evaluation', the following functions are available: bits2qp(bits),
qp2bits(qp). Also the following constants are available: iTex pTex
tex mv fCode iCount mcVar var isI isP isB avgQP qComp avgIITex
avgPITex avgPPTex avgBPTex avgTex.
-maxrate[:stream_specifier] integer (output,audio,video)
Set maximum bitrate tolerance (in bits/s). Requires bufsize to be
set.
-minrate[:stream_specifier] integer (output,audio,video)
Set minimum bitrate tolerance (in bits/s). Most useful in setting
up a CBR encode. It is of little use otherwise.
-bufsize[:stream_specifier] integer (output,audio,video)
set ratecontrol buffer size (in bits)
-rc_buf_aggressivity[:stream_specifier] float (output,video)
currently useless
-i_qfactor[:stream_specifier] float (output,video)
QP factor between P- and I-frames
-i_qoffset[:stream_specifier] float (output,video)
QP offset between P- and I-frames
-rc_init_cplx[:stream_specifier] float (output,video)
initial complexity for 1-pass encoding
-dct[:stream_specifier] integer (output,video)
DCT algorithm
Possible values:
auto
autoselect a good one (default)
fastint
fast integer
int accurate integer
mmx
altivec
faan
floating point AAN DCT
-lumi_mask[:stream_specifier] float (output,video)
compresses bright areas stronger than medium ones
-tcplx_mask[:stream_specifier] float (output,video)
temporal complexity masking
-scplx_mask[:stream_specifier] float (output,video)
spatial complexity masking
-p_mask[:stream_specifier] float (output,video)
inter masking
-dark_mask[:stream_specifier] float (output,video)
compresses dark areas stronger than medium ones
-idct[:stream_specifier] integer (input/output,video)
select IDCT implementation
Possible values:
auto
int
simple
simplemmx
arm
altivec
sh4
simplearm
simplearmv5te
simplearmv6
simpleneon
simplealpha
ipp
xvid
xvidmmx
faani
floating point AAN IDCT
-ec[:stream_specifier] flags (input,video)
set error concealment strategy
Possible values:
guess_mvs
iterative motion vector (MV) search (slow)
deblock
use strong deblock filter for damaged MBs
-pred[:stream_specifier] integer (output,video)
prediction method
Possible values:
left
plane
median
-aspect[:stream_specifier] rational number (output,video)
sample aspect ratio
-debug[:stream_specifier] flags (input/output,audio,video,subtitles)
print specific debug info
Possible values:
pict
picture info
rc rate control
bitstream
mb_type
macroblock (MB) type
qp per-block quantization parameter (QP)
mv motion vector
dct_coeff
skip
startcode
pts
er error recognition
mmco
memory management control operations (H.264)
bugs
vis_qp
visualize quantization parameter (QP), lower QP are tinted
greener
vis_mb_type
visualize block types
buffers
picture buffer allocations
thread_ops
threading operations
-vismv[:stream_specifier] integer (input,video)
visualize motion vectors (MVs)
Possible values:
pf forward predicted MVs of P-frames
bf forward predicted MVs of B-frames
bb backward predicted MVs of B-frames
-cmp[:stream_specifier] integer (output,video)
full-pel ME compare function
Possible values:
sad sum of absolute differences, fast (default)
sse sum of squared errors
satd
sum of absolute Hadamard transformed differences
dct sum of absolute DCT transformed differences
psnr
sum of squared quantization errors (avoid, low quality)
bit number of bits needed for the block
rd rate distortion optimal, slow
zero
0
vsad
sum of absolute vertical differences
vsse
sum of squared vertical differences
nsse
noise preserving sum of squared differences
dctmax
chroma
-subcmp[:stream_specifier] integer (output,video)
sub-pel ME compare function
Possible values:
sad sum of absolute differences, fast (default)
sse sum of squared errors
satd
sum of absolute Hadamard transformed differences
dct sum of absolute DCT transformed differences
psnr
sum of squared quantization errors (avoid, low quality)
bit number of bits needed for the block
rd rate distortion optimal, slow
zero
0
vsad
sum of absolute vertical differences
vsse
sum of squared vertical differences
nsse
noise preserving sum of squared differences
dctmax
chroma
-mbcmp[:stream_specifier] integer (output,video)
macroblock compare function
Possible values:
sad sum of absolute differences, fast (default)
sse sum of squared errors
satd
sum of absolute Hadamard transformed differences
dct sum of absolute DCT transformed differences
psnr
sum of squared quantization errors (avoid, low quality)
bit number of bits needed for the block
rd rate distortion optimal, slow
zero
0
vsad
sum of absolute vertical differences
vsse
sum of squared vertical differences
nsse
noise preserving sum of squared differences
dctmax
chroma
-ildctcmp[:stream_specifier] integer (output,video)
interlaced DCT compare function
Possible values:
sad sum of absolute differences, fast (default)
sse sum of squared errors
satd
sum of absolute Hadamard transformed differences
dct sum of absolute DCT transformed differences
psnr
sum of squared quantization errors (avoid, low quality)
bit number of bits needed for the block
rd rate distortion optimal, slow
zero
0
vsad
sum of absolute vertical differences
vsse
sum of squared vertical differences
nsse
noise preserving sum of squared differences
dctmax
chroma
-dia_size[:stream_specifier] integer (output,video)
diamond type & size for motion estimation
-last_pred[:stream_specifier] integer (output,video)
amount of motion predictors from the previous frame
-preme[:stream_specifier] integer (output,video)
pre motion estimation
-precmp[:stream_specifier] integer (output,video)
pre motion estimation compare function
Possible values:
sad sum of absolute differences, fast (default)
sse sum of squared errors
satd
sum of absolute Hadamard transformed differences
dct sum of absolute DCT transformed differences
psnr
sum of squared quantization errors (avoid, low quality)
bit number of bits needed for the block
rd rate distortion optimal, slow
zero
0
vsad
sum of absolute vertical differences
vsse
sum of squared vertical differences
nsse
noise preserving sum of squared differences
dctmax
chroma
-pre_dia_size[:stream_specifier] integer (output,video)
diamond type & size for motion estimation pre-pass
-subq[:stream_specifier] integer (output,video)
sub-pel motion estimation quality
-me_range[:stream_specifier] integer (output,video)
limit motion vectors range (1023 for DivX player)
-ibias[:stream_specifier] integer (output,video)
intra quant bias
-pbias[:stream_specifier] integer (output,video)
inter quant bias
-global_quality[:stream_specifier] integer (output,audio,video)
-coder[:stream_specifier] integer (output,video)
Possible values:
vlc variable length coder / Huffman coder
ac arithmetic coder
raw raw (no encoding)
rle run-length coder
deflate
deflate-based coder
-context[:stream_specifier] integer (output,video)
context model
-mbd[:stream_specifier] integer (output,video)
macroblock decision algorithm (high quality mode)
Possible values:
simple
use mbcmp (default)
bits
use fewest bits
rd use best rate distortion
-sc_threshold[:stream_specifier] integer (output,video)
scene change threshold
-lmin[:stream_specifier] integer (output,video)
minimum Lagrange factor (VBR)
-lmax[:stream_specifier] integer (output,video)
maximum Lagrange factor (VBR)
-nr[:stream_specifier] integer (output,video)
noise reduction
-rc_init_occupancy[:stream_specifier] integer (output,video)
number of bits which should be loaded into the rc buffer before
decoding starts
-flags2[:stream_specifier] flags (input/output,audio,video)
Possible values:
fast
allow non-spec-compliant speedup tricks
noout
skip bitstream encoding
ignorecrop
ignore cropping information from sps
local_header
place global headers at every keyframe instead of in extradata
-error[:stream_specifier] integer (output,video)
-threads[:stream_specifier] integer (input/output,video)
Possible values:
auto
autodetect a suitable number of threads to use
-me_threshold[:stream_specifier] integer (output,video)
motion estimation threshold
-mb_threshold[:stream_specifier] integer (output,video)
macroblock threshold
-dc[:stream_specifier] integer (output,video)
intra_dc_precision
-nssew[:stream_specifier] integer (output,video)
nsse weight
-skip_top[:stream_specifier] integer (input,video)
number of macroblock rows at the top which are skipped
-skip_bottom[:stream_specifier] integer (input,video)
number of macroblock rows at the bottom which are skipped
-profile[:stream_specifier] integer (output,audio,video)
Possible values:
unknown
aac_main
aac_low
aac_ssr
aac_ltp
aac_he
aac_he_v2
aac_ld
aac_eld
mpeg2_aac_low
mpeg2_aac_he
dts
dts_es
dts_96_24
dts_hd_hra
dts_hd_ma
-level[:stream_specifier] integer (output,audio,video)
Possible values:
unknown
-skip_threshold[:stream_specifier] integer (output,video)
frame skip threshold
-skip_factor[:stream_specifier] integer (output,video)
frame skip factor
-skip_exp[:stream_specifier] integer (output,video)
frame skip exponent
-skipcmp[:stream_specifier] integer (output,video)
frame skip compare function
Possible values:
sad sum of absolute differences, fast (default)
sse sum of squared errors
satd
sum of absolute Hadamard transformed differences
dct sum of absolute DCT transformed differences
psnr
sum of squared quantization errors (avoid, low quality)
bit number of bits needed for the block
rd rate distortion optimal, slow
zero
0
vsad
sum of absolute vertical differences
vsse
sum of squared vertical differences
nsse
noise preserving sum of squared differences
dctmax
chroma
-border_mask[:stream_specifier] float (output,video)
increase the quantizer for macroblocks close to borders
-mblmin[:stream_specifier] integer (output,video)
minimum macroblock Lagrange factor (VBR)
-mblmax[:stream_specifier] integer (output,video)
maximum macroblock Lagrange factor (VBR)
-mepc[:stream_specifier] integer (output,video)
motion estimation bitrate penalty compensation (1.0 = 256)
-skip_loop_filter[:stream_specifier] integer (input,video)
Possible values:
none
default
noref
bidir
nokey
all
-skip_idct[:stream_specifier] integer (input,video)
Possible values:
none
default
noref
bidir
nokey
all
-skip_frame[:stream_specifier] integer (input,video)
Possible values:
none
default
noref
bidir
nokey
all
-bidir_refine[:stream_specifier] integer (output,video)
refine the two motion vectors used in bidirectional macroblocks
-brd_scale[:stream_specifier] integer (output,video)
downscale frames for dynamic B-frame decision
-keyint_min[:stream_specifier] integer (output,video)
minimum interval between IDR-frames (x264)
-refs[:stream_specifier] integer (output,video)
reference frames to consider for motion compensation
-chromaoffset[:stream_specifier] integer (output,video)
chroma QP offset from luma
-trellis[:stream_specifier] integer (output,audio,video)
rate-distortion optimal quantization
-sc_factor[:stream_specifier] integer (output,video)
multiplied by qscale for each frame and added to scene_change_score
-mv0_threshold[:stream_specifier] integer (output,video)
-b_sensitivity[:stream_specifier] integer (output,video)
adjust sensitivity of b_frame_strategy 1
-compression_level[:stream_specifier] integer (output,audio,video)
-min_prediction_order[:stream_specifier] integer (output,audio)
-max_prediction_order[:stream_specifier] integer (output,audio)
-timecode_frame_start[:stream_specifier] integer (output,video)
GOP timecode frame start number, in non-drop-frame format
-request_channels[:stream_specifier] integer (input,audio)
set desired number of audio channels
-channel_layout[:stream_specifier] integer (input/output,audio)
Possible values:
-request_channel_layout[:stream_specifier] integer (input,audio)
Possible values:
-rc_max_vbv_use[:stream_specifier] float (output,video)
-rc_min_vbv_use[:stream_specifier] float (output,video)
-ticks_per_frame[:stream_specifier] integer (input/output,audio,video)
-color_primaries[:stream_specifier] integer (input/output,video)
color primaries
Possible values:
bt709
BT.709
unspecified
Unspecified
bt470m
BT.470 M
bt470bg
BT.470 BG
smpte170m
SMPTE 170 M
smpte240m
SMPTE 240 M
film
Film
bt2020
BT.2020
-color_trc[:stream_specifier] integer (input/output,video)
color transfert characteristic
Possible values:
bt709
BT.709
unspecified
Unspecified
gamma22
Gamma 2.2
gamma28
Gamma 2.8
smpte170m
SMPTE 170 M
smpte240m
SMPTE 240 M
linear
Linear
log SMPTE 240 M
log_sqrt
SMPTE 240 M
iec61966_2_4
SMPTE 240 M
bt1361
BT.1361
iec61966_2_1
SMPTE 240 M
bt2020_10bit
BT.2020 - 10 bit
bt2020_12bit
BT.2020 - 12 bit
-colorspace[:stream_specifier] integer (input/output,video)
colorspace
Possible values:
rgb RGB
bt709
BT.709
unspecified
Unspecified
fcc FourCC
bt470bg
BT.470 BG
smpte170m
SMPTE 170 M
smpte240m
SMPTE 240 M
ycocg
YCOCG
bt2020_ncl
BT.2020 NCL
bt2020_cl
BT.2020 CL
-color_range[:stream_specifier] integer (input/output,video)
color range
Possible values:
unspecified
Unspecified
mpeg
MPEG (219*2^(n-8))
jpeg
JPEG (2^n-1)
-chroma_sample_location[:stream_specifier] integer (input/output,video)
-slices[:stream_specifier] integer (output,video)
number of slices, used in parallelized encoding
-thread_type[:stream_specifier] flags (input/output,video)
select multithreading type
Possible values:
slice
frame
-audio_service_type[:stream_specifier] integer (output,audio)
audio service type
Possible values:
ma Main Audio Service
ef Effects
vi Visually Impaired
hi Hearing Impaired
di Dialogue
co Commentary
em Emergency
vo Voice Over
ka Karaoke
-request_sample_fmt[:stream_specifier] integer (input,audio)
Possible values:
u8 8-bit unsigned integer
s16 16-bit signed integer
s32 32-bit signed integer
flt 32-bit float
dbl 64-bit double
u8p 8-bit unsigned integer planar
s16p
16-bit signed integer planar
s32p
32-bit signed integer planar
fltp
32-bit float planar
dblp
64-bit double planar
-refcounted_frames[:stream_specifier] integer (input,audio,video)
-side_data_only_packets[:stream_specifier] integer (output,audio,video)
Format AVOptions
-probesize integer (input)
set probing size
-packetsize integer (output)
set packet size
-fflags flags (input/output)
Possible values:
flush_packets
reduce the latency by flushing out packets immediately
ignidx
ignore index
genpts
generate pts
nofillin
do not fill in missing values that can be exactly calculated
noparse
disable AVParsers, this needs nofillin too
igndts
ignore dts
discardcorrupt
discard corrupted frames
nobuffer
reduce the latency introduced by optional buffering
bitexact
do not write random/volatile data
-analyzeduration integer (input)
how many microseconds are analyzed to estimate duration
-cryptokey hexadecimal string (input)
decryption key
-indexmem integer (input)
max memory used for timestamp index (per stream)
-rtbufsize integer (input)
max memory used for buffering real-time frames
-fdebug flags (input/output)
print specific debug info
Possible values:
ts
-max_delay integer (input/output)
maximum muxing or demuxing delay in microseconds
-fpsprobesize integer (input)
number of frames used to probe fps
-f_err_detect flags (input)
set error detection flags (deprecated; use err_detect, save via
avconv)
Possible values:
crccheck
verify embedded CRCs
bitstream
detect bitstream specification deviations
buffer
detect improper bitstream length
explode
abort decoding on minor error detection
-err_detect flags (input)
set error detection flags
Possible values:
crccheck
verify embedded CRCs
bitstream
detect bitstream specification deviations
buffer
detect improper bitstream length
explode
abort decoding on minor error detection
-max_interleave_delta integer (output)
maximum buffering duration for interleaving
-f_strict integer (input/output)
how strictly to follow the standards (deprecated; use strict, save
via avconv)
Possible values:
strict
strictly conform to all the things in the spec no matter what
the consequences
normal
experimental
allow non-standardized experimental variants
-strict integer (input/output)
how strictly to follow the standards
Possible values:
strict
strictly conform to all the things in the spec no matter what
the consequences
normal
experimental
allow non-standardized experimental variants
Main options
-f fmt (input/output)
Force input or output file format. The format is normally
autodetected for input files and guessed from file extension for
output files, so this option is not needed in most cases.
-i filename (input)
input file name
-y (global)
Overwrite output files without asking.
-n (global)
Immediately exit when output files already exist.
-c[:stream_specifier] codec (input/output,per-stream)
-codec[:stream_specifier] codec (input/output,per-stream)
Select an encoder (when used before an output file) or a decoder
(when used before an input file) for one or more streams. codec is
the name of a decoder/encoder or a special value "copy" (output
only) to indicate that the stream is not to be reencoded.
For example
avconv -i INPUT -map 0 -c:v libx264 -c:a copy OUTPUT
encodes all video streams with libx264 and copies all audio
streams.
For each stream, the last matching "c" option is applied, so
avconv -i INPUT -map 0 -c copy -c:v:1 libx264 -c:a:137 libvorbis OUTPUT
will copy all the streams except the second video, which will be
encoded with libx264, and the 138th audio, which will be encoded
with libvorbis.
-t duration (output)
Stop writing the output after its duration reaches duration.
duration may be a number in seconds, or in "hh:mm:ss[.xxx]" form.
-fs limit_size (output)
Set the file size limit.
-ss position (input/output)
When used as an input option (before "-i"), seeks in this input
file to position. Note the in most formats it is not possible to
seek exactly, so avconv will seek to the closest seek point before
position. When transcoding and -accurate_seek is enabled (the
default), this extra segment between the seek point and position
will be decoded and discarded. When doing stream copy or when
-noaccurate_seek is used, it will be preserved.
When used as an output option (before an output filename), decodes
but discards input until the timestamps reach position.
position may be either in seconds or in "hh:mm:ss[.xxx]" form.
-itsoffset offset (input)
Set the input time offset in seconds. "[-]hh:mm:ss[.xxx]" syntax
is also supported. The offset is added to the timestamps of the
input files. Specifying a positive offset means that the
corresponding streams are delayed by offset seconds.
-metadata[:metadata_specifier] key=value (output,per-metadata)
Set a metadata key/value pair.
An optional metadata_specifier may be given to set metadata on
streams or chapters. See "-map_metadata" documentation for details.
This option overrides metadata set with "-map_metadata". It is also
possible to delete metadata by using an empty value.
For example, for setting the title in the output file:
avconv -i in.avi -metadata title="my title" out.flv
To set the language of the first audio stream:
avconv -i INPUT -metadata:s:a:0 language=eng OUTPUT
-target type (output)
Specify target file type ("vcd", "svcd", "dvd", "dv", "dv50"). type
may be prefixed with "pal-", "ntsc-" or "film-" to use the
corresponding standard. All the format options (bitrate, codecs,
buffer sizes) are then set automatically. You can just type:
avconv -i myfile.avi -target vcd /tmp/vcd.mpg
Nevertheless you can specify additional options as long as you know
they do not conflict with the standard, as in:
avconv -i myfile.avi -target vcd -bf 2 /tmp/vcd.mpg
-dframes number (output)
Set the number of data frames to record. This is an alias for
"-frames:d".
-frames[:stream_specifier] framecount (output,per-stream)
Stop writing to the stream after framecount frames.
-q[:stream_specifier] q (output,per-stream)
-qscale[:stream_specifier] q (output,per-stream)
Use fixed quality scale (VBR). The meaning of q is codec-dependent.
-filter[:stream_specifier] filter_graph (output,per-stream)
filter_graph is a description of the filter graph to apply to the
stream. Use "-filters" to show all the available filters (including
also sources and sinks).
See also the -filter_complex option if you want to create filter
graphs with multiple inputs and/or outputs.
-filter_script[:stream_specifier] filename (output,per-stream)
This option is similar to -filter, the only difference is that its
argument is the name of the file from which a filtergraph
description is to be read.
-pre[:stream_specifier] preset_name (output,per-stream)
Specify the preset for matching stream(s).
-stats (global)
Print encoding progress/statistics. On by default.
-attach filename (output)
Add an attachment to the output file. This is supported by a few
formats like Matroska for e.g. fonts used in rendering subtitles.
Attachments are implemented as a specific type of stream, so this
option will add a new stream to the file. It is then possible to
use per-stream options on this stream in the usual way. Attachment
streams created with this option will be created after all the
other streams (i.e. those created with "-map" or automatic
mappings).
Note that for Matroska you also have to set the mimetype metadata
tag:
avconv -i INPUT -attach DejaVuSans.ttf -metadata:s:2 mimetype=application/x-truetype-font out.mkv
(assuming that the attachment stream will be third in the output
file).
-dump_attachment[:stream_specifier] filename (input,per-stream)
Extract the matching attachment stream into a file named filename.
If filename is empty, then the value of the "filename" metadata tag
will be used.
E.g. to extract the first attachment to a file named 'out.ttf':
avconv -dump_attachment:t:0 out.ttf INPUT
To extract all attachments to files determined by the "filename"
tag:
avconv -dump_attachment:t "" INPUT
Technical note -- attachments are implemented as codec extradata,
so this option can actually be used to extract extradata from any
stream, not just attachments.
Video Options
-vframes number (output)
Set the number of video frames to record. This is an alias for
"-frames:v".
-r[:stream_specifier] fps (input/output,per-stream)
Set frame rate (Hz value, fraction or abbreviation).
As an input option, ignore any timestamps stored in the file and
instead generate timestamps assuming constant frame rate fps.
As an output option, duplicate or drop input frames to achieve
constant output frame rate fps (note that this actually causes the
"fps" filter to be inserted to the end of the corresponding
filtergraph).
-s[:stream_specifier] size (input/output,per-stream)
Set frame size.
As an input option, this is a shortcut for the video_size private
option, recognized by some demuxers for which the frame size is
either not stored in the file or is configurable -- e.g. raw video
or video grabbers.
As an output option, this inserts the "scale" video filter to the
end of the corresponding filtergraph. Please use the "scale" filter
directly to insert it at the beginning or some other place.
The format is wxh (default - same as source). The following
abbreviations are recognized:
sqcif
128x96
qcif
176x144
cif 352x288
4cif
704x576
16cif
1408x1152
qqvga
160x120
qvga
320x240
vga 640x480
svga
800x600
xga 1024x768
uxga
1600x1200
qxga
2048x1536
sxga
1280x1024
qsxga
2560x2048
hsxga
5120x4096
wvga
852x480
wxga
1366x768
wsxga
1600x1024
wuxga
1920x1200
woxga
2560x1600
wqsxga
3200x2048
wquxga
3840x2400
whsxga
6400x4096
whuxga
7680x4800
cga 320x200
ega 640x350
hd480
852x480
hd720
1280x720
hd1080
1920x1080
-aspect[:stream_specifier] aspect (output,per-stream)
Set the video display aspect ratio specified by aspect.
aspect can be a floating point number string, or a string of the
form num:den, where num and den are the numerator and denominator
of the aspect ratio. For example "4:3", "16:9", "1.3333", and
"1.7777" are valid argument values.
-vn (output)
Disable video recording.
-vcodec codec (output)
Set the video codec. This is an alias for "-codec:v".
-pass[:stream_specifier] n (output,per-stream)
Select the pass number (1 or 2). It is used to do two-pass video
encoding. The statistics of the video are recorded in the first
pass into a log file (see also the option -passlogfile), and in the
second pass that log file is used to generate the video at the
exact requested bitrate. On pass 1, you may just deactivate audio
and set output to null, examples for Windows and Unix:
avconv -i foo.mov -c:v libxvid -pass 1 -an -f rawvideo -y NUL
avconv -i foo.mov -c:v libxvid -pass 1 -an -f rawvideo -y /dev/null
-passlogfile[:stream_specifier] prefix (output,per-stream)
Set two-pass log file name prefix to prefix, the default file name
prefix is ``av2pass''. The complete file name will be PREFIX-N.log,
where N is a number specific to the output stream.
-vf filter_graph (output)
filter_graph is a description of the filter graph to apply to the
input video. Use the option "-filters" to show all the available
filters (including also sources and sinks). This is an alias for
"-filter:v".
Advanced Video Options
-pix_fmt[:stream_specifier] format (input/output,per-stream)
Set pixel format. Use "-pix_fmts" to show all the supported pixel
formats.
-sws_flags flags (input/output)
Set SwScaler flags.
-vdt n
Discard threshold.
-rc_override[:stream_specifier] override (output,per-stream)
rate control override for specific intervals
-vstats
Dump video coding statistics to vstats_HHMMSS.log.
-vstats_file file
Dump video coding statistics to file.
-top[:stream_specifier] n (output,per-stream)
top=1/bottom=0/auto=-1 field first
-dc precision
Intra_dc_precision.
-vtag fourcc/tag (output)
Force video tag/fourcc. This is an alias for "-tag:v".
-qphist (global)
Show QP histogram.
-force_key_frames[:stream_specifier] time[,time...] (output,per-stream)
Force key frames at the specified timestamps, more precisely at the
first frames after each specified time. This option can be useful
to ensure that a seek point is present at a chapter mark or any
other designated place in the output file. The timestamps must be
specified in ascending order.
-copyinkf[:stream_specifier] (output,per-stream)
When doing stream copy, copy also non-key frames found at the
beginning.
-hwaccel[:stream_specifier] hwaccel (input,per-stream)
Use hardware acceleration to decode the matching stream(s). The
allowed values of hwaccel are:
none
Do not use any hardware acceleration (the default).
auto
Automatically select the hardware acceleration method.
vda Use Apple VDA hardware acceleration.
vdpau
Use VDPAU (Video Decode and Presentation API for Unix) hardware
acceleration.
dxva2
Use DXVA2 (DirectX Video Acceleration) hardware acceleration.
This option has no effect if the selected hwaccel is not available
or not supported by the chosen decoder.
Note that most acceleration methods are intended for playback and
will not be faster than software decoding on modern CPUs.
Additionally, avconv will usually need to copy the decoded frames
from the GPU memory into the system memory, resulting in further
performance loss. This option is thus mainly useful for testing.
-hwaccel_device[:stream_specifier] hwaccel_device (input,per-stream)
Select a device to use for hardware acceleration.
This option only makes sense when the -hwaccel option is also
specified. Its exact meaning depends on the specific hardware
acceleration method chosen.
vdpau
For VDPAU, this option specifies the X11 display/screen to use.
If this option is not specified, the value of the DISPLAY
environment variable is used
dxva2
For DXVA2, this option should contain the number of the display
adapter to use. If this option is not specified, the default
adapter is used.
Audio Options
-aframes number (output)
Set the number of audio frames to record. This is an alias for
"-frames:a".
-ar[:stream_specifier] freq (input/output,per-stream)
Set the audio sampling frequency. For output streams it is set by
default to the frequency of the corresponding input stream. For
input streams this option only makes sense for audio grabbing
devices and raw demuxers and is mapped to the corresponding demuxer
options.
-aq q (output)
Set the audio quality (codec-specific, VBR). This is an alias for
-q:a.
-ac[:stream_specifier] channels (input/output,per-stream)
Set the number of audio channels. For output streams it is set by
default to the number of input audio channels. For input streams
this option only makes sense for audio grabbing devices and raw
demuxers and is mapped to the corresponding demuxer options.
-an (output)
Disable audio recording.
-acodec codec (input/output)
Set the audio codec. This is an alias for "-codec:a".
-sample_fmt[:stream_specifier] sample_fmt (output,per-stream)
Set the audio sample format. Use "-sample_fmts" to get a list of
supported sample formats.
-af filter_graph (output)
filter_graph is a description of the filter graph to apply to the
input audio. Use the option "-filters" to show all the available
filters (including also sources and sinks). This is an alias for
"-filter:a".
Advanced Audio options:
-atag fourcc/tag (output)
Force audio tag/fourcc. This is an alias for "-tag:a".
Subtitle options:
-scodec codec (input/output)
Set the subtitle codec. This is an alias for "-codec:s".
-sn (output)
Disable subtitle recording.
Advanced options
-map
[-]input_file_id[:stream_specifier][,sync_file_id[:stream_specifier]] |
[linklabel] (output)
Designate one or more input streams as a source for the output
file. Each input stream is identified by the input file index
input_file_id and the input stream index input_stream_id within the
input file. Both indices start at 0. If specified,
sync_file_id:stream_specifier sets which input stream is used as a
presentation sync reference.
The first "-map" option on the command line specifies the source
for output stream 0, the second "-map" option specifies the source
for output stream 1, etc.
A "-" character before the stream identifier creates a "negative"
mapping. It disables matching streams from already created
mappings.
An alternative [linklabel] form will map outputs from complex
filter graphs (see the -filter_complex option) to the output file.
linklabel must correspond to a defined output link label in the
graph.
For example, to map ALL streams from the first input file to output
avconv -i INPUT -map 0 output
For example, if you have two audio streams in the first input file,
these streams are identified by "0:0" and "0:1". You can use "-map"
to select which streams to place in an output file. For example:
avconv -i INPUT -map 0:1 out.wav
will map the input stream in INPUT identified by "0:1" to the
(single) output stream in out.wav.
For example, to select the stream with index 2 from input file
a.mov (specified by the identifier "0:2"), and stream with index 6
from input b.mov (specified by the identifier "1:6"), and copy them
to the output file out.mov:
avconv -i a.mov -i b.mov -c copy -map 0:2 -map 1:6 out.mov
To select all video and the third audio stream from an input file:
avconv -i INPUT -map 0:v -map 0:a:2 OUTPUT
To map all the streams except the second audio, use negative
mappings
avconv -i INPUT -map 0 -map -0:a:1 OUTPUT
To pick the English audio stream:
avconv -i INPUT -map 0:m:language:eng OUTPUT
Note that using this option disables the default mappings for this
output file.
-map_metadata[:metadata_spec_out] infile[:metadata_spec_in]
(output,per-metadata)
Set metadata information of the next output file from infile. Note
that those are file indices (zero-based), not filenames. Optional
metadata_spec_in/out parameters specify, which metadata to copy. A
metadata specifier can have the following forms:
g global metadata, i.e. metadata that applies to the whole file
s[:stream_spec]
per-stream metadata. stream_spec is a stream specifier as
described in the Stream specifiers chapter. In an input
metadata specifier, the first matching stream is copied from.
In an output metadata specifier, all matching streams are
copied to.
c:chapter_index
per-chapter metadata. chapter_index is the zero-based chapter
index.
p:program_index
per-program metadata. program_index is the zero-based program
index.
If metadata specifier is omitted, it defaults to global.
By default, global metadata is copied from the first input file,
per-stream and per-chapter metadata is copied along with
streams/chapters. These default mappings are disabled by creating
any mapping of the relevant type. A negative file index can be used
to create a dummy mapping that just disables automatic copying.
For example to copy metadata from the first stream of the input
file to global metadata of the output file:
avconv -i in.ogg -map_metadata 0:s:0 out.mp3
To do the reverse, i.e. copy global metadata to all audio streams:
avconv -i in.mkv -map_metadata:s:a 0:g out.mkv
Note that simple 0 would work as well in this example, since global
metadata is assumed by default.
-map_chapters input_file_index (output)
Copy chapters from input file with index input_file_index to the
next output file. If no chapter mapping is specified, then chapters
are copied from the first input file with at least one chapter. Use
a negative file index to disable any chapter copying.
-debug
Print specific debug info.
-benchmark (global)
Show benchmarking information at the end of an encode. Shows CPU
time used and maximum memory consumption. Maximum memory
consumption is not supported on all systems, it will usually
display as 0 if not supported.
-timelimit duration (global)
Exit after avconv has been running for duration seconds.
-dump (global)
Dump each input packet to stderr.
-hex (global)
When dumping packets, also dump the payload.
-re (input)
Read input at native frame rate. Mainly used to simulate a grab
device or live input stream (e.g. when reading from a file). Should
not be used with actual grab devices or live input streams (where
it can cause packet loss).
-vsync parameter
Video sync method.
passthrough
Each frame is passed with its timestamp from the demuxer to the
muxer.
cfr Frames will be duplicated and dropped to achieve exactly the
requested constant framerate.
vfr Frames are passed through with their timestamp or dropped so as
to prevent 2 frames from having the same timestamp.
auto
Chooses between 1 and 2 depending on muxer capabilities. This
is the default method.
With -map you can select from which stream the timestamps should be
taken. You can leave either video or audio unchanged and sync the
remaining stream(s) to the unchanged one.
-async samples_per_second
Audio sync method. "Stretches/squeezes" the audio stream to match
the timestamps, the parameter is the maximum samples per second by
which the audio is changed. -async 1 is a special case where only
the start of the audio stream is corrected without any later
correction. This option has been deprecated. Use the "asyncts"
audio filter instead.
-copyts
Copy timestamps from input to output.
-copytb
Copy input stream time base from input to output when stream
copying.
-shortest (output)
Finish encoding when the shortest input stream ends.
-dts_delta_threshold
Timestamp discontinuity delta threshold.
-muxdelay seconds (input)
Set the maximum demux-decode delay.
-muxpreload seconds (input)
Set the initial demux-decode delay.
-streamid output-stream-index:new-value (output)
Assign a new stream-id value to an output stream. This option
should be specified prior to the output filename to which it
applies. For the situation where multiple output files exist, a
streamid may be reassigned to a different value.
For example, to set the stream 0 PID to 33 and the stream 1 PID to
36 for an output mpegts file:
avconv -i infile -streamid 0:33 -streamid 1:36 out.ts
-bsf[:stream_specifier] bitstream_filters (output,per-stream)
Set bitstream filters for matching streams. bistream_filters is a
comma-separated list of bitstream filters. Use the "-bsfs" option
to get the list of bitstream filters.
avconv -i h264.mp4 -c:v copy -bsf:v h264_mp4toannexb -an out.h264
avconv -i file.mov -an -vn -bsf:s mov2textsub -c:s copy -f rawvideo sub.txt
-tag[:stream_specifier] codec_tag (input/output,per-stream)
Force a tag/fourcc for matching streams.
-filter_complex filtergraph (global)
Define a complex filter graph, i.e. one with arbitrary number of
inputs and/or outputs. For simple graphs -- those with one input
and one output of the same type -- see the -filter options.
filtergraph is a description of the filter graph, as described in
Filtergraph syntax.
Input link labels must refer to input streams using the
"[file_index:stream_specifier]" syntax (i.e. the same as -map
uses). If stream_specifier matches multiple streams, the first one
will be used. An unlabeled input will be connected to the first
unused input stream of the matching type.
Output link labels are referred to with -map. Unlabeled outputs are
added to the first output file.
Note that with this option it is possible to use only lavfi sources
without normal input files.
For example, to overlay an image over video
avconv -i video.mkv -i image.png -filter_complex '[0:v][1:v]overlay[out]' -map
'[out]' out.mkv
Here "[0:v]" refers to the first video stream in the first input
file, which is linked to the first (main) input of the overlay
filter. Similarly the first video stream in the second input is
linked to the second (overlay) input of overlay.
Assuming there is only one video stream in each input file, we can
omit input labels, so the above is equivalent to
avconv -i video.mkv -i image.png -filter_complex 'overlay[out]' -map
'[out]' out.mkv
Furthermore we can omit the output label and the single output from
the filter graph will be added to the output file automatically, so
we can simply write
avconv -i video.mkv -i image.png -filter_complex 'overlay' out.mkv
To generate 5 seconds of pure red video using lavfi "color" source:
avconv -filter_complex 'color=red' -t 5 out.mkv
-filter_complex_script filename (global)
This option is similar to -filter_complex, the only difference is
that its argument is the name of the file from which a complex
filtergraph description is to be read.
-accurate_seek (input)
This option enables or disables accurate seeking in input files
with the -ss option. It is enabled by default, so seeking is
accurate when transcoding. Use -noaccurate_seek to disable it,
which may be useful e.g. when copying some streams and transcoding
the others.
o For streaming at very low bitrate application, use a low frame rate
and a small GOP size. This is especially true for RealVideo where
the Linux player does not seem to be very fast, so it can miss
frames. An example is:
avconv -g 3 -r 3 -t 10 -b 50k -s qcif -f rv10 /tmp/b.rm
o The parameter 'q' which is displayed while encoding is the current
quantizer. The value 1 indicates that a very good quality could be
achieved. The value 31 indicates the worst quality. If q=31 appears
too often, it means that the encoder cannot compress enough to meet
your bitrate. You must either increase the bitrate, decrease the
frame rate or decrease the frame size.
o If your computer is not fast enough, you can speed up the
compression at the expense of the compression ratio. You can use
'-me zero' to speed up motion estimation, and '-g 0' to disable
motion estimation completely (you have only I-frames, which means
it is about as good as JPEG compression).
o To have very low audio bitrates, reduce the sampling frequency
(down to 22050 Hz for MPEG audio, 22050 or 11025 for AC-3).
o To have a constant quality (but a variable bitrate), use the option
'-qscale n' when 'n' is between 1 (excellent quality) and 31 (worst
quality).
Preset files
A preset file contains a sequence of option=value pairs, one for each
line, specifying a sequence of options which can be specified also on
the command line. Lines starting with the hash ('#') character are
ignored and are used to provide comments. Empty lines are also ignored.
Check the presets directory in the Libav source tree for examples.
Preset files are specified with the "pre" option, this option takes a
preset name as input. Avconv searches for a file named
preset_name.avpreset in the directories $AVCONV_DATADIR (if set), and
$HOME/.avconv, and in the data directory defined at configuration time
(usually $PREFIX/share/avconv) in that order. For example, if the
argument is "libx264-max", it will search for the file
libx264-max.avpreset.
Video and Audio grabbing
If you specify the input format and device then avconv can grab video
and audio directly.
avconv -f oss -i /dev/dsp -f video4linux2 -i /dev/video0 /tmp/out.mpg
Note that you must activate the right video source and channel before
launching avconv with any TV viewer such as
xawtv ("http://linux.bytesex.org/xawtv/") by Gerd Knorr. You also have
to set the audio recording levels correctly with a standard mixer.
X11 grabbing
Grab the X11 display with avconv via
avconv -f x11grab -s cif -r 25 -i :0.0 /tmp/out.mpg
0.0 is display.screen number of your X11 server, same as the DISPLAY
environment variable.
avconv -f x11grab -s cif -r 25 -i :0.0+10,20 /tmp/out.mpg
0.0 is display.screen number of your X11 server, same as the DISPLAY
environment variable. 10 is the x-offset and 20 the y-offset for the
grabbing.
Video and Audio file format conversion
Any supported file format and protocol can serve as input to avconv:
Examples:
o You can use YUV files as input:
avconv -i /tmp/test%d.Y /tmp/out.mpg
It will use the files:
/tmp/test0.Y, /tmp/test0.U, /tmp/test0.V,
/tmp/test1.Y, /tmp/test1.U, /tmp/test1.V, etc...
The Y files use twice the resolution of the U and V files. They are
raw files, without header. They can be generated by all decent
video decoders. You must specify the size of the image with the -s
option if avconv cannot guess it.
o You can input from a raw YUV420P file:
avconv -i /tmp/test.yuv /tmp/out.avi
test.yuv is a file containing raw YUV planar data. Each frame is
composed of the Y plane followed by the U and V planes at half
vertical and horizontal resolution.
o You can output to a raw YUV420P file:
avconv -i mydivx.avi hugefile.yuv
o You can set several input files and output files:
avconv -i /tmp/a.wav -s 640x480 -i /tmp/a.yuv /tmp/a.mpg
Converts the audio file a.wav and the raw YUV video file a.yuv to
MPEG file a.mpg.
o You can also do audio and video conversions at the same time:
avconv -i /tmp/a.wav -ar 22050 /tmp/a.mp2
Converts a.wav to MPEG audio at 22050 Hz sample rate.
o You can encode to several formats at the same time and define a
mapping from input stream to output streams:
avconv -i /tmp/a.wav -map 0:a -b 64k /tmp/a.mp2 -map 0:a -b 128k /tmp/b.mp2
Converts a.wav to a.mp2 at 64 kbits and to b.mp2 at 128 kbits.
'-map file:index' specifies which input stream is used for each
output stream, in the order of the definition of output streams.
o You can transcode decrypted VOBs:
avconv -i snatch_1.vob -f avi -c:v mpeg4 -b:v 800k -g 300 -bf 2 -c:a libmp3lame -b:a 128k snatch.avi
This is a typical DVD ripping example; the input is a VOB file, the
output an AVI file with MPEG-4 video and MP3 audio. Note that in
this command we use B-frames so the MPEG-4 stream is DivX5
compatible, and GOP size is 300 which means one intra frame every
10 seconds for 29.97fps input video. Furthermore, the audio stream
is MP3-encoded so you need to enable LAME support by passing
"--enable-libmp3lame" to configure. The mapping is particularly
useful for DVD transcoding to get the desired audio language.
NOTE: To see the supported input formats, use "avconv -formats".
o You can extract images from a video, or create a video from many
images:
For extracting images from a video:
avconv -i foo.avi -r 1 -s WxH -f image2 foo-%03d.jpeg
This will extract one video frame per second from the video and
will output them in files named foo-001.jpeg, foo-002.jpeg, etc.
Images will be rescaled to fit the new WxH values.
If you want to extract just a limited number of frames, you can use
the above command in combination with the -vframes or -t option, or
in combination with -ss to start extracting from a certain point in
time.
For creating a video from many images:
avconv -f image2 -i foo-%03d.jpeg -r 12 -s WxH foo.avi
The syntax "foo-%03d.jpeg" specifies to use a decimal number
composed of three digits padded with zeroes to express the sequence
number. It is the same syntax supported by the C printf function,
but only formats accepting a normal integer are suitable.
o You can put many streams of the same type in the output:
avconv -i test1.avi -i test2.avi -map 1:1 -map 1:0 -map 0:1 -map 0:0 -c copy -y test12.nut
The resulting output file test12.nut will contain the first four
streams from the input files in reverse order.
o To force CBR video output:
avconv -i myfile.avi -b 4000k -minrate 4000k -maxrate 4000k -bufsize 1835k out.m2v
o The four options lmin, lmax, mblmin and mblmax use 'lambda' units,
but you may use the QP2LAMBDA constant to easily convert from 'q'
units:
avconv -i src.ext -lmax 21*QP2LAMBDA dst.ext
When evaluating an arithmetic expression, Libav uses an internal
formula evaluator, implemented through the libavutil/eval.h interface.
An expression may contain unary, binary operators, constants, and
functions.
Two expressions expr1 and expr2 can be combined to form another
expression "expr1;expr2". expr1 and expr2 are evaluated in turn, and
the new expression evaluates to the value of expr2.
The following binary operators are available: "+", "-", "*", "/", "^".
The following unary operators are available: "+", "-".
The following functions are available:
sinh(x)
cosh(x)
tanh(x)
sin(x)
cos(x)
tan(x)
atan(x)
asin(x)
acos(x)
exp(x)
log(x)
abs(x)
squish(x)
gauss(x)
isinf(x)
Return 1.0 if x is +/-INFINITY, 0.0 otherwise.
isnan(x)
Return 1.0 if x is NAN, 0.0 otherwise.
mod(x, y)
max(x, y)
min(x, y)
eq(x, y)
gte(x, y)
gt(x, y)
lte(x, y)
lt(x, y)
st(var, expr)
Allow to store the value of the expression expr in an internal
variable. var specifies the number of the variable where to store
the value, and it is a value ranging from 0 to 9. The function
returns the value stored in the internal variable.
ld(var)
Allow to load the value of the internal variable with number var,
which was previously stored with st(var, expr). The function
returns the loaded value.
while(cond, expr)
Evaluate expression expr while the expression cond is non-zero, and
returns the value of the last expr evaluation, or NAN if cond was
always false.
ceil(expr)
Round the value of expression expr upwards to the nearest integer.
For example, "ceil(1.5)" is "2.0".
floor(expr)
Round the value of expression expr downwards to the nearest
integer. For example, "floor(-1.5)" is "-2.0".
trunc(expr)
Round the value of expression expr towards zero to the nearest
integer. For example, "trunc(-1.5)" is "-1.0".
sqrt(expr)
Compute the square root of expr. This is equivalent to "(expr)^.5".
not(expr)
Return 1.0 if expr is zero, 0.0 otherwise.
Note that:
"*" works like AND
"+" works like OR
thus
if A then B else C
is equivalent to
A*B + not(A)*C
In your C code, you can extend the list of unary and binary functions,
and define recognized constants, so that they are available for your
expressions.
The evaluator also recognizes the International System number
postfixes. If 'i' is appended after the postfix, powers of 2 are used
instead of powers of 10. The 'B' postfix multiplies the value for 8,
and can be appended after another postfix or used alone. This allows
using for example 'KB', 'MiB', 'G' and 'B' as postfix.
Follows the list of available International System postfixes, with
indication of the corresponding powers of 10 and of 2.
y -24 / -80
z -21 / -70
a -18 / -60
f -15 / -50
p -12 / -40
n -9 / -30
u -6 / -20
m -3 / -10
c -2
d -1
h 2
k 3 / 10
K 3 / 10
M 6 / 20
G 9 / 30
T 12 / 40
P 15 / 40
E 18 / 50
Z 21 / 60
Y 24 / 70
Decoders are configured elements in Libav which allow the decoding of
multimedia streams.
When you configure your Libav build, all the supported native decoders
are enabled by default. Decoders requiring an external library must be
enabled manually via the corresponding "--enable-lib" option. You can
list all available decoders using the configure option
"--list-decoders".
You can disable all the decoders with the configure option
"--disable-decoders" and selectively enable / disable single decoders
with the options "--enable-decoder=DECODER" /
"--disable-decoder=DECODER".
The option "-decoders" of the av* tools will display the list of
enabled decoders.
A description of some of the currently available audio decoders
follows.
ac3
AC-3 audio decoder.
This decoder implements part of ATSC A/52:2010 and ETSI TS 102 366, as
well as the undocumented RealAudio 3 (a.k.a. dnet).
AC-3 Decoder Options
-drc_scale value
Dynamic Range Scale Factor. The factor to apply to dynamic range
values from the AC-3 stream. This factor is applied exponentially.
There are 3 notable scale factor ranges:
drc_scale == 0
DRC disabled. Produces full range audio.
0 < drc_scale <= 1
DRC enabled. Applies a fraction of the stream DRC value.
Audio reproduction is between full range and full compression.
drc_scale > 1
DRC enabled. Applies drc_scale asymmetrically. Loud sounds are
fully compressed. Soft sounds are enhanced.
Encoders are configured elements in Libav which allow the encoding of
multimedia streams.
When you configure your Libav build, all the supported native encoders
are enabled by default. Encoders requiring an external library must be
enabled manually via the corresponding "--enable-lib" option. You can
list all available encoders using the configure option
"--list-encoders".
You can disable all the encoders with the configure option
"--disable-encoders" and selectively enable / disable single encoders
with the options "--enable-encoder=ENCODER" /
"--disable-encoder=ENCODER".
The option "-encoders" of the av* tools will display the list of
enabled encoders.
A description of some of the currently available audio encoders
follows.
ac3 and ac3_fixed
AC-3 audio encoders.
These encoders implement part of ATSC A/52:2010 and ETSI TS 102 366, as
well as the undocumented RealAudio 3 (a.k.a. dnet).
The ac3 encoder uses floating-point math, while the ac3_fixed encoder
only uses fixed-point integer math. This does not mean that one is
always faster, just that one or the other may be better suited to a
particular system. The floating-point encoder will generally produce
better quality audio for a given bitrate. The ac3_fixed encoder is not
the default codec for any of the output formats, so it must be
specified explicitly using the option "-acodec ac3_fixed" in order to
use it.
AC-3 Metadata
The AC-3 metadata options are used to set parameters that describe the
audio, but in most cases do not affect the audio encoding itself. Some
of the options do directly affect or influence the decoding and
playback of the resulting bitstream, while others are just for
informational purposes. A few of the options will add bits to the
output stream that could otherwise be used for audio data, and will
thus affect the quality of the output. Those will be indicated
accordingly with a note in the option list below.
These parameters are described in detail in several publicly-available
documents.
*<A/52:2010 - Digital Audio Compression (AC-3) (E-AC-3) Standard
("http://www.atsc.org/cms/standards/a_52-2010.pdf")>
*<A/54 - Guide to the Use of the ATSC Digital Television Standard
("http://www.atsc.org/cms/standards/a_54a_with_corr_1.pdf")>
*<Dolby Metadata Guide
("http://www.dolby.com/uploadedFiles/zz-_Shared_Assets/English_PDFs/Professional/18_Metadata.Guide.pdf")>
*<Dolby Digital Professional Encoding Guidelines
("http://www.dolby.com/uploadedFiles/zz-_Shared_Assets/English_PDFs/Professional/46_DDEncodingGuidelines.pdf")>
Metadata Control Options
-per_frame_metadata boolean
Allow Per-Frame Metadata. Specifies if the encoder should check for
changing metadata for each frame.
0 The metadata values set at initialization will be used for
every frame in the stream. (default)
1 Metadata values can be changed before encoding each frame.
Downmix Levels
-center_mixlev level
Center Mix Level. The amount of gain the decoder should apply to
the center channel when downmixing to stereo. This field will only
be written to the bitstream if a center channel is present. The
value is specified as a scale factor. There are 3 valid values:
0.707
Apply -3dB gain
0.595
Apply -4.5dB gain (default)
0.500
Apply -6dB gain
-surround_mixlev level
Surround Mix Level. The amount of gain the decoder should apply to
the surround channel(s) when downmixing to stereo. This field will
only be written to the bitstream if one or more surround channels
are present. The value is specified as a scale factor. There are 3
valid values:
0.707
Apply -3dB gain
0.500
Apply -6dB gain (default)
0.000
Silence Surround Channel(s)
Audio Production Information
Audio Production Information is optional information describing the
mixing environment. Either none or both of the fields are written to
the bitstream.
-mixing_level number
Mixing Level. Specifies peak sound pressure level (SPL) in the
production environment when the mix was mastered. Valid values are
80 to 111, or -1 for unknown or not indicated. The default value is
-1, but that value cannot be used if the Audio Production
Information is written to the bitstream. Therefore, if the
"room_type" option is not the default value, the "mixing_level"
option must not be -1.
-room_type type
Room Type. Describes the equalization used during the final mixing
session at the studio or on the dubbing stage. A large room is a
dubbing stage with the industry standard X-curve equalization; a
small room has flat equalization. This field will not be written
to the bitstream if both the "mixing_level" option and the
"room_type" option have the default values.
0
notindicated
Not Indicated (default)
1
large
Large Room
2
small
Small Room
Other Metadata Options
-copyright boolean
Copyright Indicator. Specifies whether a copyright exists for this
audio.
0
off No Copyright Exists (default)
1
on Copyright Exists
-dialnorm value
Dialogue Normalization. Indicates how far the average dialogue
level of the program is below digital 100% full scale (0 dBFS).
This parameter determines a level shift during audio reproduction
that sets the average volume of the dialogue to a preset level. The
goal is to match volume level between program sources. A value of
-31dB will result in no volume level change, relative to the source
volume, during audio reproduction. Valid values are whole numbers
in the range -31 to -1, with -31 being the default.
-dsur_mode mode
Dolby Surround Mode. Specifies whether the stereo signal uses Dolby
Surround (Pro Logic). This field will only be written to the
bitstream if the audio stream is stereo. Using this option does NOT
mean the encoder will actually apply Dolby Surround processing.
0
notindicated
Not Indicated (default)
1
off Not Dolby Surround Encoded
2
on Dolby Surround Encoded
-original boolean
Original Bit Stream Indicator. Specifies whether this audio is from
the original source and not a copy.
0
off Not Original Source
1
on Original Source (default)
Extended Bitstream Information
The extended bitstream options are part of the Alternate Bit Stream
Syntax as specified in Annex D of the A/52:2010 standard. It is grouped
into 2 parts. If any one parameter in a group is specified, all values
in that group will be written to the bitstream. Default values are
used for those that are written but have not been specified. If the
mixing levels are written, the decoder will use these values instead of
the ones specified in the "center_mixlev" and "surround_mixlev" options
if it supports the Alternate Bit Stream Syntax.
Extended Bitstream Information - Part 1
-dmix_mode mode
Preferred Stereo Downmix Mode. Allows the user to select either
Lt/Rt (Dolby Surround) or Lo/Ro (normal stereo) as the preferred
stereo downmix mode.
0
notindicated
Not Indicated (default)
1
ltrt
Lt/Rt Downmix Preferred
2
loro
Lo/Ro Downmix Preferred
-ltrt_cmixlev level
Lt/Rt Center Mix Level. The amount of gain the decoder should apply
to the center channel when downmixing to stereo in Lt/Rt mode.
1.414
Apply +3dB gain
1.189
Apply +1.5dB gain
1.000
Apply 0dB gain
0.841
Apply -1.5dB gain
0.707
Apply -3.0dB gain
0.595
Apply -4.5dB gain (default)
0.500
Apply -6.0dB gain
0.000
Silence Center Channel
-ltrt_surmixlev level
Lt/Rt Surround Mix Level. The amount of gain the decoder should
apply to the surround channel(s) when downmixing to stereo in Lt/Rt
mode.
0.841
Apply -1.5dB gain
0.707
Apply -3.0dB gain
0.595
Apply -4.5dB gain
0.500
Apply -6.0dB gain (default)
0.000
Silence Surround Channel(s)
-loro_cmixlev level
Lo/Ro Center Mix Level. The amount of gain the decoder should apply
to the center channel when downmixing to stereo in Lo/Ro mode.
1.414
Apply +3dB gain
1.189
Apply +1.5dB gain
1.000
Apply 0dB gain
0.841
Apply -1.5dB gain
0.707
Apply -3.0dB gain
0.595
Apply -4.5dB gain (default)
0.500
Apply -6.0dB gain
0.000
Silence Center Channel
-loro_surmixlev level
Lo/Ro Surround Mix Level. The amount of gain the decoder should
apply to the surround channel(s) when downmixing to stereo in Lo/Ro
mode.
0.841
Apply -1.5dB gain
0.707
Apply -3.0dB gain
0.595
Apply -4.5dB gain
0.500
Apply -6.0dB gain (default)
0.000
Silence Surround Channel(s)
Extended Bitstream Information - Part 2
-dsurex_mode mode
Dolby Surround EX Mode. Indicates whether the stream uses Dolby
Surround EX (7.1 matrixed to 5.1). Using this option does NOT mean
the encoder will actually apply Dolby Surround EX processing.
0
notindicated
Not Indicated (default)
1
on Dolby Surround EX Off
2
off Dolby Surround EX On
-dheadphone_mode mode
Dolby Headphone Mode. Indicates whether the stream uses Dolby
Headphone encoding (multi-channel matrixed to 2.0 for use with
headphones). Using this option does NOT mean the encoder will
actually apply Dolby Headphone processing.
0
notindicated
Not Indicated (default)
1
on Dolby Headphone Off
2
off Dolby Headphone On
-ad_conv_type type
A/D Converter Type. Indicates whether the audio has passed through
HDCD A/D conversion.
0
standard
Standard A/D Converter (default)
1
hdcd
HDCD A/D Converter
Other AC-3 Encoding Options
-stereo_rematrixing boolean
Stereo Rematrixing. Enables/Disables use of rematrixing for stereo
input. This is an optional AC-3 feature that increases quality by
selectively encoding the left/right channels as mid/side. This
option is enabled by default, and it is highly recommended that it
be left as enabled except for testing purposes.
Floating-Point-Only AC-3 Encoding Options
These options are only valid for the floating-point encoder and do not
exist for the fixed-point encoder due to the corresponding features not
being implemented in fixed-point.
-channel_coupling boolean
Enables/Disables use of channel coupling, which is an optional AC-3
feature that increases quality by combining high frequency
information from multiple channels into a single channel. The per-
channel high frequency information is sent with less accuracy in
both the frequency and time domains. This allows more bits to be
used for lower frequencies while preserving enough information to
reconstruct the high frequencies. This option is enabled by default
for the floating-point encoder and should generally be left as
enabled except for testing purposes or to increase encoding speed.
-1
auto
Selected by Encoder (default)
0
off Disable Channel Coupling
1
on Enable Channel Coupling
-cpl_start_band number
Coupling Start Band. Sets the channel coupling start band, from 1
to 15. If a value higher than the bandwidth is used, it will be
reduced to 1 less than the coupling end band. If auto is used, the
start band will be determined by the encoder based on the bit rate,
sample rate, and channel layout. This option has no effect if
channel coupling is disabled.
-1
auto
Selected by Encoder (default)
libwavpack
A wrapper providing WavPack encoding through libwavpack.
Only lossless mode using 32-bit integer samples is supported currently.
The compression_level option can be used to control speed vs.
compression tradeoff, with the values mapped to libwavpack as follows:
0 Fast mode - corresponding to the wavpack -f option.
1 Normal (default) settings.
2 High quality - corresponding to the wavpack -h option.
3 Very high quality - corresponding to the wavpack -hh option.
4-8 Same as 3, but with extra processing enabled - corresponding to the
wavpack -x option. I.e. 4 is the same as -x2 and 8 is the same as
-x6.
libwebp
libwebp WebP Image encoder wrapper
libwebp is Google's official encoder for WebP images. It can encode in
either lossy or lossless mode. Lossy images are essentially a wrapper
around a VP8 frame. Lossless images are a separate codec developed by
Google.
Pixel Format
Currently, libwebp only supports YUV420 for lossy and RGB for lossless
due to limitations of the format and libwebp. Alpha is supported for
either mode. Because of API limitations, if RGB is passed in when
encoding lossy or YUV is passed in for encoding lossless, the pixel
format will automatically be converted using functions from libwebp.
This is not ideal and is done only for convenience.
Options
-lossless boolean
Enables/Disables use of lossless mode. Default is 0.
-compression_level integer
For lossy, this is a quality/speed tradeoff. Higher values give
better quality for a given size at the cost of increased encoding
time. For lossless, this is a size/speed tradeoff. Higher values
give smaller size at the cost of increased encoding time. More
specifically, it controls the number of extra algorithms and
compression tools used, and varies the combination of these tools.
This maps to the method option in libwebp. The valid range is 0 to
6. Default is 4.
-qscale float
For lossy encoding, this controls image quality, 0 to 100. For
lossless encoding, this controls the effort and time spent at
compressing more. The default value is 75. Note that for usage via
libavcodec, this option is called global_quality and must be
multiplied by FF_QP2LAMBDA.
-preset type
Configuration preset. This does some automatic settings based on
the general type of the image.
none
Do not use a preset.
default
Use the encoder default.
picture
Digital picture, like portrait, inner shot
photo
Outdoor photograph, with natural lighting
drawing
Hand or line drawing, with high-contrast details
icon
Small-sized colorful images
text
Text-like
lumi_aq
Enable lumi masking adaptive quantization when set to 1. Default is
0 (disabled).
variance_aq
Enable variance adaptive quantization when set to 1. Default is 0
(disabled).
When combined with lumi_aq, the resulting quality will not be
better than any of the two specified individually. In other words,
the resulting quality will be the worse one of the two effects.
ssim
Set structural similarity (SSIM) displaying method. Possible
values:
off Disable displaying of SSIM information.
avg Output average SSIM at the end of encoding to stdout. The
format of showing the average SSIM is:
Average SSIM: %f
For users who are not familiar with C, %f means a float number,
or a decimal (e.g. 0.939232).
frame
Output both per-frame SSIM data during encoding and average
SSIM at the end of encoding to stdout. The format of per-frame
information is:
SSIM: avg: %1.3f min: %1.3f max: %1.3f
For users who are not familiar with C, %1.3f means a float
number rounded to 3 digits after the dot (e.g. 0.932).
ssim_acc
Set SSIM accuracy. Valid options are integers within the range of
0-4, while 0 gives the most accurate result and 4 computes the
fastest.
libx264
x264 H.264/MPEG-4 AVC encoder wrapper
x264 supports an impressive number of features, including 8x8 and 4x4
adaptive spatial transform, adaptive B-frame placement, CAVLC/CABAC
entropy coding, interlacing (MBAFF), lossless mode, psy optimizations
for detail retention (adaptive quantization, psy-RD, psy-trellis).
The Libav wrapper provides a mapping for most of them using global
options that match those of the encoders and provides private options
for the unique encoder options. Additionally an expert override is
provided to directly pass a list of key=value tuples as accepted by
x264_param_parse.
Option Mapping
The following options are supported by the x264 wrapper, the
x264-equivalent options follow the Libav ones.
b : bitrate
Libav "b" option is expressed in bits/s, x264 "bitrate" in
kilobits/s.
bf : bframes
Maximum number of B-frames.
g : keyint
Maximum GOP size.
qmin : qpmin
Minimum quantizer scale.
qmax : qpmax
Maximum quantizer scale.
qdiff : qpstep
Maximum difference between quantizer scales.
qblur : qblur
Quantizer curve blur
qcomp : qcomp
Quantizer curve compression factor
refs : ref
Number of reference frames each P-frame can use. The range is from
0-16.
sc_threshold : scenecut
Sets the threshold for the scene change detection.
trellis : trellis
Performs Trellis quantization to increase efficiency. Enabled by
default.
nr : nr
Noise reduction.
me_range : merange
Maximum range of the motion search in pixels.
me_method : me
Full-pixel motion estimation method.
subq : subme
Sub-pixel motion estimation method.
b_strategy : b-adapt
Adaptive B-frame placement decision algorithm. Use only on first-
pass.
keyint_min : min-keyint
Minimum GOP size.
coder : cabac
Set coder to "ac" to use CABAC.
cmp : chroma-me
Set to "chroma" to use chroma motion estimation.
threads : threads
Number of encoding threads.
thread_type : sliced_threads
Set to "slice" to use sliced threading instead of frame threading.
flags -cgop : open-gop
Set "-cgop" to use recovery points to close GOPs.
rc_init_occupancy : vbv-init
Initial buffer occupancy.
Private Options
-preset string
Set the encoding preset (cf. x264 --fullhelp).
-tune string
Tune the encoding params (cf. x264 --fullhelp).
-profile string
Set profile restrictions (cf. x264 --fullhelp).
-fastfirstpass integer
Use fast settings when encoding first pass.
-crf float
Select the quality for constant quality mode.
-crf_max float
In CRF mode, prevents VBV from lowering quality beyond this point.
-qp integer
Constant quantization parameter rate control method.
-aq-mode integer
AQ method
Possible values:
none
variance
Variance AQ (complexity mask).
autovariance
Auto-variance AQ (experimental).
-aq-strength float
AQ strength, reduces blocking and blurring in flat and textured
areas.
-psy integer
Use psychovisual optimizations.
-psy-rd string
Strength of psychovisual optimization, in <psy-rd>:<psy-trellis>
format.
-rc-lookahead integer
Number of frames to look ahead for frametype and ratecontrol.
-weightb integer
Weighted prediction for B-frames.
-weightp integer
Weighted prediction analysis method.
Possible values:
none
simple
smart
-ssim integer
Calculate and print SSIM stats.
-intra-refresh integer
Use Periodic Intra Refresh instead of IDR frames.
-bluray-compat integer
Configure the encoder to be compatible with the bluray standard.
It is a shorthand for setting "bluray-compat=1 force-cfr=1".
-b-bias integer
Influences how often B-frames are used.
-b-pyramid integer
Keep some B-frames as references.
Possible values:
none
strict
Strictly hierarchical pyramid.
normal
Non-strict (not Blu-ray compatible).
-mixed-refs integer
One reference per partition, as opposed to one reference per
macroblock.
-8x8dct integer
High profile 8x8 transform.
-fast-pskip integer
-aud integer
Use access unit delimiters.
-mbtree integer
Use macroblock tree ratecontrol.
-deblock string
Loop filter parameters, in <alpha:beta> form.
-cplxblur float
Reduce fluctuations in QP (before curve compression).
-partitions string
A comma-separated list of partitions to consider, possible values:
p8x8, p4x4, b8x8, i8x8, i4x4, none, all.
-direct-pred integer
Direct MV prediction mode
Possible values:
none
spatial
temporal
auto
-slice-max-size integer
Limit the size of each slice in bytes.
-stats string
Filename for 2 pass stats.
-nal-hrd integer
Signal HRD information (requires vbv-bufsize; cbr not allowed in
.mp4).
Possible values:
none
vbr
cbr
-x264-params string
Override the x264 configuration using a :-separated list of
key=value parameters.
-x264-params level=30:bframes=0:weightp=0:cabac=0:ref=1:vbv-maxrate=768:vbv-bufsize=2000:analyse=all:me=umh:no-fast-pskip=1:subq=6:8x8dct=0:trellis=0
Encoding avpresets for common usages are provided so they can be used
with the general presets system (e.g. passing the "-pre" option).
ProRes
Apple ProRes encoder.
Private Options
profile integer
Select the ProRes profile to encode
proxy
lt
standard
hq
4444
quant_mat integer
Select quantization matrix.
auto
default
proxy
lt
standard
hq
If set to auto, the matrix matching the profile will be picked. If
not set, the matrix providing the highest quality, default, will be
picked.
bits_per_mb integer
How many bits to allot for coding one macroblock. Different
profiles use between 200 and 2400 bits per macroblock, the maximum
is 8000.
mbs_per_slice integer
Number of macroblocks in each slice (1-8); the default value (8)
should be good in almost all situations.
vendor string
Override the 4-byte vendor ID. A custom vendor ID like apl0 would
claim the stream was produced by the Apple encoder.
alpha_bits integer
Specify number of bits for alpha component. Possible values are 0,
8 and 16. Use 0 to disable alpha plane coding.
Speed considerations
In the default mode of operation the encoder has to honor frame
constraints (i.e. not produc frames with size bigger than requested)
while still making output picture as good as possible. A frame
containing a lot of small details is harder to compress and the encoder
would spend more time searching for appropriate quantizers for each
slice.
Setting a higher bits_per_mb limit will improve the speed.
For the fastest encoding speed set the qscale parameter (4 is the
recommended value) and do not set a size constraint.
Demuxers are configured elements in Libav which allow to read the
multimedia streams from a particular type of file.
When you configure your Libav build, all the supported demuxers are
enabled by default. You can list all available ones using the configure
option "--list-demuxers".
You can disable all the demuxers using the configure option
"--disable-demuxers", and selectively enable a single demuxer with the
option "--enable-demuxer=DEMUXER", or disable it with the option
"--disable-demuxer=DEMUXER".
The option "-formats" of the av* tools will display the list of enabled
demuxers.
The description of some of the currently available demuxers follows.
image2
Image file demuxer.
This demuxer reads from a list of image files specified by a pattern.
The pattern may contain the string "%d" or "%0Nd", which specifies the
position of the characters representing a sequential number in each
filename matched by the pattern. If the form "%d0Nd" is used, the
string representing the number in each filename is 0-padded and N is
the total number of 0-padded digits representing the number. The
literal character '%' can be specified in the pattern with the string
"%%".
If the pattern contains "%d" or "%0Nd", the first filename of the file
list specified by the pattern must contain a number inclusively
contained between 0 and 4, all the following numbers must be
sequential. This limitation may be hopefully fixed.
The pattern may contain a suffix which is used to automatically
determine the format of the images contained in the files.
For example the pattern "img-%03d.bmp" will match a sequence of
filenames of the form img-001.bmp, img-002.bmp, ..., img-010.bmp, etc.;
the pattern "i%%m%%g-%d.jpg" will match a sequence of filenames of the
form i%m%g-1.jpg, i%m%g-2.jpg, ..., i%m%g-10.jpg, etc.
The size, the pixel format, and the format of each image must be the
same for all the files in the sequence.
The following example shows how to use avconv for creating a video from
the images in the file sequence img-001.jpeg, img-002.jpeg, ...,
assuming an input framerate of 10 frames per second:
avconv -i 'img-%03d.jpeg' -r 10 out.mkv
Note that the pattern must not necessarily contain "%d" or "%0Nd", for
example to convert a single image file img.jpeg you can employ the
command:
avconv -i img.jpeg img.png
-pixel_format format
Set the pixel format (for raw image)
-video_size size
Set the frame size (for raw image)
-framerate rate
Set the frame rate
-loop bool
Loop over the images
-start_number start
Specify the first number in the sequence
applehttp
Apple HTTP Live Streaming demuxer.
This demuxer presents all AVStreams from all variant streams. The id
field is set to the bitrate variant index number. By setting the
discard flags on AVStreams (by pressing 'a' or 'v' in avplay), the
caller can decide which variant streams to actually receive. The total
bitrate of the variant that the stream belongs to is available in a
metadata key named "variant_bitrate".
flv
Adobe Flash Video Format demuxer.
This demuxer is used to demux FLV files and RTMP network streams.
-flv_metadata bool
Allocate the streams according to the onMetaData array content.
asf
Advanced Systems Format demuxer.
This demuxer is used to demux ASF files and MMS network streams.
-no_resync_search bool
Do not try to resynchronize by looking for a certain optional start
code.
Muxers are configured elements in Libav which allow writing multimedia
streams to a particular type of file.
When you configure your Libav build, all the supported muxers are
enabled by default. You can list all available muxers using the
configure option "--list-muxers".
You can disable all the muxers with the configure option
"--disable-muxers" and selectively enable / disable single muxers with
the options "--enable-muxer=MUXER" / "--disable-muxer=MUXER".
The option "-formats" of the av* tools will display the list of enabled
muxers.
A description of some of the currently available muxers follows.
crc
CRC (Cyclic Redundancy Check) testing format.
This muxer computes and prints the Adler-32 CRC of all the input audio
and video frames. By default audio frames are converted to signed
16-bit raw audio and video frames to raw video before computing the
CRC.
The output of the muxer consists of a single line of the form:
CRC=0xCRC, where CRC is a hexadecimal number 0-padded to 8 digits
containing the CRC for all the decoded input frames.
For example to compute the CRC of the input, and store it in the file
out.crc:
avconv -i INPUT -f crc out.crc
You can print the CRC to stdout with the command:
avconv -i INPUT -f crc -
You can select the output format of each frame with avconv by
specifying the audio and video codec and format. For example to compute
the CRC of the input audio converted to PCM unsigned 8-bit and the
input video converted to MPEG-2 video, use the command:
avconv -i INPUT -c:a pcm_u8 -c:v mpeg2video -f crc -
See also the framecrc muxer.
framecrc
Per-frame CRC (Cyclic Redundancy Check) testing format.
This muxer computes and prints the Adler-32 CRC for each decoded audio
and video frame. By default audio frames are converted to signed 16-bit
raw audio and video frames to raw video before computing the CRC.
The output of the muxer consists of a line for each audio and video
frame of the form: stream_index, frame_dts, frame_size, 0xCRC, where
CRC is a hexadecimal number 0-padded to 8 digits containing the CRC of
the decoded frame.
For example to compute the CRC of each decoded frame in the input, and
store it in the file out.crc:
avconv -i INPUT -f framecrc out.crc
You can print the CRC of each decoded frame to stdout with the command:
avconv -i INPUT -f framecrc -
You can select the output format of each frame with avconv by
specifying the audio and video codec and format. For example, to
compute the CRC of each decoded input audio frame converted to PCM
unsigned 8-bit and of each decoded input video frame converted to
MPEG-2 video, use the command:
avconv -i INPUT -c:a pcm_u8 -c:v mpeg2video -f framecrc -
See also the crc muxer.
hls
Apple HTTP Live Streaming muxer that segments MPEG-TS according to the
HTTP Live Streaming specification.
It creates a playlist file and numbered segment files. The output
filename specifies the playlist filename; the segment filenames receive
the same basename as the playlist, a sequential number and a .ts
extension.
avconv -i in.nut out.m3u8
-hls_time seconds
Set the segment length in seconds.
-hls_list_size size
Set the maximum number of playlist entries.
-hls_wrap wrap
Set the number after which index wraps.
-start_number number
Start the sequence from number.
-hls_base_url baseurl
Append baseurl to every entry in the playlist. Useful to generate
playlists with absolute paths.
image2
Image file muxer.
The image file muxer writes video frames to image files.
The output filenames are specified by a pattern, which can be used to
produce sequentially numbered series of files. The pattern may contain
the string "%d" or "%0Nd", this string specifies the position of the
characters representing a numbering in the filenames. If the form
"%0Nd" is used, the string representing the number in each filename is
0-padded to N digits. The literal character '%' can be specified in the
pattern with the string "%%".
If the pattern contains "%d" or "%0Nd", the first filename of the file
list specified will contain the number 1, all the following numbers
will be sequential.
The pattern may contain a suffix which is used to automatically
determine the format of the image files to write.
For example the pattern "img-%03d.bmp" will specify a sequence of
filenames of the form img-001.bmp, img-002.bmp, ..., img-010.bmp, etc.
The pattern "img%%-%d.jpg" will specify a sequence of filenames of the
form img%-1.jpg, img%-2.jpg, ..., img%-10.jpg, etc.
The following example shows how to use avconv for creating a sequence
of files img-001.jpeg, img-002.jpeg, ..., taking one image every second
from the input video:
avconv -i in.avi -vsync 1 -r 1 -f image2 'img-%03d.jpeg'
Note that with avconv, if the format is not specified with the "-f"
option and the output filename specifies an image file format, the
image2 muxer is automatically selected, so the previous command can be
written as:
avconv -i in.avi -vsync 1 -r 1 'img-%03d.jpeg'
Note also that the pattern must not necessarily contain "%d" or "%0Nd",
for example to create a single image file img.jpeg from the input video
you can employ the command:
avconv -i in.avi -f image2 -frames:v 1 img.jpeg
-start_number number
Start the sequence from number.
-update number
If number is nonzero, the filename will always be interpreted as
just a filename, not a pattern, and this file will be continuously
overwritten with new images.
matroska
Matroska container muxer.
This muxer implements the matroska and webm container specs.
The recognized metadata settings in this muxer are:
title=title name
Name provided to a single track
language=language name
Specifies the language of the track in the Matroska languages form
STEREO_MODE=mode
Stereo 3D video layout of two views in a single video track
mono
video is not stereo
left_right
Both views are arranged side by side, Left-eye view is on the
left
bottom_top
Both views are arranged in top-bottom orientation, Left-eye
view is at bottom
top_bottom
Both views are arranged in top-bottom orientation, Left-eye
view is on top
checkerboard_rl
Each view is arranged in a checkerboard interleaved pattern,
Left-eye view being first
checkerboard_lr
Each view is arranged in a checkerboard interleaved pattern,
Right-eye view being first
row_interleaved_rl
Each view is constituted by a row based interleaving, Right-eye
view is first row
row_interleaved_lr
Each view is constituted by a row based interleaving, Left-eye
view is first row
col_interleaved_rl
Both views are arranged in a column based interleaving manner,
Right-eye view is first column
col_interleaved_lr
Both views are arranged in a column based interleaving manner,
Left-eye view is first column
anaglyph_cyan_red
All frames are in anaglyph format viewable through red-cyan
filters
right_left
Both views are arranged side by side, Right-eye view is on the
left
anaglyph_green_magenta
All frames are in anaglyph format viewable through green-
magenta filters
block_lr
Both eyes laced in one Block, Left-eye view is first
block_rl
Both eyes laced in one Block, Right-eye view is first
For example a 3D WebM clip can be created using the following command
line:
avconv -i sample_left_right_clip.mpg -an -c:v libvpx -metadata STEREO_MODE=left_right -y stereo_clip.webm
This muxer supports the following options:
reserve_index_space
By default, this muxer writes the index for seeking (called cues in
Matroska terms) at the end of the file, because it cannot know in
advance how much space to leave for the index at the beginning of
the file. However for some use cases -- e.g. streaming where
seeking is possible but slow -- it is useful to put the index at
the beginning of the file.
If this option is set to a non-zero value, the muxer will reserve a
given amount of space in the file header and then try to write the
cues there when the muxing finishes. If the available space does
not suffice, muxing will fail. A safe size for most use cases
should be about 50kB per hour of video.
Note that cues are only written if the output is seekable and this
option will have no effect if it is not.
mov, mp4, ismv
The mov/mp4/ismv muxer supports fragmentation. Normally, a MOV/MP4 file
has all the metadata about all packets stored in one location (written
at the end of the file, it can be moved to the start for better
playback using the qt-faststart tool). A fragmented file consists of a
number of fragments, where packets and metadata about these packets are
stored together. Writing a fragmented file has the advantage that the
file is decodable even if the writing is interrupted (while a normal
MOV/MP4 is undecodable if it is not properly finished), and it requires
less memory when writing very long files (since writing normal MOV/MP4
files stores info about every single packet in memory until the file is
closed). The downside is that it is less compatible with other
applications.
Fragmentation is enabled by setting one of the AVOptions that define
how to cut the file into fragments:
-movflags frag_keyframe
Start a new fragment at each video keyframe.
-frag_duration duration
Create fragments that are duration microseconds long.
-frag_size size
Create fragments that contain up to size bytes of payload data.
-movflags frag_custom
Allow the caller to manually choose when to cut fragments, by
calling "av_write_frame(ctx, NULL)" to write a fragment with the
packets written so far. (This is only useful with other
applications integrating libavformat, not from avconv.)
-min_frag_duration duration
Don't create fragments that are shorter than duration microseconds
long.
If more than one condition is specified, fragments are cut when one of
the specified conditions is fulfilled. The exception to this is
"-min_frag_duration", which has to be fulfilled for any of the other
conditions to apply.
Additionally, the way the output file is written can be adjusted
through a few other options:
-movflags empty_moov
Write an initial moov atom directly at the start of the file,
without describing any samples in it. Generally, an mdat/moov pair
is written at the start of the file, as a normal MOV/MP4 file,
containing only a short portion of the file. With this option set,
there is no initial mdat atom, and the moov atom only describes the
tracks but has a zero duration.
Files written with this option set do not work in QuickTime. This
option is implicitly set when writing ismv (Smooth Streaming)
files.
-movflags separate_moof
Write a separate moof (movie fragment) atom for each track.
Normally, packets for all tracks are written in a moof atom (which
is slightly more efficient), but with this option set, the muxer
writes one moof/mdat pair for each track, making it easier to
separate tracks.
This option is implicitly set when writing ismv (Smooth Streaming)
files.
-movflags faststart
Run a second pass moving the index (moov atom) to the beginning of
the file. This operation can take a while, and will not work in
various situations such as fragmented output, thus it is not
enabled by default.
-movflags disable_chpl
Disable Nero chapter markers (chpl atom). Normally, both Nero
chapters and a QuickTime chapter track are written to the file.
With this option set, only the QuickTime chapter track will be
written. Nero chapters can cause failures when the file is
reprocessed with certain tagging programs.
Smooth Streaming content can be pushed in real time to a publishing
point on IIS with this muxer. Example:
avconv -re <<normal input/transcoding options>> -movflags isml+frag_keyframe -f ismv http://server/publishingpoint.isml/Streams(Encoder1)
mp3
The MP3 muxer writes a raw MP3 stream with an ID3v2 header at the
beginning and optionally an ID3v1 tag at the end. ID3v2.3 and ID3v2.4
are supported, the "id3v2_version" option controls which one is used.
Setting "id3v2_version" to 0 will disable the ID3v2 header completely.
The legacy ID3v1 tag is not written by default, but may be enabled with
the "write_id3v1" option.
The muxer may also write a Xing frame at the beginning, which contains
the number of frames in the file. It is useful for computing duration
of VBR files. The Xing frame is written if the output stream is
seekable and if the "write_xing" option is set to 1 (the default).
The muxer supports writing ID3v2 attached pictures (APIC frames). The
pictures are supplied to the muxer in form of a video stream with a
single packet. There can be any number of those streams, each will
correspond to a single APIC frame. The stream metadata tags title and
comment map to APIC description and picture type respectively. See
<http://id3.org/id3v2.4.0-frames> for allowed picture types.
Note that the APIC frames must be written at the beginning, so the
muxer will buffer the audio frames until it gets all the pictures. It
is therefore advised to provide the pictures as soon as possible to
avoid excessive buffering.
Examples:
Write an mp3 with an ID3v2.3 header and an ID3v1 footer:
avconv -i INPUT -id3v2_version 3 -write_id3v1 1 out.mp3
Attach a picture to an mp3:
avconv -i input.mp3 -i cover.png -c copy -metadata:s:v title="Album cover"
-metadata:s:v comment="Cover (Front)" out.mp3
Write a "clean" MP3 without any extra features:
avconv -i input.wav -write_xing 0 -id3v2_version 0 out.mp3
mpegts
MPEG transport stream muxer.
This muxer implements ISO 13818-1 and part of ETSI EN 300 468.
The muxer options are:
-mpegts_original_network_id number
Set the original_network_id (default 0x0001). This is unique
identifier of a network in DVB. Its main use is in the unique
identification of a service through the path Original_Network_ID,
Transport_Stream_ID.
-mpegts_transport_stream_id number
Set the transport_stream_id (default 0x0001). This identifies a
transponder in DVB.
-mpegts_service_id number
Set the service_id (default 0x0001) also known as program in DVB.
-mpegts_pmt_start_pid number
Set the first PID for PMT (default 0x1000, max 0x1f00).
-mpegts_start_pid number
Set the first PID for data packets (default 0x0100, max 0x0f00).
-muxrate number
Set a constant muxrate (default VBR).
-pcr_period numer
Override the default PCR retransmission time (default 20ms),
ignored if variable muxrate is selected.
The recognized metadata settings in mpegts muxer are "service_provider"
and "service_name". If they are not set the default for
"service_provider" is "Libav" and the default for "service_name" is
"Service01".
avconv -i file.mpg -c copy \
-mpegts_original_network_id 0x1122 \
-mpegts_transport_stream_id 0x3344 \
-mpegts_service_id 0x5566 \
-mpegts_pmt_start_pid 0x1500 \
-mpegts_start_pid 0x150 \
-metadata service_provider="Some provider" \
-metadata service_name="Some Channel" \
-y out.ts
null
Null muxer.
This muxer does not generate any output file, it is mainly useful for
testing or benchmarking purposes.
For example to benchmark decoding with avconv you can use the command:
avconv -benchmark -i INPUT -f null out.null
Note that the above command does not read or write the out.null file,
but specifying the output file is required by the avconv syntax.
Alternatively you can write the command as:
avconv -benchmark -i INPUT -f null -
nut
-syncpoints flags
Change the syncpoint usage in nut:
default use the normal low-overhead seeking aids.
none do not use the syncpoints at all, reducing the overhead but
making the stream non-seekable;
timestamped extend the syncpoint with a wallclock field.
The none and timestamped flags are experimental.
avconv -i INPUT -f_strict experimental -syncpoints none - | processor
ogg
Ogg container muxer.
-page_duration duration
Preferred page duration, in microseconds. The muxer will attempt to
create pages that are approximately duration microseconds long.
This allows the user to compromise between seek granularity and
container overhead. The default is 1 second. A value of 0 will fill
all segments, making pages as large as possible. A value of 1 will
effectively use 1 packet-per-page in most situations, giving a
small seek granularity at the cost of additional container
overhead.
segment
Basic stream segmenter.
The segmenter muxer outputs streams to a number of separate files of
nearly fixed duration. Output filename pattern can be set in a fashion
similar to image2.
Every segment starts with a video keyframe, if a video stream is
present. The segment muxer works best with a single constant frame
rate video.
Optionally it can generate a flat list of the created segments, one
segment per line.
segment_format format
Override the inner container format, by default it is guessed by
the filename extension.
segment_time t
Set segment duration to t seconds.
segment_list name
Generate also a listfile named name.
segment_list_type type
Select the listing format.
flat use a simple flat list of entries.
hls use a m3u8-like structure.
segment_list_size size
Overwrite the listfile once it reaches size entries.
segment_list_entry_prefix prefix
Prepend prefix to each entry. Useful to generate absolute paths.
segment_wrap limit
Wrap around segment index once it reaches limit.
avconv -i in.mkv -c copy -map 0 -f segment -list out.list out%03d.nut
Input devices are configured elements in Libav which allow to access
the data coming from a multimedia device attached to your system.
When you configure your Libav build, all the supported input devices
are enabled by default. You can list all available ones using the
configure option "--list-indevs".
You can disable all the input devices using the configure option
"--disable-indevs", and selectively enable an input device using the
option "--enable-indev=INDEV", or you can disable a particular input
device using the option "--disable-indev=INDEV".
The option "-formats" of the av* tools will display the list of
supported input devices (amongst the demuxers).
A description of the currently available input devices follows.
alsa
ALSA (Advanced Linux Sound Architecture) input device.
To enable this input device during configuration you need libasound
installed on your system.
This device allows capturing from an ALSA device. The name of the
device to capture has to be an ALSA card identifier.
An ALSA identifier has the syntax:
hw:<CARD>[,<DEV>[,<SUBDEV>]]
where the DEV and SUBDEV components are optional.
The three arguments (in order: CARD,DEV,SUBDEV) specify card number or
identifier, device number and subdevice number (-1 means any).
To see the list of cards currently recognized by your system check the
files /proc/asound/cards and /proc/asound/devices.
For example to capture with avconv from an ALSA device with card id 0,
you may run the command:
avconv -f alsa -i hw:0 alsaout.wav
For more information see:
<http://www.alsa-project.org/alsa-doc/alsa-lib/pcm.html>
bktr
BSD video input device.
dv1394
Linux DV 1394 input device.
fbdev
Linux framebuffer input device.
The Linux framebuffer is a graphic hardware-independent abstraction
layer to show graphics on a computer monitor, typically on the console.
It is accessed through a file device node, usually /dev/fb0.
For more detailed information read the file
Documentation/fb/framebuffer.txt included in the Linux source tree.
To record from the framebuffer device /dev/fb0 with avconv:
avconv -f fbdev -r 10 -i /dev/fb0 out.avi
You can take a single screenshot image with the command:
avconv -f fbdev -frames:v 1 -r 1 -i /dev/fb0 screenshot.jpeg
See also <http://linux-fbdev.sourceforge.net/>, and fbset(1).
jack
JACK input device.
To enable this input device during configuration you need libjack
installed on your system.
A JACK input device creates one or more JACK writable clients, one for
each audio channel, with name client_name:input_N, where client_name is
the name provided by the application, and N is a number which
identifies the channel. Each writable client will send the acquired
data to the Libav input device.
Once you have created one or more JACK readable clients, you need to
connect them to one or more JACK writable clients.
To connect or disconnect JACK clients you can use the jack_connect and
jack_disconnect programs, or do it through a graphical interface, for
example with qjackctl.
To list the JACK clients and their properties you can invoke the
command jack_lsp.
Follows an example which shows how to capture a JACK readable client
with avconv.
# Create a JACK writable client with name "libav".
$ avconv -f jack -i libav -y out.wav
# Start the sample jack_metro readable client.
$ jack_metro -b 120 -d 0.2 -f 4000
# List the current JACK clients.
$ jack_lsp -c
system:capture_1
system:capture_2
system:playback_1
system:playback_2
libav:input_1
metro:120_bpm
# Connect metro to the avconv writable client.
$ jack_connect metro:120_bpm libav:input_1
For more information read: <http://jackaudio.org/>
libdc1394
IIDC1394 input device, based on libdc1394 and libraw1394.
oss
Open Sound System input device.
The filename to provide to the input device is the device node
representing the OSS input device, and is usually set to /dev/dsp.
For example to grab from /dev/dsp using avconv use the command:
avconv -f oss -i /dev/dsp /tmp/oss.wav
For more information about OSS see:
<http://manuals.opensound.com/usersguide/dsp.html>
pulse
pulseaudio input device.
To enable this input device during configuration you need libpulse-
simple installed in your system.
The filename to provide to the input device is a source device or the
string "default"
To list the pulse source devices and their properties you can invoke
the command pactl list sources.
avconv -f pulse -i default /tmp/pulse.wav
server AVOption
The syntax is:
-server <server name>
Connects to a specific server.
name AVOption
The syntax is:
-name <application name>
Specify the application name pulse will use when showing active
clients, by default it is "libav"
stream_name AVOption
The syntax is:
-stream_name <stream name>
Specify the stream name pulse will use when showing active streams, by
default it is "record"
sample_rate AVOption
The syntax is:
-sample_rate <samplerate>
Specify the samplerate in Hz, by default 48kHz is used.
channels AVOption
The syntax is:
-channels <N>
Specify the channels in use, by default 2 (stereo) is set.
frame_size AVOption
The syntax is:
-frame_size <bytes>
Specify the number of byte per frame, by default it is set to 1024.
fragment_size AVOption
The syntax is:
-fragment_size <bytes>
Specify the minimal buffering fragment in pulseaudio, it will affect
the audio latency. By default it is unset.
sndio
sndio input device.
To enable this input device during configuration you need libsndio
installed on your system.
The filename to provide to the input device is the device node
representing the sndio input device, and is usually set to /dev/audio0.
For example to grab from /dev/audio0 using avconv use the command:
avconv -f sndio -i /dev/audio0 /tmp/oss.wav
video4linux2
Video4Linux2 input video device.
The name of the device to grab is a file device node, usually Linux
systems tend to automatically create such nodes when the device (e.g.
an USB webcam) is plugged into the system, and has a name of the kind
/dev/videoN, where N is a number associated to the device.
Video4Linux2 devices usually support a limited set of widthxheight
sizes and framerates. You can check which are supported using
-list_formats all for Video4Linux2 devices.
Some usage examples of the video4linux2 devices with avconv and avplay:
# Grab and show the input of a video4linux2 device.
avplay -f video4linux2 -framerate 30 -video_size hd720 /dev/video0
# Grab and record the input of a video4linux2 device, leave the
framerate and size as previously set.
avconv -f video4linux2 -input_format mjpeg -i /dev/video0 out.mpeg
vfwcap
VfW (Video for Windows) capture input device.
The filename passed as input is the capture driver number, ranging from
0 to 9. You may use "list" as filename to print a list of drivers. Any
other filename will be interpreted as device number 0.
x11grab
X11 video input device.
This device allows to capture a region of an X11 display.
The filename passed as input has the syntax:
[<hostname>]:<display_number>.<screen_number>[+<x_offset>,<y_offset>]
hostname:display_number.screen_number specifies the X11 display name of
the screen to grab from. hostname can be omitted, and defaults to
"localhost". The environment variable DISPLAY contains the default
display name.
x_offset and y_offset specify the offsets of the grabbed area with
respect to the top-left border of the X11 screen. They default to 0.
Check the X11 documentation (e.g. man X) for more detailed information.
Use the dpyinfo program for getting basic information about the
properties of your X11 display (e.g. grep for "name" or "dimensions").
For example to grab from :0.0 using avconv:
avconv -f x11grab -r 25 -s cif -i :0.0 out.mpg
# Grab at position 10,20.
avconv -f x11grab -r 25 -s cif -i :0.0+10,20 out.mpg
follow_mouse AVOption
The syntax is:
-follow_mouse centered|<PIXELS>
When it is specified with "centered", the grabbing region follows the
mouse pointer and keeps the pointer at the center of region; otherwise,
the region follows only when the mouse pointer reaches within PIXELS
(greater than zero) to the edge of region.
For example:
avconv -f x11grab -follow_mouse centered -r 25 -s cif -i :0.0 out.mpg
# Follows only when the mouse pointer reaches within 100 pixels to edge
avconv -f x11grab -follow_mouse 100 -r 25 -s cif -i :0.0 out.mpg
show_region AVOption
The syntax is:
-show_region 1
If show_region AVOption is specified with 1, then the grabbing region
will be indicated on screen. With this option, it's easy to know what
is being grabbed if only a portion of the screen is grabbed.
For example:
avconv -f x11grab -show_region 1 -r 25 -s cif -i :0.0+10,20 out.mpg
# With follow_mouse
avconv -f x11grab -follow_mouse centered -show_region 1 -r 25 -s cif -i :0.0 out.mpg
Output devices are configured elements in Libav which allow to write
multimedia data to an output device attached to your system.
When you configure your Libav build, all the supported output devices
are enabled by default. You can list all available ones using the
configure option "--list-outdevs".
You can disable all the output devices using the configure option
"--disable-outdevs", and selectively enable an output device using the
option "--enable-outdev=OUTDEV", or you can disable a particular input
device using the option "--disable-outdev=OUTDEV".
The option "-formats" of the av* tools will display the list of enabled
output devices (amongst the muxers).
A description of the currently available output devices follows.
alsa
ALSA (Advanced Linux Sound Architecture) output device.
oss
OSS (Open Sound System) output device.
sndio
sndio audio output device.
Protocols are configured elements in Libav which allow to access
resources which require the use of a particular protocol.
When you configure your Libav build, all the supported protocols are
enabled by default. You can list all available ones using the configure
option "--list-protocols".
You can disable all the protocols using the configure option
"--disable-protocols", and selectively enable a protocol using the
option "--enable-protocol=PROTOCOL", or you can disable a particular
protocol using the option "--disable-protocol=PROTOCOL".
The option "-protocols" of the av* tools will display the list of
supported protocols.
A description of the currently available protocols follows.
concat
Physical concatenation protocol.
Allow to read and seek from many resource in sequence as if they were a
unique resource.
A URL accepted by this protocol has the syntax:
concat:<URL1>|<URL2>|...|<URLN>
where URL1, URL2, ..., URLN are the urls of the resource to be
concatenated, each one possibly specifying a distinct protocol.
For example to read a sequence of files split1.mpeg, split2.mpeg,
split3.mpeg with avplay use the command:
avplay concat:split1.mpeg\|split2.mpeg\|split3.mpeg
Note that you may need to escape the character "|" which is special for
many shells.
file
File access protocol.
Allow to read from or read to a file.
For example to read from a file input.mpeg with avconv use the command:
avconv -i file:input.mpeg output.mpeg
The av* tools default to the file protocol, that is a resource
specified with the name "FILE.mpeg" is interpreted as the URL
"file:FILE.mpeg".
gopher
Gopher protocol.
hls
Read Apple HTTP Live Streaming compliant segmented stream as a uniform
one. The M3U8 playlists describing the segments can be remote HTTP
resources or local files, accessed using the standard file protocol.
The nested protocol is declared by specifying "+proto" after the hls
URI scheme name, where proto is either "file" or "http".
hls+http://host/path/to/remote/resource.m3u8
hls+file://path/to/local/resource.m3u8
Using this protocol is discouraged - the hls demuxer should work just
as well (if not, please report the issues) and is more complete. To
use the hls demuxer instead, simply use the direct URLs to the m3u8
files.
http
HTTP (Hyper Text Transfer Protocol).
This protocol accepts the following options:
chunked_post
If set to 1 use chunked Transfer-Encoding for posts, default is 1.
content_type
Set a specific content type for the POST messages.
headers
Set custom HTTP headers, can override built in default headers. The
value must be a string encoding the headers.
multiple_requests
Use persistent connections if set to 1, default is 0.
post_data
Set custom HTTP post data.
user_agent
Override the User-Agent header. If not specified a string of the
form "Lavf/<version>" will be used.
mime_type
Export the MIME type.
icy If set to 1 request ICY (SHOUTcast) metadata from the server. If
the server supports this, the metadata has to be retrieved by the
application by reading the icy_metadata_headers and
icy_metadata_packet options. The default is 1.
icy_metadata_headers
If the server supports ICY metadata, this contains the ICY-specific
HTTP reply headers, separated by newline characters.
icy_metadata_packet
If the server supports ICY metadata, and icy was set to 1, this
contains the last non-empty metadata packet sent by the server. It
should be polled in regular intervals by applications interested in
mid-stream metadata updates.
offset
Set initial byte offset.
end_offset
Try to limit the request to bytes preceding this offset.
Icecast
Icecast (stream to Icecast servers)
This protocol accepts the following options:
ice_genre
Set the stream genre.
ice_name
Set the stream name.
ice_description
Set the stream description.
ice_url
Set the stream website URL.
ice_public
Set if the stream should be public or not. The default is 0 (not
public).
user_agent
Override the User-Agent header. If not specified a string of the
form "Lavf/<version>" will be used.
password
Set the Icecast mountpoint password.
content_type
Set the stream content type. This must be set if it is different
from audio/mpeg.
legacy_icecast
This enables support for Icecast versions < 2.4.0, that do not
support the HTTP PUT method but the SOURCE method.
mmst
MMS (Microsoft Media Server) protocol over TCP.
mmsh
MMS (Microsoft Media Server) protocol over HTTP.
The required syntax is:
mmsh://<server>[:<port>][/<app>][/<playpath>]
md5
MD5 output protocol.
Computes the MD5 hash of the data to be written, and on close writes
this to the designated output or stdout if none is specified. It can be
used to test muxers without writing an actual file.
Some examples follow.
# Write the MD5 hash of the encoded AVI file to the file output.avi.md5.
avconv -i input.flv -f avi -y md5:output.avi.md5
# Write the MD5 hash of the encoded AVI file to stdout.
avconv -i input.flv -f avi -y md5:
Note that some formats (typically MOV) require the output protocol to
be seekable, so they will fail with the MD5 output protocol.
pipe
UNIX pipe access protocol.
Allow to read and write from UNIX pipes.
The accepted syntax is:
pipe:[<number>]
number is the number corresponding to the file descriptor of the pipe
(e.g. 0 for stdin, 1 for stdout, 2 for stderr). If number is not
specified, by default the stdout file descriptor will be used for
writing, stdin for reading.
For example to read from stdin with avconv:
cat test.wav | avconv -i pipe:0
# ...this is the same as...
cat test.wav | avconv -i pipe:
For writing to stdout with avconv:
avconv -i test.wav -f avi pipe:1 | cat > test.avi
# ...this is the same as...
avconv -i test.wav -f avi pipe: | cat > test.avi
Note that some formats (typically MOV), require the output protocol to
be seekable, so they will fail with the pipe output protocol.
rtmp
Real-Time Messaging Protocol.
The Real-Time Messaging Protocol (RTMP) is used for streaming
multimedia content across a TCP/IP network.
The required syntax is:
rtmp://[<username>:<password>@]<server>[:<port>][/<app>][/<instance>][/<playpath>]
The accepted parameters are:
username
An optional username (mostly for publishing).
password
An optional password (mostly for publishing).
server
The address of the RTMP server.
port
The number of the TCP port to use (by default is 1935).
app It is the name of the application to access. It usually corresponds
to the path where the application is installed on the RTMP server
(e.g. /ondemand/, /flash/live/, etc.). You can override the value
parsed from the URI through the "rtmp_app" option, too.
playpath
It is the path or name of the resource to play with reference to
the application specified in app, may be prefixed by "mp4:". You
can override the value parsed from the URI through the
"rtmp_playpath" option, too.
listen
Act as a server, listening for an incoming connection.
timeout
Maximum time to wait for the incoming connection. Implies listen.
Additionally, the following parameters can be set via command line
options (or in code via "AVOption"s):
rtmp_app
Name of application to connect on the RTMP server. This option
overrides the parameter specified in the URI.
rtmp_buffer
Set the client buffer time in milliseconds. The default is 3000.
rtmp_conn
Extra arbitrary AMF connection parameters, parsed from a string,
e.g. like "B:1 S:authMe O:1 NN:code:1.23 NS:flag:ok O:0". Each
value is prefixed by a single character denoting the type, B for
Boolean, N for number, S for string, O for object, or Z for null,
followed by a colon. For Booleans the data must be either 0 or 1
for FALSE or TRUE, respectively. Likewise for Objects the data
must be 0 or 1 to end or begin an object, respectively. Data items
in subobjects may be named, by prefixing the type with 'N' and
specifying the name before the value (i.e. "NB:myFlag:1"). This
option may be used multiple times to construct arbitrary AMF
sequences.
rtmp_flashver
Version of the Flash plugin used to run the SWF player. The default
is LNX 9,0,124,2. (When publishing, the default is FMLE/3.0
(compatible; <libavformat version>).)
rtmp_flush_interval
Number of packets flushed in the same request (RTMPT only). The
default is 10.
rtmp_live
Specify that the media is a live stream. No resuming or seeking in
live streams is possible. The default value is "any", which means
the subscriber first tries to play the live stream specified in the
playpath. If a live stream of that name is not found, it plays the
recorded stream. The other possible values are "live" and
"recorded".
rtmp_pageurl
URL of the web page in which the media was embedded. By default no
value will be sent.
rtmp_playpath
Stream identifier to play or to publish. This option overrides the
parameter specified in the URI.
rtmp_subscribe
Name of live stream to subscribe to. By default no value will be
sent. It is only sent if the option is specified or if rtmp_live
is set to live.
rtmp_swfhash
SHA256 hash of the decompressed SWF file (32 bytes).
rtmp_swfsize
Size of the decompressed SWF file, required for SWFVerification.
rtmp_swfurl
URL of the SWF player for the media. By default no value will be
sent.
rtmp_swfverify
URL to player swf file, compute hash/size automatically.
rtmp_tcurl
URL of the target stream. Defaults to proto://host[:port]/app.
For example to read with avplay a multimedia resource named "sample"
from the application "vod" from an RTMP server "myserver":
avplay rtmp://myserver/vod/sample
To publish to a password protected server, passing the playpath and app
names separately:
avconv -re -i <input> -f flv -rtmp_playpath some/long/path -rtmp_app long/app/name rtmp://username:password@myserver/
rtmpe
Encrypted Real-Time Messaging Protocol.
The Encrypted Real-Time Messaging Protocol (RTMPE) is used for
streaming multimedia content within standard cryptographic primitives,
consisting of Diffie-Hellman key exchange and HMACSHA256, generating a
pair of RC4 keys.
rtmps
Real-Time Messaging Protocol over a secure SSL connection.
The Real-Time Messaging Protocol (RTMPS) is used for streaming
multimedia content across an encrypted connection.
rtmpt
Real-Time Messaging Protocol tunneled through HTTP.
The Real-Time Messaging Protocol tunneled through HTTP (RTMPT) is used
for streaming multimedia content within HTTP requests to traverse
firewalls.
rtmpte
Encrypted Real-Time Messaging Protocol tunneled through HTTP.
The Encrypted Real-Time Messaging Protocol tunneled through HTTP
(RTMPTE) is used for streaming multimedia content within HTTP requests
to traverse firewalls.
rtmpts
Real-Time Messaging Protocol tunneled through HTTPS.
The Real-Time Messaging Protocol tunneled through HTTPS (RTMPTS) is
used for streaming multimedia content within HTTPS requests to traverse
firewalls.
librtmp rtmp, rtmpe, rtmps, rtmpt, rtmpte
Real-Time Messaging Protocol and its variants supported through
librtmp.
Requires the presence of the librtmp headers and library during
configuration. You need to explicitly configure the build with
"--enable-librtmp". If enabled this will replace the native RTMP
protocol.
This protocol provides most client functions and a few server functions
needed to support RTMP, RTMP tunneled in HTTP (RTMPT), encrypted RTMP
(RTMPE), RTMP over SSL/TLS (RTMPS) and tunneled variants of these
encrypted types (RTMPTE, RTMPTS).
The required syntax is:
<rtmp_proto>://<server>[:<port>][/<app>][/<playpath>] <options>
where rtmp_proto is one of the strings "rtmp", "rtmpt", "rtmpe",
"rtmps", "rtmpte", "rtmpts" corresponding to each RTMP variant, and
server, port, app and playpath have the same meaning as specified for
the RTMP native protocol. options contains a list of space-separated
options of the form key=val.
See the librtmp manual page (man 3 librtmp) for more information.
For example, to stream a file in real-time to an RTMP server using
avconv:
avconv -re -i myfile -f flv rtmp://myserver/live/mystream
To play the same stream using avplay:
avplay "rtmp://myserver/live/mystream live=1"
rtp
Real-Time Protocol.
rtsp
RTSP is not technically a protocol handler in libavformat, it is a
demuxer and muxer. The demuxer supports both normal RTSP (with data
transferred over RTP; this is used by e.g. Apple and Microsoft) and
Real-RTSP (with data transferred over RDT).
The muxer can be used to send a stream using RTSP ANNOUNCE to a server
supporting it (currently Darwin Streaming Server and Mischa
Spiegelmock's
RTSP server ("http://github.com/revmischa/rtsp-server")).
The required syntax for a RTSP url is:
rtsp://<hostname>[:<port>]/<path>
The following options (set on the avconv/avplay command line, or set in
code via "AVOption"s or in "avformat_open_input"), are supported:
Flags for "rtsp_transport":
udp Use UDP as lower transport protocol.
tcp Use TCP (interleaving within the RTSP control channel) as lower
transport protocol.
udp_multicast
Use UDP multicast as lower transport protocol.
http
Use HTTP tunneling as lower transport protocol, which is useful for
passing proxies.
Multiple lower transport protocols may be specified, in that case they
are tried one at a time (if the setup of one fails, the next one is
tried). For the muxer, only the "tcp" and "udp" options are supported.
Flags for "rtsp_flags":
filter_src
Accept packets only from negotiated peer address and port.
listen
Act as a server, listening for an incoming connection.
When receiving data over UDP, the demuxer tries to reorder received
packets (since they may arrive out of order, or packets may get lost
totally). This can be disabled by setting the maximum demuxing delay to
zero (via the "max_delay" field of AVFormatContext).
When watching multi-bitrate Real-RTSP streams with avplay, the streams
to display can be chosen with "-vst" n and "-ast" n for video and audio
respectively, and can be switched on the fly by pressing "v" and "a".
Example command lines:
To watch a stream over UDP, with a max reordering delay of 0.5 seconds:
avplay -max_delay 500000 -rtsp_transport udp rtsp://server/video.mp4
To watch a stream tunneled over HTTP:
avplay -rtsp_transport http rtsp://server/video.mp4
To send a stream in realtime to a RTSP server, for others to watch:
avconv -re -i <input> -f rtsp -muxdelay 0.1 rtsp://server/live.sdp
To receive a stream in realtime:
avconv -rtsp_flags listen -i rtsp://ownaddress/live.sdp <output>
sap
Session Announcement Protocol (RFC 2974). This is not technically a
protocol handler in libavformat, it is a muxer and demuxer. It is used
for signalling of RTP streams, by announcing the SDP for the streams
regularly on a separate port.
Muxer
The syntax for a SAP url given to the muxer is:
sap://<destination>[:<port>][?<options>]
The RTP packets are sent to destination on port port, or to port 5004
if no port is specified. options is a "&"-separated list. The
following options are supported:
announce_addr=address
Specify the destination IP address for sending the announcements
to. If omitted, the announcements are sent to the commonly used
SAP announcement multicast address 224.2.127.254 (sap.mcast.net),
or ff0e::2:7ffe if destination is an IPv6 address.
announce_port=port
Specify the port to send the announcements on, defaults to 9875 if
not specified.
ttl=ttl
Specify the time to live value for the announcements and RTP
packets, defaults to 255.
same_port=0|1
If set to 1, send all RTP streams on the same port pair. If zero
(the default), all streams are sent on unique ports, with each
stream on a port 2 numbers higher than the previous. VLC/Live555
requires this to be set to 1, to be able to receive the stream.
The RTP stack in libavformat for receiving requires all streams to
be sent on unique ports.
Example command lines follow.
To broadcast a stream on the local subnet, for watching in VLC:
avconv -re -i <input> -f sap sap://224.0.0.255?same_port=1
Similarly, for watching in avplay:
avconv -re -i <input> -f sap sap://224.0.0.255
And for watching in avplay, over IPv6:
avconv -re -i <input> -f sap sap://[ff0e::1:2:3:4]
Demuxer
The syntax for a SAP url given to the demuxer is:
sap://[<address>][:<port>]
address is the multicast address to listen for announcements on, if
omitted, the default 224.2.127.254 (sap.mcast.net) is used. port is the
port that is listened on, 9875 if omitted.
The demuxers listens for announcements on the given address and port.
Once an announcement is received, it tries to receive that particular
stream.
Example command lines follow.
To play back the first stream announced on the normal SAP multicast
address:
avplay sap://
To play back the first stream announced on one the default IPv6 SAP
multicast address:
avplay sap://[ff0e::2:7ffe]
tcp
Trasmission Control Protocol.
The required syntax for a TCP url is:
tcp://<hostname>:<port>[?<options>]
listen
Listen for an incoming connection
avconv -i <input> -f <format> tcp://<hostname>:<port>?listen
avplay tcp://<hostname>:<port>
tls
Transport Layer Security (TLS) / Secure Sockets Layer (SSL)
The required syntax for a TLS url is:
tls://<hostname>:<port>
The following parameters can be set via command line options (or in
code via "AVOption"s):
ca_file
A file containing certificate authority (CA) root certificates to
treat as trusted. If the linked TLS library contains a default this
might not need to be specified for verification to work, but not
all libraries and setups have defaults built in.
tls_verify=1|0
If enabled, try to verify the peer that we are communicating with.
Note, if using OpenSSL, this currently only makes sure that the
peer certificate is signed by one of the root certificates in the
CA database, but it does not validate that the certificate actually
matches the host name we are trying to connect to. (With GnuTLS,
the host name is validated as well.)
This is disabled by default since it requires a CA database to be
provided by the caller in many cases.
cert_file
A file containing a certificate to use in the handshake with the
peer. (When operating as server, in listen mode, this is more
often required by the peer, while client certificates only are
mandated in certain setups.)
key_file
A file containing the private key for the certificate.
listen=1|0
If enabled, listen for connections on the provided port, and assume
the server role in the handshake instead of the client role.
udp
User Datagram Protocol.
The required syntax for a UDP url is:
udp://<hostname>:<port>[?<options>]
options contains a list of &-separated options of the form key=val.
Follow the list of supported options.
buffer_size=size
set the UDP buffer size in bytes
localport=port
override the local UDP port to bind with
localaddr=addr
Choose the local IP address. This is useful e.g. if sending
multicast and the host has multiple interfaces, where the user can
choose which interface to send on by specifying the IP address of
that interface.
pkt_size=size
set the size in bytes of UDP packets
reuse=1|0
explicitly allow or disallow reusing UDP sockets
ttl=ttl
set the time to live value (for multicast only)
connect=1|0
Initialize the UDP socket with "connect()". In this case, the
destination address can't be changed with ff_udp_set_remote_url
later. If the destination address isn't known at the start, this
option can be specified in ff_udp_set_remote_url, too. This allows
finding out the source address for the packets with getsockname,
and makes writes return with AVERROR(ECONNREFUSED) if "destination
unreachable" is received. For receiving, this gives the benefit of
only receiving packets from the specified peer address/port.
sources=address[,address]
Only receive packets sent to the multicast group from one of the
specified sender IP addresses.
block=address[,address]
Ignore packets sent to the multicast group from the specified
sender IP addresses.
Some usage examples of the udp protocol with avconv follow.
To stream over UDP to a remote endpoint:
avconv -i <input> -f <format> udp://<hostname>:<port>
To stream in mpegts format over UDP using 188 sized UDP packets, using
a large input buffer:
avconv -i <input> -f mpegts udp://<hostname>:<port>?pkt_size=188&buffer_size=65535
To receive over UDP from a remote endpoint:
avconv -i udp://[<multicast-address>]:<port>
unix
Unix local socket
The required syntax for a Unix socket URL is:
unix://<filepath>
The following parameters can be set via command line options (or in
code via "AVOption"s):
timeout
Timeout in ms.
listen
Create the Unix socket in listening mode.
When you configure your Libav build, all the supported bitstream
filters are enabled by default. You can list all available ones using
the configure option "--list-bsfs".
You can disable all the bitstream filters using the configure option
"--disable-bsfs", and selectively enable any bitstream filter using the
option "--enable-bsf=BSF", or you can disable a particular bitstream
filter using the option "--disable-bsf=BSF".
The option "-bsfs" of the av* tools will display the list of all the
supported bitstream filters included in your build.
Below is a description of the currently available bitstream filters.
aac_adtstoasc
chomp
dump_extradata
h264_mp4toannexb
imx_dump_header
mjpeg2jpeg
Convert MJPEG/AVI1 packets to full JPEG/JFIF packets.
MJPEG is a video codec wherein each video frame is essentially a JPEG
image. The individual frames can be extracted without loss, e.g. by
avconv -i ../some_mjpeg.avi -c:v copy frames_%d.jpg
Unfortunately, these chunks are incomplete JPEG images, because they
lack the DHT segment required for decoding. Quoting from
<http://www.digitalpreservation.gov/formats/fdd/fdd000063.shtml>:
Avery Lee, writing in the rec.video.desktop newsgroup in 2001,
commented that "MJPEG, or at least the MJPEG in AVIs having the MJPG
fourcc, is restricted JPEG with a fixed -- and *omitted* -- Huffman
table. The JPEG must be YCbCr colorspace, it must be 4:2:2, and it must
use basic Huffman encoding, not arithmetic or progressive. . . . You
can indeed extract the MJPEG frames and decode them with a regular JPEG
decoder, but you have to prepend the DHT segment to them, or else the
decoder won't have any idea how to decompress the data. The exact table
necessary is given in the OpenDML spec."
This bitstream filter patches the header of frames extracted from an
MJPEG stream (carrying the AVI1 header ID and lacking a DHT segment) to
produce fully qualified JPEG images.
avconv -i mjpeg-movie.avi -c:v copy -bsf:v mjpeg2jpeg frame_%d.jpg
exiftran -i -9 frame*.jpg
avconv -i frame_%d.jpg -c:v copy rotated.avi
mjpega_dump_header
movsub
mp3_header_compress
mp3_header_decompress
noise
remove_extradata
A filtergraph is a directed graph of connected filters. It can contain
cycles, and there can be multiple links between a pair of filters. Each
link has one input pad on one side connecting it to one filter from
which it takes its input, and one output pad on the other side
connecting it to one filter accepting its output.
Each filter in a filtergraph is an instance of a filter class
registered in the application, which defines the features and the
number of input and output pads of the filter.
A filter with no input pads is called a "source", and a filter with no
output pads is called a "sink".
Filtergraph syntax
A filtergraph has a textual representation, which is recognized by the
-filter/-vf and -filter_complex options in avconv and -vf in avplay,
and by the "avfilter_graph_parse()"/"avfilter_graph_parse2()" functions
defined in libavfilter/avfilter.h.
A filterchain consists of a sequence of connected filters, each one
connected to the previous one in the sequence. A filterchain is
represented by a list of ","-separated filter descriptions.
A filtergraph consists of a sequence of filterchains. A sequence of
filterchains is represented by a list of ";"-separated filterchain
descriptions.
A filter is represented by a string of the form:
[in_link_1]...[in_link_N]filter_name=arguments[out_link_1]...[out_link_M]
filter_name is the name of the filter class of which the described
filter is an instance of, and has to be the name of one of the filter
classes registered in the program. The name of the filter class is
optionally followed by a string "=arguments".
arguments is a string which contains the parameters used to initialize
the filter instance. It may have one of two forms:
o A ':'-separated list of key=value pairs.
o A ':'-separated list of value. In this case, the keys are assumed
to be the option names in the order they are declared. E.g. the
"fade" filter declares three options in this order -- type,
start_frame and nb_frames. Then the parameter list in:0:30 means
that the value in is assigned to the option type, 0 to start_frame
and 30 to nb_frames.
If the option value itself is a list of items (e.g. the "format" filter
takes a list of pixel formats), the items in the list are usually
separated by '|'.
The list of arguments can be quoted using the character "'" as initial
and ending mark, and the character '\' for escaping the characters
within the quoted text; otherwise the argument string is considered
terminated when the next special character (belonging to the set
"[]=;,") is encountered.
The name and arguments of the filter are optionally preceded and
followed by a list of link labels. A link label allows to name a link
and associate it to a filter output or input pad. The preceding labels
in_link_1 ... in_link_N, are associated to the filter input pads, the
following labels out_link_1 ... out_link_M, are associated to the
output pads.
When two link labels with the same name are found in the filtergraph, a
link between the corresponding input and output pad is created.
If an output pad is not labelled, it is linked by default to the first
unlabelled input pad of the next filter in the filterchain. For
example in the filterchain
nullsrc, split[L1], [L2]overlay, nullsink
the split filter instance has two output pads, and the overlay filter
instance two input pads. The first output pad of split is labelled
"L1", the first input pad of overlay is labelled "L2", and the second
output pad of split is linked to the second input pad of overlay, which
are both unlabelled.
In a complete filterchain all the unlabelled filter input and output
pads must be connected. A filtergraph is considered valid if all the
filter input and output pads of all the filterchains are connected.
Libavfilter will automatically insert scale filters where format
conversion is required. It is possible to specify swscale flags for
those automatically inserted scalers by prepending "sws_flags=flags;"
to the filtergraph description.
Here is a BNF description of the filtergraph syntax:
<NAME> ::= sequence of alphanumeric characters and '_'
<LINKLABEL> ::= "[" <NAME> "]"
<LINKLABELS> ::= <LINKLABEL> [<LINKLABELS>]
<FILTER_ARGUMENTS> ::= sequence of chars (possibly quoted)
<FILTER> ::= [<LINKLABELS>] <NAME> ["=" <FILTER_ARGUMENTS>] [<LINKLABELS>]
<FILTERCHAIN> ::= <FILTER> [,<FILTERCHAIN>]
<FILTERGRAPH> ::= [sws_flags=<flags>;] <FILTERCHAIN> [;<FILTERGRAPH>]
When you configure your Libav build, you can disable any of the
existing filters using --disable-filters. The configure output will
show the audio filters included in your build.
Below is a description of the currently available audio filters.
aformat
Convert the input audio to one of the specified formats. The framework
will negotiate the most appropriate format to minimize conversions.
It accepts the following parameters:
sample_fmts
A '|'-separated list of requested sample formats.
sample_rates
A '|'-separated list of requested sample rates.
channel_layouts
A '|'-separated list of requested channel layouts.
If a parameter is omitted, all values are allowed.
Force the output to either unsigned 8-bit or signed 16-bit stereo
aformat=sample_fmts=u8|s16:channel_layouts=stereo
amix
Mixes multiple audio inputs into a single output.
For example
avconv -i INPUT1 -i INPUT2 -i INPUT3 -filter_complex amix=inputs=3:duration=first:dropout_transition=3 OUTPUT
will mix 3 input audio streams to a single output with the same
duration as the first input and a dropout transition time of 3 seconds.
It accepts the following parameters:
inputs
The number of inputs. If unspecified, it defaults to 2.
duration
How to determine the end-of-stream.
longest
The duration of the longest input. (default)
shortest
The duration of the shortest input.
first
The duration of the first input.
dropout_transition
The transition time, in seconds, for volume renormalization when an
input stream ends. The default value is 2 seconds.
anull
Pass the audio source unchanged to the output.
asetpts
Change the PTS (presentation timestamp) of the input audio frames.
It accepts the following parameters:
expr
The expression which is evaluated for each frame to construct its
timestamp.
The expression is evaluated through the eval API and can contain the
following constants:
PTS the presentation timestamp in input
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
N The number of audio samples passed through the filter so far,
starting at 0.
S The number of audio samples in the current frame.
SR The audio sample rate.
STARTPTS
The PTS of the first frame.
PREV_INPTS
The previous input PTS.
PREV_OUTPTS
The previous output PTS.
RTCTIME
The wallclock (RTC) time in microseconds.
RTCSTART
The wallclock (RTC) time at the start of the movie in microseconds.
Some examples:
# Start counting PTS from zero
asetpts=expr=PTS-STARTPTS
# Generate timestamps by counting samples
asetpts=expr=N/SR/TB
# Generate timestamps from a "live source" and rebase onto the current timebase
asetpts='(RTCTIME - RTCSTART) / (TB * 1000000)"
asettb
Set the timebase to use for the output frames timestamps. It is mainly
useful for testing timebase configuration.
This filter accepts the following parameters:
expr
The expression which is evaluated into the output timebase.
The expression can contain the constants PI, E, PHI, AVTB (the default
timebase), intb (the input timebase), and sr (the sample rate, audio
only).
The default value for the input is intb.
Some examples:
# Set the timebase to 1/25:
settb=1/25
# Set the timebase to 1/10:
settb=0.1
# Set the timebase to 1001/1000:
settb=1+0.001
# Set the timebase to 2*intb:
settb=2*intb
# Set the default timebase value:
settb=AVTB
# Set the timebase to twice the sample rate:
asettb=sr*2
ashowinfo
Show a line containing various information for each input audio frame.
The input audio is not modified.
The shown line contains a sequence of key/value pairs of the form
key:value.
It accepts the following parameters:
n The (sequential) number of the input frame, starting from 0.
pts The presentation timestamp of the input frame, in time base units;
the time base depends on the filter input pad, and is usually
1/sample_rate.
pts_time
The presentation timestamp of the input frame in seconds.
fmt The sample format.
chlayout
The channel layout.
rate
The sample rate for the audio frame.
nb_samples
The number of samples (per channel) in the frame.
checksum
The Adler-32 checksum (printed in hexadecimal) of the audio data.
For planar audio, the data is treated as if all the planes were
concatenated.
plane_checksums
A list of Adler-32 checksums for each data plane.
asplit
Split input audio into several identical outputs.
It accepts a single parameter, which specifies the number of outputs.
If unspecified, it defaults to 2.
For example,
avconv -i INPUT -filter_complex asplit=5 OUTPUT
will create 5 copies of the input audio.
asyncts
Synchronize audio data with timestamps by squeezing/stretching it
and/or dropping samples/adding silence when needed.
It accepts the following parameters:
compensate
Enable stretching/squeezing the data to make it match the
timestamps. Disabled by default. When disabled, time gaps are
covered with silence.
min_delta
The minimum difference between timestamps and audio data (in
seconds) to trigger adding/dropping samples. The default value is
0.1. If you get an imperfect sync with this filter, try setting
this parameter to 0.
max_comp
The maximum compensation in samples per second. Only relevant with
compensate=1. The default value is 500.
first_pts
Assume that the first PTS should be this value. The time base is 1
/ sample rate. This allows for padding/trimming at the start of the
stream. By default, no assumption is made about the first frame's
expected PTS, so no padding or trimming is done. For example, this
could be set to 0 to pad the beginning with silence if an audio
stream starts after the video stream or to trim any samples with a
negative PTS due to encoder delay.
atrim
Trim the input so that the output contains one continuous subpart of
the input.
It accepts the following parameters:
start
Timestamp (in seconds) of the start of the section to keep. I.e.
the audio sample with the timestamp start will be the first sample
in the output.
end Timestamp (in seconds) of the first audio sample that will be
dropped. I.e. the audio sample immediately preceding the one with
the timestamp end will be the last sample in the output.
start_pts
Same as start, except this option sets the start timestamp in
samples instead of seconds.
end_pts
Same as end, except this option sets the end timestamp in samples
instead of seconds.
duration
The maximum duration of the output in seconds.
start_sample
The number of the first sample that should be output.
end_sample
The number of the first sample that should be dropped.
Note that the first two sets of the start/end options and the duration
option look at the frame timestamp, while the _sample options simply
count the samples that pass through the filter. So start/end_pts and
start/end_sample will give different results when the timestamps are
wrong, inexact or do not start at zero. Also note that this filter does
not modify the timestamps. If you wish to have the output timestamps
start at zero, insert the asetpts filter after the atrim filter.
If multiple start or end options are set, this filter tries to be
greedy and keep all samples that match at least one of the specified
constraints. To keep only the part that matches all the constraints at
once, chain multiple atrim filters.
The defaults are such that all the input is kept. So it is possible to
set e.g. just the end values to keep everything before the specified
time.
Examples:
o Drop everything except the second minute of input:
avconv -i INPUT -af atrim=60:120
o Keep only the first 1000 samples:
avconv -i INPUT -af atrim=end_sample=1000
bs2b
Bauer stereo to binaural transformation, which improves headphone
listening of stereo audio records.
It accepts the following parameters:
profile
Pre-defined crossfeed level.
default
Default level (fcut=700, feed=50).
cmoy
Chu Moy circuit (fcut=700, feed=60).
jmeier
Jan Meier circuit (fcut=650, feed=95).
fcut
Cut frequency (in Hz).
feed
Feed level (in Hz).
channelsplit
Split each channel from an input audio stream into a separate output
stream.
It accepts the following parameters:
channel_layout
The channel layout of the input stream. The default is "stereo".
For example, assuming a stereo input MP3 file,
avconv -i in.mp3 -filter_complex channelsplit out.mkv
will create an output Matroska file with two audio streams, one
containing only the left channel and the other the right channel.
Split a 5.1 WAV file into per-channel files:
avconv -i in.wav -filter_complex
'channelsplit=channel_layout=5.1[FL][FR][FC][LFE][SL][SR]'
-map '[FL]' front_left.wav -map '[FR]' front_right.wav -map '[FC]'
front_center.wav -map '[LFE]' lfe.wav -map '[SL]' side_left.wav -map '[SR]'
side_right.wav
channelmap
Remap input channels to new locations.
It accepts the following parameters:
channel_layout
The channel layout of the output stream.
map Map channels from input to output. The argument is a '|'-separated
list of mappings, each in the "in_channel-out_channel" or
in_channel form. in_channel can be either the name of the input
channel (e.g. FL for front left) or its index in the input channel
layout. out_channel is the name of the output channel or its index
in the output channel layout. If out_channel is not given then it
is implicitly an index, starting with zero and increasing by one
for each mapping.
If no mapping is present, the filter will implicitly map input channels
to output channels, preserving indices.
For example, assuming a 5.1+downmix input MOV file,
avconv -i in.mov -filter 'channelmap=map=DL-FL|DR-FR' out.wav
will create an output WAV file tagged as stereo from the downmix
channels of the input.
To fix a 5.1 WAV improperly encoded in AAC's native channel order
avconv -i in.wav -filter 'channelmap=1|2|0|5|3|4:channel_layout=5.1' out.wav
compand
Compress or expand the audio's dynamic range.
It accepts the following parameters:
attacks
decays
A list of times in seconds for each channel over which the
instantaneous level of the input signal is averaged to determine
its volume. attacks refers to increase of volume and decays refers
to decrease of volume. For most situations, the attack time
(response to the audio getting louder) should be shorter than the
decay time, because the human ear is more sensitive to sudden loud
audio than sudden soft audio. A typical value for attack is 0.3
seconds and a typical value for decay is 0.8 seconds.
points
A list of points for the transfer function, specified in dB
relative to the maximum possible signal amplitude. Each key points
list must be defined using the following syntax:
"x0/y0|x1/y1|x2/y2|...."
The input values must be in strictly increasing order but the
transfer function does not have to be monotonically rising. The
point "0/0" is assumed but may be overridden (by "0/out-dBn").
Typical values for the transfer function are "-70/-70|-60/-20".
soft-knee
Set the curve radius in dB for all joints. It defaults to 0.01.
gain
Set the additional gain in dB to be applied at all points on the
transfer function. This allows for easy adjustment of the overall
gain. It defaults to 0.
volume
Set an initial volume, in dB, to be assumed for each channel when
filtering starts. This permits the user to supply a nominal level
initially, so that, for example, a very large gain is not applied
to initial signal levels before the companding has begun to
operate. A typical value for audio which is initially quiet is -90
dB. It defaults to 0.
delay
Set a delay, in seconds. The input audio is analyzed immediately,
but audio is delayed before being fed to the volume adjuster.
Specifying a delay approximately equal to the attack/decay times
allows the filter to effectively operate in predictive rather than
reactive mode. It defaults to 0.
Examples
o Make music with both quiet and loud passages suitable for listening
to in a noisy environment:
compand=.3|.3:1|1:-90/-60|-60/-40|-40/-30|-20/-20:6:0:-90:0.2
o A noise gate for when the noise is at a lower level than the
signal:
compand=.1|.1:.2|.2:-900/-900|-50.1/-900|-50/-50:.01:0:-90:.1
o Here is another noise gate, this time for when the noise is at a
higher level than the signal (making it, in some ways, similar to
squelch):
compand=.1|.1:.1|.1:-45.1/-45.1|-45/-900|0/-900:.01:45:-90:.1
join
Join multiple input streams into one multi-channel stream.
It accepts the following parameters:
inputs
The number of input streams. It defaults to 2.
channel_layout
The desired output channel layout. It defaults to stereo.
map Map channels from inputs to output. The argument is a '|'-separated
list of mappings, each in the "input_idx.in_channel-out_channel"
form. input_idx is the 0-based index of the input stream.
in_channel can be either the name of the input channel (e.g. FL for
front left) or its index in the specified input stream. out_channel
is the name of the output channel.
The filter will attempt to guess the mappings when they are not
specified explicitly. It does so by first trying to find an unused
matching input channel and if that fails it picks the first unused
input channel.
Join 3 inputs (with properly set channel layouts):
avconv -i INPUT1 -i INPUT2 -i INPUT3 -filter_complex join=inputs=3 OUTPUT
Build a 5.1 output from 6 single-channel streams:
avconv -i fl -i fr -i fc -i sl -i sr -i lfe -filter_complex
'join=inputs=6:channel_layout=5.1:map=0.0-FL|1.0-FR|2.0-FC|3.0-SL|4.0-SR|5.0-LFE'
out
resample
Convert the audio sample format, sample rate and channel layout. It is
not meant to be used directly; it is inserted automatically by
libavfilter whenever conversion is needed. Use the aformat filter to
force a specific conversion.
volume
Adjust the input audio volume.
It accepts the following parameters:
volume
This expresses how the audio volume will be increased or decreased.
Output values are clipped to the maximum value.
The output audio volume is given by the relation:
<output_volume> = <volume> * <input_volume>
The default value for volume is 1.0.
precision
This parameter represents the mathematical precision.
It determines which input sample formats will be allowed, which
affects the precision of the volume scaling.
fixed
8-bit fixed-point; this limits input sample format to U8, S16,
and S32.
float
32-bit floating-point; this limits input sample format to FLT.
(default)
double
64-bit floating-point; this limits input sample format to DBL.
replaygain
Choose the behaviour on encountering ReplayGain side data in input
frames.
drop
Remove ReplayGain side data, ignoring its contents (the
default).
ignore
Ignore ReplayGain side data, but leave it in the frame.
track
Prefer the track gain, if present.
album
Prefer the album gain, if present.
replaygain_preamp
Pre-amplification gain in dB to apply to the selected replaygain
gain.
Default value for replaygain_preamp is 0.0.
replaygain_noclip
Prevent clipping by limiting the gain applied.
Default value for replaygain_noclip is 1.
Examples
o Halve the input audio volume:
volume=volume=0.5
volume=volume=1/2
volume=volume=-6.0206dB
o Increase input audio power by 6 decibels using fixed-point
precision:
volume=volume=6dB:precision=fixed
Below is a description of the currently available audio sources.
anullsrc
The null audio source; it never returns audio frames. It is mainly
useful as a template and for use in analysis / debugging tools.
It accepts, as an optional parameter, a string of the form
sample_rate:channel_layout.
sample_rate specifies the sample rate, and defaults to 44100.
channel_layout specifies the channel layout, and can be either an
integer or a string representing a channel layout. The default value of
channel_layout is 3, which corresponds to CH_LAYOUT_STEREO.
Check the channel_layout_map definition in libavutil/channel_layout.c
for the mapping between strings and channel layout values.
Some examples:
# Set the sample rate to 48000 Hz and the channel layout to CH_LAYOUT_MONO
anullsrc=48000:4
# The same as above
anullsrc=48000:mono
abuffer
Buffer audio frames, and make them available to the filter chain.
This source is not intended to be part of user-supplied graph
descriptions; it is for insertion by calling programs, through the
interface defined in libavfilter/buffersrc.h.
It accepts the following parameters:
time_base
The timebase which will be used for timestamps of submitted frames.
It must be either a floating-point number or in
numerator/denominator form.
sample_rate
The audio sample rate.
sample_fmt
The name of the sample format, as returned by
"av_get_sample_fmt_name()".
channel_layout
The channel layout of the audio data, in the form that can be
accepted by "av_get_channel_layout()".
All the parameters need to be explicitly defined.
Below is a description of the currently available audio sinks.
anullsink
Null audio sink; do absolutely nothing with the input audio. It is
mainly useful as a template and for use in analysis / debugging tools.
abuffersink
This sink is intended for programmatic use. Frames that arrive on this
sink can be retrieved by the calling program, using the interface
defined in libavfilter/buffersink.h.
It does not accept any parameters.
When you configure your Libav build, you can disable any of the
existing filters using --disable-filters. The configure output will
show the video filters included in your build.
Below is a description of the currently available video filters.
blackframe
Detect frames that are (almost) completely black. Can be useful to
detect chapter transitions or commercials. Output lines consist of the
frame number of the detected frame, the percentage of blackness, the
position in the file if known or -1 and the timestamp in seconds.
In order to display the output lines, you need to set the loglevel at
least to the AV_LOG_INFO value.
It accepts the following parameters:
amount
The percentage of the pixels that have to be below the threshold;
it defaults to 98.
threshold
The threshold below which a pixel value is considered black; it
defaults to 32.
boxblur
Apply a boxblur algorithm to the input video.
It accepts the following parameters:
luma_radius
luma_power
chroma_radius
chroma_power
alpha_radius
alpha_power
The chroma and alpha parameters are optional. If not specified, they
default to the corresponding values set for luma_radius and luma_power.
luma_radius, chroma_radius, and alpha_radius represent the radius in
pixels of the box used for blurring the corresponding input plane. They
are expressions, and can contain the following constants:
w, h
The input width and height in pixels.
cw, ch
The input chroma image width and height in pixels.
hsub, vsub
The horizontal and vertical chroma subsample values. For example,
for the pixel format "yuv422p", hsub is 2 and vsub is 1.
The radius must be a non-negative number, and must not be greater than
the value of the expression "min(w,h)/2" for the luma and alpha planes,
and of "min(cw,ch)/2" for the chroma planes.
luma_power, chroma_power, and alpha_power represent how many times the
boxblur filter is applied to the corresponding plane.
Some examples:
o Apply a boxblur filter with the luma, chroma, and alpha radii set
to 2:
boxblur=luma_radius=2:luma_power=1
o Set the luma radius to 2, and alpha and chroma radius to 0:
boxblur=2:1:0:0:0:0
o Set the luma and chroma radii to a fraction of the video dimension:
boxblur=luma_radius=min(h,w)/10:luma_power=1:chroma_radius=min(cw,ch)/10:chroma_power=1
copy
Copy the input source unchanged to the output. This is mainly useful
for testing purposes.
crop
Crop the input video to given dimensions.
It accepts the following parameters:
out_w
The width of the output video.
out_h
The height of the output video.
x The horizontal position, in the input video, of the left edge of
the output video.
y The vertical position, in the input video, of the top edge of the
output video.
The parameters are expressions containing the following constants:
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
x, y
The computed values for x and y. They are evaluated for each new
frame.
in_w, in_h
The input width and height.
iw, ih
These are the same as in_w and in_h.
out_w, out_h
The output (cropped) width and height.
ow, oh
These are the same as out_w and out_h.
n The number of the input frame, starting from 0.
t The timestamp expressed in seconds. It's NAN if the input timestamp
is unknown.
The out_w and out_h parameters specify the expressions for the width
and height of the output (cropped) video. They are only evaluated
during the configuration of the filter.
The default value of out_w is "in_w", and the default value of out_h is
"in_h".
The expression for out_w may depend on the value of out_h, and the
expression for out_h may depend on out_w, but they cannot depend on x
and y, as x and y are evaluated after out_w and out_h.
The x and y parameters specify the expressions for the position of the
top-left corner of the output (non-cropped) area. They are evaluated
for each frame. If the evaluated value is not valid, it is approximated
to the nearest valid value.
The default value of x is "(in_w-out_w)/2", and the default value for y
is "(in_h-out_h)/2", which set the cropped area at the center of the
input image.
The expression for x may depend on y, and the expression for y may
depend on x.
Some examples:
# Crop the central input area with size 100x100
crop=out_w=100:out_h=100
# Crop the central input area with size 2/3 of the input video
"crop=out_w=2/3*in_w:out_h=2/3*in_h"
# Crop the input video central square
crop=out_w=in_h
# Delimit the rectangle with the top-left corner placed at position
# 100:100 and the right-bottom corner corresponding to the right-bottom
# corner of the input image
crop=out_w=in_w-100:out_h=in_h-100:x=100:y=100
# Crop 10 pixels from the left and right borders, and 20 pixels from
# the top and bottom borders
"crop=out_w=in_w-2*10:out_h=in_h-2*20"
# Keep only the bottom right quarter of the input image
"crop=out_w=in_w/2:out_h=in_h/2:x=in_w/2:y=in_h/2"
# Crop height for getting Greek harmony
"crop=out_w=in_w:out_h=1/PHI*in_w"
# Trembling effect
"crop=in_w/2:in_h/2:(in_w-out_w)/2+((in_w-out_w)/2)*sin(n/10):(in_h-out_h)/2 +((in_h-out_h)/2)*sin(n/7)"
# Erratic camera effect depending on timestamp
"crop=out_w=in_w/2:out_h=in_h/2:x=(in_w-out_w)/2+((in_w-out_w)/2)*sin(t*10):y=(in_h-out_h)/2 +((in_h-out_h)/2)*sin(t*13)"
# Set x depending on the value of y
"crop=in_w/2:in_h/2:y:10+10*sin(n/10)"
cropdetect
Auto-detect the crop size.
It calculates the necessary cropping parameters and prints the
recommended parameters via the logging system. The detected dimensions
correspond to the non-black area of the input video.
It accepts the following parameters:
limit
The threshold, an optional parameter between nothing (0) and
everything (255). It defaults to 24.
round
The value which the width/height should be divisible by. It
defaults to 16. The offset is automatically adjusted to center the
video. Use 2 to get only even dimensions (needed for 4:2:2 video).
16 is best when encoding to most video codecs.
reset
A counter that determines how many frames cropdetect will reset the
previously detected largest video area after. It will then start
over and detect the current optimal crop area. It defaults to 0.
This can be useful when channel logos distort the video area. 0
indicates 'never reset', and returns the largest area encountered
during playback.
delogo
Suppress a TV station logo by a simple interpolation of the surrounding
pixels. Just set a rectangle covering the logo and watch it disappear
(and sometimes something even uglier appear - your mileage may vary).
It accepts the following parameters:
x, y
Specify the top left corner coordinates of the logo. They must be
specified.
w, h
Specify the width and height of the logo to clear. They must be
specified.
band, t
Specify the thickness of the fuzzy edge of the rectangle (added to
w and h). The default value is 4.
show
When set to 1, a green rectangle is drawn on the screen to simplify
finding the right x, y, w, h parameters, and band is set to 4. The
default value is 0.
An example:
o Set a rectangle covering the area with top left corner coordinates
0,0 and size 100x77, and a band of size 10:
delogo=x=0:y=0:w=100:h=77:band=10
drawbox
Draw a colored box on the input image.
It accepts the following parameters:
x, y
Specify the top left corner coordinates of the box. It defaults to
0.
width, height
Specify the width and height of the box; if 0 they are interpreted
as the input width and height. It defaults to 0.
color
Specify the color of the box to write. It can be the name of a
color (case insensitive match) or a 0xRRGGBB[AA] sequence.
Some examples:
# Draw a black box around the edge of the input image
drawbox
# Draw a box with color red and an opacity of 50%
drawbox=x=10:y=20:width=200:height=60:color=red@0.5"
drawtext
Draw a text string or text from a specified file on top of a video,
using the libfreetype library.
To enable compilation of this filter, you need to configure Libav with
"--enable-libfreetype". To enable default font fallback and the font
option you need to configure Libav with "--enable-libfontconfig".
The filter also recognizes strftime() sequences in the provided text
and expands them accordingly. Check the documentation of strftime().
It accepts the following parameters:
font
The font family to be used for drawing text. By default Sans.
fontfile
The font file to be used for drawing text. The path must be
included. This parameter is mandatory if the fontconfig support is
disabled.
text
The text string to be drawn. The text must be a sequence of UTF-8
encoded characters. This parameter is mandatory if no file is
specified with the parameter textfile.
textfile
A text file containing text to be drawn. The text must be a
sequence of UTF-8 encoded characters.
This parameter is mandatory if no text string is specified with the
parameter text.
If both text and textfile are specified, an error is thrown.
x, y
The offsets where text will be drawn within the video frame. It is
relative to the top/left border of the output image. They accept
expressions similar to the overlay filter:
x, y
The computed values for x and y. They are evaluated for each
new frame.
main_w, main_h
The main input width and height.
W, H
These are the same as main_w and main_h.
text_w, text_h
The rendered text's width and height.
w, h
These are the same as text_w and text_h.
n The number of frames processed, starting from 0.
t The timestamp, expressed in seconds. It's NAN if the input
timestamp is unknown.
The default value of x and y is 0.
fontsize
The font size to be used for drawing text. The default value of
fontsize is 16.
fontcolor
The color to be used for drawing fonts. It is either a string
(e.g. "red"), or in 0xRRGGBB[AA] format (e.g. "0xff000033"),
possibly followed by an alpha specifier. The default value of
fontcolor is "black".
boxcolor
The color to be used for drawing box around text. It is either a
string (e.g. "yellow") or in 0xRRGGBB[AA] format (e.g. "0xff00ff"),
possibly followed by an alpha specifier. The default value of
boxcolor is "white".
box Used to draw a box around text using the background color. The
value must be either 1 (enable) or 0 (disable). The default value
of box is 0.
shadowx, shadowy
The x and y offsets for the text shadow position with respect to
the position of the text. They can be either positive or negative
values. The default value for both is "0".
shadowcolor
The color to be used for drawing a shadow behind the drawn text.
It can be a color name (e.g. "yellow") or a string in the
0xRRGGBB[AA] form (e.g. "0xff00ff"), possibly followed by an alpha
specifier. The default value of shadowcolor is "black".
ft_load_flags
The flags to be used for loading the fonts.
The flags map the corresponding flags supported by libfreetype, and
are a combination of the following values:
default
no_scale
no_hinting
render
no_bitmap
vertical_layout
force_autohint
crop_bitmap
pedantic
ignore_global_advance_width
no_recurse
ignore_transform
monochrome
linear_design
no_autohint
end table
Default value is "render".
For more information consult the documentation for the FT_LOAD_*
libfreetype flags.
tabsize
The size in number of spaces to use for rendering the tab. Default
value is 4.
fix_bounds
If true, check and fix text coords to avoid clipping.
For example the command:
drawtext="fontfile=/usr/share/fonts/truetype/freefont/FreeSerif.ttf: text='Test Text'"
will draw "Test Text" with font FreeSerif, using the default values for
the optional parameters.
The command:
drawtext="fontfile=/usr/share/fonts/truetype/freefont/FreeSerif.ttf: text='Test Text':\
x=100: y=50: fontsize=24: fontcolor=yellow@0.2: box=1: boxcolor=red@0.2"
will draw 'Test Text' with font FreeSerif of size 24 at position x=100
and y=50 (counting from the top-left corner of the screen), text is
yellow with a red box around it. Both the text and the box have an
opacity of 20%.
Note that the double quotes are not necessary if spaces are not used
within the parameter list.
For more information about libfreetype, check:
<http://www.freetype.org/>.
fade
Apply a fade-in/out effect to the input video.
It accepts the following parameters:
type
The effect type can be either "in" for a fade-in, or "out" for a
fade-out effect.
start_frame
The number of the frame to start applying the fade effect at.
nb_frames
The number of frames that the fade effect lasts. At the end of the
fade-in effect, the output video will have the same intensity as
the input video. At the end of the fade-out transition, the output
video will be completely black.
Some examples:
# Fade in the first 30 frames of video
fade=type=in:nb_frames=30
# Fade out the last 45 frames of a 200-frame video
fade=type=out:start_frame=155:nb_frames=45
# Fade in the first 25 frames and fade out the last 25 frames of a 1000-frame video
fade=type=in:start_frame=0:nb_frames=25, fade=type=out:start_frame=975:nb_frames=25
# Make the first 5 frames black, then fade in from frame 5-24
fade=type=in:start_frame=5:nb_frames=20
fieldorder
Transform the field order of the input video.
It accepts the following parameters:
order
The output field order. Valid values are tff for top field first or
bff for bottom field first.
The default value is "tff".
The transformation is done by shifting the picture content up or down
by one line, and filling the remaining line with appropriate picture
content. This method is consistent with most broadcast field order
converters.
If the input video is not flagged as being interlaced, or it is already
flagged as being of the required output field order, then this filter
does not alter the incoming video.
It is very useful when converting to or from PAL DV material, which is
bottom field first.
For example:
./avconv -i in.vob -vf "fieldorder=order=bff" out.dv
fifo
Buffer input images and send them when they are requested.
It is mainly useful when auto-inserted by the libavfilter framework.
It does not take parameters.
format
Convert the input video to one of the specified pixel formats.
Libavfilter will try to pick one that is suitable as input to the next
filter.
It accepts the following parameters:
pix_fmts
A '|'-separated list of pixel format names, such as
"pix_fmts=yuv420p|monow|rgb24".
Some examples:
# Convert the input video to the "yuv420p" format
format=pix_fmts=yuv420p
# Convert the input video to any of the formats in the list
format=pix_fmts=yuv420p|yuv444p|yuv410p
fps
Convert the video to specified constant framerate by duplicating or
dropping frames as necessary.
It accepts the following parameters:
fps The desired output framerate.
start_time
Assume the first PTS should be the given value, in seconds. This
allows for padding/trimming at the start of stream. By default, no
assumption is made about the first frame's expected PTS, so no
padding or trimming is done. For example, this could be set to 0
to pad the beginning with duplicates of the first frame if a video
stream starts after the audio stream or to trim any frames with a
negative PTS.
framepack
Pack two different video streams into a stereoscopic video, setting
proper metadata on supported codecs. The two views should have the same
size and framerate and processing will stop when the shorter video
ends. Please note that you may conveniently adjust view properties with
the scale and fps filters.
It accepts the following parameters:
format
The desired packing format. Supported values are:
sbs The views are next to each other (default).
tab The views are on top of each other.
lines
The views are packed by line.
columns
The views are packed by column.
frameseq
The views are temporally interleaved.
Some examples:
# Convert left and right views into a frame-sequential video
avconv -i LEFT -i RIGHT -filter_complex framepack=frameseq OUTPUT
# Convert views into a side-by-side video with the same output resolution as the input
avconv -i LEFT -i RIGHT -filter_complex [0:v]scale=w=iw/2[left],[1:v]scale=w=iw/2[right],[left][right]framepack=sbs OUTPUT
frei0r
Apply a frei0r effect to the input video.
To enable the compilation of this filter, you need to install the
frei0r header and configure Libav with --enable-frei0r.
It accepts the following parameters:
filter_name
The name of the frei0r effect to load. If the environment variable
FREI0R_PATH is defined, the frei0r effect is searched for in each
of the directories specified by the colon-separated list in
FREIOR_PATH. Otherwise, the standard frei0r paths are searched, in
this order: HOME/.frei0r-1/lib/, /usr/local/lib/frei0r-1/,
/usr/lib/frei0r-1/.
filter_params
A '|'-separated list of parameters to pass to the frei0r effect.
A frei0r effect parameter can be a boolean (its value is either "y" or
"n"), a double, a color (specified as R/G/B, where R, G, and B are
floating point numbers between 0.0 and 1.0, inclusive) or by an
"av_parse_color()" color description), a position (specified as X/Y,
where X and Y are floating point numbers) and/or a string.
The number and types of parameters depend on the loaded effect. If an
effect parameter is not specified, the default value is set.
Some examples:
# Apply the distort0r effect, setting the first two double parameters
frei0r=filter_name=distort0r:filter_params=0.5|0.01
# Apply the colordistance effect, taking a color as the first parameter
frei0r=colordistance:0.2/0.3/0.4
frei0r=colordistance:violet
frei0r=colordistance:0x112233
# Apply the perspective effect, specifying the top left and top right
# image positions
frei0r=perspective:0.2/0.2|0.8/0.2
For more information, see <http://piksel.org/frei0r>
gradfun
Fix the banding artifacts that are sometimes introduced into nearly
flat regions by truncation to 8bit colordepth. Interpolate the
gradients that should go where the bands are, and dither them.
It is designed for playback only. Do not use it prior to lossy
compression, because compression tends to lose the dither and bring
back the bands.
It accepts the following parameters:
strength
The maximum amount by which the filter will change any one pixel.
This is also the threshold for detecting nearly flat regions.
Acceptable values range from .51 to 64; the default value is 1.2.
Out-of-range values will be clipped to the valid range.
radius
The neighborhood to fit the gradient to. A larger radius makes for
smoother gradients, but also prevents the filter from modifying the
pixels near detailed regions. Acceptable values are 8-32; the
default value is 16. Out-of-range values will be clipped to the
valid range.
# Default parameters
gradfun=strength=1.2:radius=16
# Omitting the radius
gradfun=1.2
hflip
Flip the input video horizontally.
For example, to horizontally flip the input video with avconv:
avconv -i in.avi -vf "hflip" out.avi
hqdn3d
This is a high precision/quality 3d denoise filter. It aims to reduce
image noise, producing smooth images and making still images really
still. It should enhance compressibility.
It accepts the following optional parameters:
luma_spatial
A non-negative floating point number which specifies spatial luma
strength. It defaults to 4.0.
chroma_spatial
A non-negative floating point number which specifies spatial chroma
strength. It defaults to 3.0*luma_spatial/4.0.
luma_tmp
A floating point number which specifies luma temporal strength. It
defaults to 6.0*luma_spatial/4.0.
chroma_tmp
A floating point number which specifies chroma temporal strength.
It defaults to luma_tmp*chroma_spatial/luma_spatial.
interlace
Simple interlacing filter from progressive contents. This interleaves
upper (or lower) lines from odd frames with lower (or upper) lines from
even frames, halving the frame rate and preserving image height.
Original Original New Frame
Frame 'j' Frame 'j+1' (tff)
========== =========== ==================
Line 0 --------------------> Frame 'j' Line 0
Line 1 Line 1 ----> Frame 'j+1' Line 1
Line 2 ---------------------> Frame 'j' Line 2
Line 3 Line 3 ----> Frame 'j+1' Line 3
... ... ...
New Frame + 1 will be generated by Frame 'j+2' and Frame 'j+3' and so on
It accepts the following optional parameters:
scan
This determines whether the interlaced frame is taken from the even
(tff - default) or odd (bff) lines of the progressive frame.
lowpass
Enable (default) or disable the vertical lowpass filter to avoid
twitter interlacing and reduce moire patterns.
lut, lutrgb, lutyuv
Compute a look-up table for binding each pixel component input value to
an output value, and apply it to the input video.
lutyuv applies a lookup table to a YUV input video, lutrgb to an RGB
input video.
These filters accept the following parameters:
c0 (first pixel component)
c1 (second pixel component)
c2 (third pixel component)
c3 (fourth pixel component, corresponds to the alpha component)
r (red component)
g (green component)
b (blue component)
a (alpha component)
y (Y/luminance component)
u (U/Cb component)
v (V/Cr component)
Each of them specifies the expression to use for computing the lookup
table for the corresponding pixel component values.
The exact component associated to each of the c* options depends on the
format in input.
The lut filter requires either YUV or RGB pixel formats in input,
lutrgb requires RGB pixel formats in input, and lutyuv requires YUV.
The expressions can contain the following constants and functions:
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
w, h
The input width and height.
val The input value for the pixel component.
clipval
The input value, clipped to the minval-maxval range.
maxval
The maximum value for the pixel component.
minval
The minimum value for the pixel component.
negval
The negated value for the pixel component value, clipped to the
minval-maxval range; it corresponds to the expression
"maxval-clipval+minval".
clip(val)
The computed value in val, clipped to the minval-maxval range.
gammaval(gamma)
The computed gamma correction value of the pixel component value,
clipped to the minval-maxval range. It corresponds to the
expression
"pow((clipval-minval)/(maxval-minval),gamma)*(maxval-minval)+minval"
All expressions default to "val".
Some examples:
# Negate input video
lutrgb="r=maxval+minval-val:g=maxval+minval-val:b=maxval+minval-val"
lutyuv="y=maxval+minval-val:u=maxval+minval-val:v=maxval+minval-val"
# The above is the same as
lutrgb="r=negval:g=negval:b=negval"
lutyuv="y=negval:u=negval:v=negval"
# Negate luminance
lutyuv=negval
# Remove chroma components, turning the video into a graytone image
lutyuv="u=128:v=128"
# Apply a luma burning effect
lutyuv="y=2*val"
# Remove green and blue components
lutrgb="g=0:b=0"
# Set a constant alpha channel value on input
format=rgba,lutrgb=a="maxval-minval/2"
# Correct luminance gamma by a factor of 0.5
lutyuv=y=gammaval(0.5)
negate
Negate input video.
It accepts an integer in input; if non-zero it negates the alpha
component (if available). The default value in input is 0.
noformat
Force libavfilter not to use any of the specified pixel formats for the
input to the next filter.
It accepts the following parameters:
pix_fmts
A '|'-separated list of pixel format names, such as
apix_fmts=yuv420p|monow|rgb24".
Some examples:
# Force libavfilter to use a format different from "yuv420p" for the
# input to the vflip filter
noformat=pix_fmts=yuv420p,vflip
# Convert the input video to any of the formats not contained in the list
noformat=yuv420p|yuv444p|yuv410p
null
Pass the video source unchanged to the output.
ocv
Apply a video transform using libopencv.
To enable this filter, install the libopencv library and headers and
configure Libav with --enable-libopencv.
It accepts the following parameters:
filter_name
The name of the libopencv filter to apply.
filter_params
The parameters to pass to the libopencv filter. If not specified,
the default values are assumed.
Refer to the official libopencv documentation for more precise
information:
<http://opencv.willowgarage.com/documentation/c/image_filtering.html>
Several libopencv filters are supported; see the following subsections.
dilate
Dilate an image by using a specific structuring element. It
corresponds to the libopencv function "cvDilate".
It accepts the parameters: struct_el|nb_iterations.
struct_el represents a structuring element, and has the syntax:
colsxrows+anchor_xxanchor_y/shape
cols and rows represent the number of columns and rows of the
structuring element, anchor_x and anchor_y the anchor point, and shape
the shape for the structuring element. shape must be "rect", "cross",
"ellipse", or "custom".
If the value for shape is "custom", it must be followed by a string of
the form "=filename". The file with name filename is assumed to
represent a binary image, with each printable character corresponding
to a bright pixel. When a custom shape is used, cols and rows are
ignored, the number or columns and rows of the read file are assumed
instead.
The default value for struct_el is "3x3+0x0/rect".
nb_iterations specifies the number of times the transform is applied to
the image, and defaults to 1.
Some examples:
# Use the default values
ocv=dilate
# Dilate using a structuring element with a 5x5 cross, iterating two times
ocv=filter_name=dilate:filter_params=5x5+2x2/cross|2
# Read the shape from the file diamond.shape, iterating two times.
# The file diamond.shape may contain a pattern of characters like this
# *
# ***
# *****
# ***
# *
# The specified columns and rows are ignored
# but the anchor point coordinates are not
ocv=dilate:0x0+2x2/custom=diamond.shape|2
erode
Erode an image by using a specific structuring element. It corresponds
to the libopencv function "cvErode".
It accepts the parameters: struct_el:nb_iterations, with the same
syntax and semantics as the dilate filter.
smooth
Smooth the input video.
The filter takes the following parameters:
type|param1|param2|param3|param4.
type is the type of smooth filter to apply, and must be one of the
following values: "blur", "blur_no_scale", "median", "gaussian", or
"bilateral". The default value is "gaussian".
The meaning of param1, param2, param3, and param4 depend on the smooth
type. param1 and param2 accept integer positive values or 0. param3 and
param4 accept floating point values.
The default value for param1 is 3. The default value for the other
parameters is 0.
These parameters correspond to the parameters assigned to the libopencv
function "cvSmooth".
overlay
Overlay one video on top of another.
It takes two inputs and has one output. The first input is the "main"
video on which the second input is overlayed.
It accepts the following parameters:
x The horizontal position of the left edge of the overlaid video on
the main video.
y The vertical position of the top edge of the overlaid video on the
main video.
The parameters are expressions containing the following parameters:
main_w, main_h
The main input width and height.
W, H
These are the same as main_w and main_h.
overlay_w, overlay_h
The overlay input width and height.
w, h
These are the same as overlay_w and overlay_h.
eof_action
The action to take when EOF is encountered on the secondary input;
it accepts one of the following values:
repeat
Repeat the last frame (the default).
endall
End both streams.
pass
Pass the main input through.
Be aware that frames are taken from each input video in timestamp
order, hence, if their initial timestamps differ, it is a a good idea
to pass the two inputs through a setpts=PTS-STARTPTS filter to have
them begin in the same zero timestamp, as the example for the movie
filter does.
Some examples:
# Draw the overlay at 10 pixels from the bottom right
# corner of the main video
overlay=x=main_w-overlay_w-10:y=main_h-overlay_h-10
# Insert a transparent PNG logo in the bottom left corner of the input
avconv -i input -i logo -filter_complex 'overlay=x=10:y=main_h-overlay_h-10' output
# Insert 2 different transparent PNG logos (second logo on bottom
# right corner)
avconv -i input -i logo1 -i logo2 -filter_complex
'overlay=x=10:y=H-h-10,overlay=x=W-w-10:y=H-h-10' output
# Add a transparent color layer on top of the main video;
# WxH specifies the size of the main input to the overlay filter
color=red.3:WxH [over]; [in][over] overlay [out]
# Mask 10-20 seconds of a video by applying the delogo filter to a section
avconv -i test.avi -codec:v:0 wmv2 -ar 11025 -b:v 9000k
-vf '[in]split[split_main][split_delogo];[split_delogo]trim=start=360:end=371,delogo=0:0:640:480[delogoed];[split_main][delogoed]overlay=eof_action=pass[out]'
masked.avi
You can chain together more overlays but the efficiency of such
approach is yet to be tested.
pad
Add paddings to the input image, and place the original input at the
provided x, y coordinates.
It accepts the following parameters:
width, height
Specify the size of the output image with the paddings added. If
the value for width or height is 0, the corresponding input size is
used for the output.
The width expression can reference the value set by the height
expression, and vice versa.
The default value of width and height is 0.
x, y
Specify the offsets to place the input image at within the padded
area, with respect to the top/left border of the output image.
The x expression can reference the value set by the y expression,
and vice versa.
The default value of x and y is 0.
color
Specify the color of the padded area. It can be the name of a color
(case insensitive match) or an 0xRRGGBB[AA] sequence.
The default value of color is "black".
The parameters width, height, x, and y are expressions containing the
following constants:
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
in_w, in_h
The input video width and height.
iw, ih
These are the same as in_w and in_h.
out_w, out_h
The output width and height (the size of the padded area), as
specified by the width and height expressions.
ow, oh
These are the same as out_w and out_h.
x, y
The x and y offsets as specified by the x and y expressions, or NAN
if not yet specified.
a The input display aspect ratio, same as iw / ih.
hsub, vsub
The horizontal and vertical chroma subsample values. For example
for the pixel format "yuv422p" hsub is 2 and vsub is 1.
Some examples:
# Add paddings with the color "violet" to the input video. The output video
# size is 640x480, and the top-left corner of the input video is placed at
# column 0, row 40
pad=width=640:height=480:x=0:y=40:color=violet
# Pad the input to get an output with dimensions increased by 3/2,
# and put the input video at the center of the padded area
pad="3/2*iw:3/2*ih:(ow-iw)/2:(oh-ih)/2"
# Pad the input to get a squared output with size equal to the maximum
# value between the input width and height, and put the input video at
# the center of the padded area
pad="max(iw,ih):ow:(ow-iw)/2:(oh-ih)/2"
# Pad the input to get a final w/h ratio of 16:9
pad="ih*16/9:ih:(ow-iw)/2:(oh-ih)/2"
# Double the output size and put the input video in the bottom-right
# corner of the output padded area
pad="2*iw:2*ih:ow-iw:oh-ih"
pixdesctest
Pixel format descriptor test filter, mainly useful for internal
testing. The output video should be equal to the input video.
For example:
format=monow, pixdesctest
can be used to test the monowhite pixel format descriptor definition.
scale
Scale the input video and/or convert the image format.
It accepts the following parameters:
w The output video width.
h The output video height.
The parameters w and h are expressions containing the following
constants:
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
in_w, in_h
The input width and height.
iw, ih
These are the same as in_w and in_h.
out_w, out_h
The output (cropped) width and height.
ow, oh
These are the same as out_w and out_h.
a This is the same as iw / ih.
sar input sample aspect ratio
dar The input display aspect ratio; it is the same as (iw / ih) * sar.
hsub, vsub
The horizontal and vertical chroma subsample values. For example,
for the pixel format "yuv422p" hsub is 2 and vsub is 1.
If the input image format is different from the format requested by the
next filter, the scale filter will convert the input to the requested
format.
If the value for w or h is 0, the respective input size is used for the
output.
If the value for w or h is -1, the scale filter will use, for the
respective output size, a value that maintains the aspect ratio of the
input image.
The default value of w and h is 0.
Some examples:
# Scale the input video to a size of 200x100
scale=w=200:h=100
# Scale the input to 2x
scale=w=2*iw:h=2*ih
# The above is the same as
scale=2*in_w:2*in_h
# Scale the input to half the original size
scale=w=iw/2:h=ih/2
# Increase the width, and set the height to the same size
scale=3/2*iw:ow
# Seek Greek harmony
scale=iw:1/PHI*iw
scale=ih*PHI:ih
# Increase the height, and set the width to 3/2 of the height
scale=w=3/2*oh:h=3/5*ih
# Increase the size, making the size a multiple of the chroma
scale="trunc(3/2*iw/hsub)*hsub:trunc(3/2*ih/vsub)*vsub"
# Increase the width to a maximum of 500 pixels,
# keeping the same aspect ratio as the input
scale=w='min(500, iw*3/2):h=-1'
select
Select frames to pass in output.
It accepts the following parameters:
expr
An expression, which is evaluated for each input frame. If the
expression is evaluated to a non-zero value, the frame is selected
and passed to the output, otherwise it is discarded.
The expression can contain the following constants:
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
n The (sequential) number of the filtered frame, starting from 0.
selected_n
The (sequential) number of the selected frame, starting from 0.
prev_selected_n
The sequential number of the last selected frame. It's NAN if
undefined.
TB The timebase of the input timestamps.
pts The PTS (Presentation TimeStamp) of the filtered video frame,
expressed in TB units. It's NAN if undefined.
t The PTS of the filtered video frame, expressed in seconds. It's NAN
if undefined.
prev_pts
The PTS of the previously filtered video frame. It's NAN if
undefined.
prev_selected_pts
The PTS of the last previously filtered video frame. It's NAN if
undefined.
prev_selected_t
The PTS of the last previously selected video frame. It's NAN if
undefined.
start_pts
The PTS of the first video frame in the video. It's NAN if
undefined.
start_t
The time of the first video frame in the video. It's NAN if
undefined.
pict_type
The type of the filtered frame. It can assume one of the following
values:
I
P
B
S
SI
SP
BI
interlace_type
The frame interlace type. It can assume one of the following
values:
PROGRESSIVE
The frame is progressive (not interlaced).
TOPFIRST
The frame is top-field-first.
BOTTOMFIRST
The frame is bottom-field-first.
key This is 1 if the filtered frame is a key-frame, 0 otherwise.
The default value of the select expression is "1".
Some examples:
# Select all the frames in input
select
# The above is the same as
select=expr=1
# Skip all frames
select=expr=0
# Select only I-frames
select='expr=eq(pict_type,I)'
# Select one frame per 100
select='not(mod(n,100))'
# Select only frames contained in the 10-20 time interval
select='gte(t,10)*lte(t,20)'
# Select only I frames contained in the 10-20 time interval
select='gte(t,10)*lte(t,20)*eq(pict_type,I)'
# Select frames with a minimum distance of 10 seconds
select='isnan(prev_selected_t)+gte(t-prev_selected_t,10)'
setdar
Set the Display Aspect Ratio for the filter output video.
This is done by changing the specified Sample (aka Pixel) Aspect Ratio,
according to the following equation: DAR = HORIZONTAL_RESOLUTION /
VERTICAL_RESOLUTION * SAR
Keep in mind that this filter does not modify the pixel dimensions of
the video frame. Also, the display aspect ratio set by this filter may
be changed by later filters in the filterchain, e.g. in case of scaling
or if another "setdar" or a "setsar" filter is applied.
It accepts the following parameters:
dar The output display aspect ratio.
The parameter dar is an expression containing the following constants:
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
w, h
The input width and height.
a This is the same as w / h.
sar The input sample aspect ratio.
dar The input display aspect ratio. It is the same as (w / h) * sar.
hsub, vsub
The horizontal and vertical chroma subsample values. For example,
for the pixel format "yuv422p" hsub is 2 and vsub is 1.
To change the display aspect ratio to 16:9, specify:
setdar=dar=16/9
# The above is equivalent to
setdar=dar=1.77777
Also see the the setsar filter documentation.
setpts
Change the PTS (presentation timestamp) of the input video frames.
It accepts the following parameters:
expr
The expression which is evaluated for each frame to construct its
timestamp.
The expression is evaluated through the eval API and can contain the
following constants:
PTS The presentation timestamp in input.
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
N The count of the input frame, starting from 0.
STARTPTS
The PTS of the first video frame.
INTERLACED
State whether the current frame is interlaced.
PREV_INPTS
The previous input PTS.
PREV_OUTPTS
The previous output PTS.
RTCTIME
The wallclock (RTC) time in microseconds.
RTCSTART
The wallclock (RTC) time at the start of the movie in microseconds.
TB The timebase of the input timestamps.
Some examples:
# Start counting the PTS from zero
setpts=expr=PTS-STARTPTS
# Fast motion
setpts=expr=0.5*PTS
# Slow motion
setpts=2.0*PTS
# Fixed rate 25 fps
setpts=N/(25*TB)
# Fixed rate 25 fps with some jitter
setpts='1/(25*TB) * (N + 0.05 * sin(N*2*PI/25))'
# Generate timestamps from a "live source" and rebase onto the current timebase
setpts='(RTCTIME - RTCSTART) / (TB * 1000000)"
setsar
Set the Sample (aka Pixel) Aspect Ratio for the filter output video.
Note that as a consequence of the application of this filter, the
output display aspect ratio will change according to the following
equation: DAR = HORIZONTAL_RESOLUTION / VERTICAL_RESOLUTION * SAR
Keep in mind that the sample aspect ratio set by this filter may be
changed by later filters in the filterchain, e.g. if another "setsar"
or a "setdar" filter is applied.
It accepts the following parameters:
sar The output sample aspect ratio.
The parameter sar is an expression containing the following constants:
E, PI, PHI
These are approximated values for the mathematical constants e
(Euler's number), pi (Greek pi), and phi (the golden ratio).
w, h
The input width and height.
a These are the same as w / h.
sar The input sample aspect ratio.
dar The input display aspect ratio. It is the same as (w / h) * sar.
hsub, vsub
Horizontal and vertical chroma subsample values. For example, for
the pixel format "yuv422p" hsub is 2 and vsub is 1.
To change the sample aspect ratio to 10:11, specify:
setsar=sar=10/11
settb
Set the timebase to use for the output frames timestamps. It is mainly
useful for testing timebase configuration.
It accepts the following parameters:
expr
The expression which is evaluated into the output timebase.
The expression can contain the constants "PI", "E", "PHI", "AVTB" (the
default timebase), and "intb" (the input timebase).
The default value for the input is "intb".
Some examples:
# Set the timebase to 1/25
settb=expr=1/25
# Set the timebase to 1/10
settb=expr=0.1
# Set the timebase to 1001/1000
settb=1+0.001
#Set the timebase to 2*intb
settb=2*intb
#Set the default timebase value
settb=AVTB
showinfo
Show a line containing various information for each input video frame.
The input video is not modified.
The shown line contains a sequence of key/value pairs of the form
key:value.
It accepts the following parameters:
n The (sequential) number of the input frame, starting from 0.
pts The Presentation TimeStamp of the input frame, expressed as a
number of time base units. The time base unit depends on the filter
input pad.
pts_time
The Presentation TimeStamp of the input frame, expressed as a
number of seconds.
pos The position of the frame in the input stream, or -1 if this
information is unavailable and/or meaningless (for example in case
of synthetic video).
fmt The pixel format name.
sar The sample aspect ratio of the input frame, expressed in the form
num/den.
s The size of the input frame, expressed in the form widthxheight.
i The type of interlaced mode ("P" for "progressive", "T" for top
field first, "B" for bottom field first).
iskey
This is 1 if the frame is a key frame, 0 otherwise.
type
The picture type of the input frame ("I" for an I-frame, "P" for a
P-frame, "B" for a B-frame, or "?" for an unknown type). Also
refer to the documentation of the "AVPictureType" enum and of the
"av_get_picture_type_char" function defined in libavutil/avutil.h.
checksum
The Adler-32 checksum of all the planes of the input frame.
plane_checksum
The Adler-32 checksum of each plane of the input frame, expressed
in the form "[c0 c1 c2 c3]".
shuffleplanes
Reorder and/or duplicate video planes.
It accepts the following parameters:
map0
The index of the input plane to be used as the first output plane.
map1
The index of the input plane to be used as the second output plane.
map2
The index of the input plane to be used as the third output plane.
map3
The index of the input plane to be used as the fourth output plane.
The first plane has the index 0. The default is to keep the input
unchanged.
Swap the second and third planes of the input:
avconv -i INPUT -vf shuffleplanes=0:2:1:3 OUTPUT
split
Split input video into several identical outputs.
It accepts a single parameter, which specifies the number of outputs.
If unspecified, it defaults to 2.
Create 5 copies of the input video:
avconv -i INPUT -filter_complex split=5 OUTPUT
transpose
Transpose rows with columns in the input video and optionally flip it.
It accepts the following parameters:
dir The direction of the transpose.
The direction can assume the following values:
cclock_flip
Rotate by 90 degrees counterclockwise and vertically flip
(default), that is:
L.R L.l
. . -> . .
l.r R.r
clock
Rotate by 90 degrees clockwise, that is:
L.R l.L
. . -> . .
l.r r.R
cclock
Rotate by 90 degrees counterclockwise, that is:
L.R R.r
. . -> . .
l.r L.l
clock_flip
Rotate by 90 degrees clockwise and vertically flip, that is:
L.R r.R
. . -> . .
l.r l.L
trim
Trim the input so that the output contains one continuous subpart of
the input.
It accepts the following parameters:
start
The timestamp (in seconds) of the start of the kept section. The
frame with the timestamp start will be the first frame in the
output.
end The timestamp (in seconds) of the first frame that will be dropped.
The frame immediately preceding the one with the timestamp end will
be the last frame in the output.
start_pts
This is the same as start, except this option sets the start
timestamp in timebase units instead of seconds.
end_pts
This is the same as end, except this option sets the end timestamp
in timebase units instead of seconds.
duration
The maximum duration of the output in seconds.
start_frame
The number of the first frame that should be passed to the output.
end_frame
The number of the first frame that should be dropped.
Note that the first two sets of the start/end options and the duration
option look at the frame timestamp, while the _frame variants simply
count the frames that pass through the filter. Also note that this
filter does not modify the timestamps. If you wish for the output
timestamps to start at zero, insert a setpts filter after the trim
filter.
If multiple start or end options are set, this filter tries to be
greedy and keep all the frames that match at least one of the specified
constraints. To keep only the part that matches all the constraints at
once, chain multiple trim filters.
The defaults are such that all the input is kept. So it is possible to
set e.g. just the end values to keep everything before the specified
time.
Examples:
o Drop everything except the second minute of input:
avconv -i INPUT -vf trim=60:120
o Keep only the first second:
avconv -i INPUT -vf trim=duration=1
unsharp
Sharpen or blur the input video.
It accepts the following parameters:
luma_msize_x
Set the luma matrix horizontal size. It must be an integer between
3 and 13. The default value is 5.
luma_msize_y
Set the luma matrix vertical size. It must be an integer between 3
and 13. The default value is 5.
luma_amount
Set the luma effect strength. It must be a floating point number
between -2.0 and 5.0. The default value is 1.0.
chroma_msize_x
Set the chroma matrix horizontal size. It must be an integer
between 3 and 13. The default value is 5.
chroma_msize_y
Set the chroma matrix vertical size. It must be an integer between
3 and 13. The default value is 5.
chroma_amount
Set the chroma effect strength. It must be a floating point number
between -2.0 and 5.0. The default value is 0.0.
Negative values for the amount will blur the input video, while
positive values will sharpen. All parameters are optional and default
to the equivalent of the string '5:5:1.0:5:5:0.0'.
# Strong luma sharpen effect parameters
unsharp=luma_msize_x=7:luma_msize_y=7:luma_amount=2.5
# A strong blur of both luma and chroma parameters
unsharp=7:7:-2:7:7:-2
# Use the default values with B<avconv>
./avconv -i in.avi -vf "unsharp" out.mp4
vflip
Flip the input video vertically.
./avconv -i in.avi -vf "vflip" out.avi
yadif
Deinterlace the input video ("yadif" means "yet another deinterlacing
filter").
It accepts the following parameters:
mode
The interlacing mode to adopt. It accepts one of the following
values:
0 Output one frame for each frame.
1 Output one frame for each field.
2 Like 0, but it skips the spatial interlacing check.
3 Like 1, but it skips the spatial interlacing check.
The default value is 0.
parity
The picture field parity assumed for the input interlaced video. It
accepts one of the following values:
0 Assume the top field is first.
1 Assume the bottom field is first.
-1 Enable automatic detection of field parity.
The default value is -1. If the interlacing is unknown or the
decoder does not export this information, top field first will be
assumed.
auto
Whether the deinterlacer should trust the interlaced flag and only
deinterlace frames marked as interlaced.
0 Deinterlace all frames.
1 Only deinterlace frames marked as interlaced.
The default value is 0.
Below is a description of the currently available video sources.
buffer
Buffer video frames, and make them available to the filter chain.
This source is mainly intended for a programmatic use, in particular
through the interface defined in libavfilter/vsrc_buffer.h.
It accepts the following parameters:
width
The input video width.
height
The input video height.
pix_fmt
The name of the input video pixel format.
time_base
The time base used for input timestamps.
sar The sample (pixel) aspect ratio of the input video.
For example:
buffer=width=320:height=240:pix_fmt=yuv410p:time_base=1/24:sar=1
will instruct the source to accept video frames with size 320x240 and
with format "yuv410p", assuming 1/24 as the timestamps timebase and
square pixels (1:1 sample aspect ratio).
color
Provide an uniformly colored input.
It accepts the following parameters:
color
Specify the color of the source. It can be the name of a color
(case insensitive match) or a 0xRRGGBB[AA] sequence, possibly
followed by an alpha specifier. The default value is "black".
size
Specify the size of the sourced video, it may be a string of the
form widthxheight, or the name of a size abbreviation. The default
value is "320x240".
framerate
Specify the frame rate of the sourced video, as the number of
frames generated per second. It has to be a string in the format
frame_rate_num/frame_rate_den, an integer number, a floating point
number or a valid video frame rate abbreviation. The default value
is "25".
The following graph description will generate a red source with an
opacity of 0.2, with size "qcif" and a frame rate of 10 frames per
second, which will be overlayed over the source connected to the pad
with identifier "in":
"color=red@0.2:qcif:10 [color]; [in][color] overlay [out]"
movie
Read a video stream from a movie container.
Note that this source is a hack that bypasses the standard input path.
It can be useful in applications that do not support arbitrary filter
graphs, but its use is discouraged in those that do. It should never be
used with avconv; the -filter_complex option fully replaces it.
It accepts the following parameters:
filename
The name of the resource to read (not necessarily a file; it can
also be a device or a stream accessed through some protocol).
format_name, f
Specifies the format assumed for the movie to read, and can be
either the name of a container or an input device. If not
specified, the format is guessed from movie_name or by probing.
seek_point, sp
Specifies the seek point in seconds. The frames will be output
starting from this seek point. The parameter is evaluated with
"av_strtod", so the numerical value may be suffixed by an IS
postfix. The default value is "0".
stream_index, si
Specifies the index of the video stream to read. If the value is
-1, the most suitable video stream will be automatically selected.
The default value is "-1".
It allows overlaying a second video on top of the main input of a
filtergraph, as shown in this graph:
input -----------> deltapts0 --> overlay --> output
^
|
movie --> scale--> deltapts1 -------+
Some examples:
# Skip 3.2 seconds from the start of the AVI file in.avi, and overlay it
# on top of the input labelled "in"
movie=in.avi:seek_point=3.2, scale=180:-1, setpts=PTS-STARTPTS [movie];
[in] setpts=PTS-STARTPTS, [movie] overlay=16:16 [out]
# Read from a video4linux2 device, and overlay it on top of the input
# labelled "in"
movie=/dev/video0:f=video4linux2, scale=180:-1, setpts=PTS-STARTPTS [movie];
[in] setpts=PTS-STARTPTS, [movie] overlay=16:16 [out]
nullsrc
Null video source: never return images. It is mainly useful as a
template and to be employed in analysis / debugging tools.
It accepts a string of the form width:height:timebase as an optional
parameter.
width and height specify the size of the configured source. The default
values of width and height are respectively 352 and 288 (corresponding
to the CIF size format).
timebase specifies an arithmetic expression representing a timebase.
The expression can contain the constants "PI", "E", "PHI", and "AVTB"
(the default timebase), and defaults to the value "AVTB".
frei0r_src
Provide a frei0r source.
To enable compilation of this filter you need to install the frei0r
header and configure Libav with --enable-frei0r.
This source accepts the following parameters:
size
The size of the video to generate. It may be a string of the form
widthxheight or a frame size abbreviation.
framerate
The framerate of the generated video. It may be a string of the
form num/den or a frame rate abbreviation.
filter_name
The name to the frei0r source to load. For more information
regarding frei0r and how to set the parameters, read the frei0r
section in the video filters documentation.
filter_params
A '|'-separated list of parameters to pass to the frei0r source.
An example:
# Generate a frei0r partik0l source with size 200x200 and framerate 10
# which is overlayed on the overlay filter main input
frei0r_src=size=200x200:framerate=10:filter_name=partik0l:filter_params=1234 [overlay]; [in][overlay] overlay
rgbtestsrc, testsrc
The "rgbtestsrc" source generates an RGB test pattern useful for
detecting RGB vs BGR issues. You should see a red, green and blue
stripe from top to bottom.
The "testsrc" source generates a test video pattern, showing a color
pattern, a scrolling gradient and a timestamp. This is mainly intended
for testing purposes.
The sources accept the following parameters:
size, s
Specify the size of the sourced video, it may be a string of the
form widthxheight, or the name of a size abbreviation. The default
value is "320x240".
rate, r
Specify the frame rate of the sourced video, as the number of
frames generated per second. It has to be a string in the format
frame_rate_num/frame_rate_den, an integer number, a floating point
number or a valid video frame rate abbreviation. The default value
is "25".
sar Set the sample aspect ratio of the sourced video.
duration
Set the video duration of the sourced video. The accepted syntax
is:
[-]HH[:MM[:SS[.m...]]]
[-]S+[.m...]
Also see the the "av_parse_time()" function.
If not specified, or the expressed duration is negative, the video
is supposed to be generated forever.
For example the following:
testsrc=duration=5.3:size=qcif:rate=10
will generate a video with a duration of 5.3 seconds, with size 176x144
and a framerate of 10 frames per second.
Below is a description of the currently available video sinks.
buffersink
Buffer video frames, and make them available to the end of the filter
graph.
This sink is intended for programmatic use through the interface
defined in libavfilter/buffersink.h.
nullsink
Null video sink: do absolutely nothing with the input video. It is
mainly useful as a template and for use in analysis / debugging tools.
Libav is able to dump metadata from media files into a simple
UTF-8-encoded INI-like text file and then load it back using the
metadata muxer/demuxer.
The file format is as follows:
1. A file consists of a header and a number of metadata tags divided
into sections, each on its own line.
2. The header is a ';FFMETADATA' string, followed by a version number
(now 1).
3. Metadata tags are of the form 'key=value'
4. Immediately after header follows global metadata
5. After global metadata there may be sections with
per-stream/per-chapter metadata.
6. A section starts with the section name in uppercase (i.e. STREAM or
CHAPTER) in brackets ('[', ']') and ends with next section or end
of file.
7. At the beginning of a chapter section there may be an optional
timebase to be used for start/end values. It must be in form
'TIMEBASE=num/den', where num and den are integers. If the timebase
is missing then start/end times are assumed to be in milliseconds.
Next a chapter section must contain chapter start and end times in
form 'START=num', 'END=num', where num is a positive integer.
8. Empty lines and lines starting with ';' or '#' are ignored.
9. Metadata keys or values containing special characters ('=', ';',
'#', '\' and a newline) must be escaped with a backslash '\'.
10. Note that whitespace in metadata (e.g. foo = bar) is considered to
be a part of the tag (in the example above key is 'foo ', value is
' bar').
A ffmetadata file might look like this:
;FFMETADATA1
title=bike\\shed
;this is a comment
artist=Libav troll team
[CHAPTER]
TIMEBASE=1/1000
START=0
#chapter ends at 0:01:00
END=60000
title=chapter \#1
[STREAM]
title=multi\
line
avplay(1), avprobe(1) and the Libav HTML documentation
The Libav developers
2016-02-19 AVCONV(1)