DragonFly On-Line Manual Pages
AMR(4) DragonFly Kernel Interfaces Manual AMR(4)
amr -- MegaRAID SCSI/ATA/SATA RAID driver
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
To compile in debugging code:
options AMR_DEBUG=x # x=3 is maximum verbosity
Alternatively, to load the driver as a module at boot time, place the
following line in loader.conf(5):
The amr driver provides support for LSI Logic MegaRAID SCSI, ATA and SATA
RAID controllers and legacy American Megatrends MegaRAID SCSI RAID con-
trollers, including models relabeled and sold by Dell and Hewlett-
LSI MegaRAID SAS controllers are supported by mfi(4) and mrsas(4) and
will not work with this driver.
Controllers supported by the amr driver include:
* MegaRAID SATA 150-4
* MegaRAID SATA 150-6
* MegaRAID SATA 300-4X
* MegaRAID SATA 300-8X
* MegaRAID SCSI 320-1E
* MegaRAID SCSI 320-2E
* MegaRAID SCSI 320-4E
* MegaRAID SCSI 320-0X
* MegaRAID SCSI 320-2X
* MegaRAID SCSI 320-4X
* MegaRAID SCSI 320-0
* MegaRAID SCSI 320-1
* MegaRAID SCSI 320-2
* MegaRAID SCSI 320-4
* MegaRAID Series 418
* MegaRAID i4 133 RAID
* MegaRAID Elite 1500 (Series 467)
* MegaRAID Elite 1600 (Series 493)
* MegaRAID Elite 1650 (Series 4xx)
* MegaRAID Enterprise 1200 (Series 428)
* MegaRAID Enterprise 1300 (Series 434)
* MegaRAID Enterprise 1400 (Series 438)
* MegaRAID Enterprise 1500 (Series 467)
* MegaRAID Enterprise 1600 (Series 471)
* MegaRAID Express 100 (Series 466WS)
* MegaRAID Express 200 (Series 466)
* MegaRAID Express 300 (Series 490)
* MegaRAID Express 500 (Series 475)
* Dell PERC
* Dell PERC 2/SC
* Dell PERC 2/DC
* Dell PERC 3/DCL
* Dell PERC 3/QC
* Dell PERC 4/DC
* Dell PERC 4/IM
* Dell PERC 4/SC
* Dell PERC 4/Di
* Dell PERC 4e/DC
* Dell PERC 4e/Di
* Dell PERC 4e/Si
* Dell PERC 4ei
* HP NetRAID-1/Si
* HP NetRAID-3/Si (D4943A)
* HP Embedded NetRAID
* Intel RAID Controller SRCS16
* Intel RAID Controller SRCU42X
Compiling with AAC_DEBUG will enable debug messages.
Driver initialisation/shutdown phase
amr%d: memory window not available
amr%d: I/O window not available
The PCI BIOS did not allocate resources necessary for the correct opera-
tion of the controller. The driver cannot attach to this controller.
amr%d: busmaster bit not set, enabling
The PCI BIOS did not enable busmaster DMA, which is required for the cor-
rect operation of the controller. The driver has enabled this bit and
initialisation will proceed.
amr%d: can't allocate register window
amr%d: can't allocate interrupt
amr%d: can't set up interrupt
amr%d: can't allocate parent DMA tag
amr%d: can't allocate buffer DMA tag
amr%d: can't allocate scatter/gather DMA tag
amr%d: can't allocate s/g table
amr%d: can't allocate mailbox tag
amr%d: can't allocate mailbox memory
A resource allocation error occurred while initialising the driver; ini-
tialisation has failed and the driver will not attach to this controller.
amr%d: can't obtain configuration data from controller
amr%d: can't obtain product data from controller
The driver was unable to obtain vital configuration data from the con-
troller. Initialisation has failed and the driver will not attach to
amr%d: can't establish configuration hook
amr%d: can't scan controller for drives
The scan for logical drives managed by the controller failed. No drives
will be attached.
amr%d: device_add_child failed
amr%d: bus_generic_attach returned %d
Creation of the logical drive instances failed; attachment of one or more
logical drives may have been aborted.
amr%d: flushing cache...
The controller cache is being flushed prior to shutdown or detach.
amr%d: I/O beyond end of unit (%u,%d > %u)
A partitioning error or disk corruption has caused an I/O request beyond
the end of the logical drive. This may also occur if FlexRAID Virtual
Sizing is enabled and an I/O operation is attempted on a portion of the
virtual drive beyond the actual capacity available.
amr%d: polled command timeout
An initialisation command timed out. The initialisation process may fail
as a result.
amr%d: bad slot %d completed
The controller reported completion of a command that the driver did not
issue. This may result in data corruption, and suggests a hardware or
firmware problem with the system or controller.
amr%d: I/O error - %x
An I/O error has occurred.
cd(4), da(4), mfi(4), mrsas(4), sa(4), scsi(4)
The amr driver was written by Mike Smith <msmith@FreeBSD.org>.
This manual page was written by Mike Smith <msmith@FreeBSD.org> and
Jeroen Ruigrok van der Werven <asmodai@FreeBSD.org>.
DragonFly 3.9 June 14, 2014 DragonFly 3.9