DragonFly On-Line Manual Pages
Smokeping_probes_OpenSSHEOSPing(3) SmokePing
NAME
Smokeping::probes::OpenSSHEOSPing - Arista EOS SSH Probe for SmokePing
SYNOPSIS
*** Probes ***
+OpenSSHEOSPing
forks = 5
offset = 50%
packetsize = 100
step = 300
timeout = 15
# The following variables can be overridden in each target section
eospass = password # mandatory
eosuser = user # mandatory
pings = 5
psource = 192.168.2.129
source = 192.168.2.1 # mandatory
unpriv = 1
# [...]
*** Targets ***
probe = OpenSSHEOSPing # if this should be the default probe
# [...]
+ mytarget
# probe = OpenSSHEOSPing # if the default probe is something else
host = my.host
eospass = password # mandatory
eosuser = user # mandatory
pings = 5
psource = 192.168.2.129
source = 192.168.2.1 # mandatory
unpriv = 1
DESCRIPTION
Connect to Arista EOS via OpenSSH to run ping commands. This probe
uses the "ping" cli of the Arista EOS. You have the option to specify
which interface the ping is sourced from as well.
VARIABLES
Supported probe-specific variables:
forks
Run this many concurrent processes at maximum
Example value: 5
Default value: 5
offset
If you run many probes concurrently you may want to prevent them
from hitting your network all at the same time. Using the probe-
specific offset parameter you can change the point in time when
each probe will be run. Offset is specified in % of total interval,
or alternatively as 'random', and the offset from the 'General'
section is used if nothing is specified here. Note that this does
NOT influence the rrds itself, it is just a matter of when data
acqusition is initiated. (This variable is only applicable if the
variable 'concurrentprobes' is set in the 'General' section.)
Example value: 50%
packetsize
The (optional) packetsize option lets you configure the packetsize
for the pings sent.
Default value: 100
step
Duration of the base interval that this probe should use, if
different from the one specified in the 'Database' section. Note
that the step in the RRD files is fixed when they are originally
generated, and if you change the step parameter afterwards, you'll
have to delete the old RRD files or somehow convert them. (This
variable is only applicable if the variable 'concurrentprobes' is
set in the 'General' section.)
Example value: 300
timeout
How long a single 'ping' takes at maximum
Example value: 15
Default value: 5
Supported target-specific variables:
eospass
The eospass option allows you to specify the password for the
username specified with the option eosuser.
Example value: password
This setting is mandatory.
eosuser
The eosuser option allows you to specify a username that has ping
capability on the EOS Device.
Example value: user
This setting is mandatory.
pings
How many pings should be sent to each target, if different from the
global value specified in the Database section. Note that the
number of pings in the RRD files is fixed when they are originally
generated, and if you change this parameter afterwards, you'll have
to delete the old RRD files or somehow convert them.
Example value: 5
psource
The (optional) psource option specifies an alternate IP address or
Interface from which you wish to source your pings from. Routers
can have many many IP addresses, and interfaces. When you ping
from a router you have the ability to choose which interface and/or
which IP address the ping is sourced from. Specifying an
IP/interface does not necessarily specify the interface from which
the ping will leave, but will specify which address the packet(s)
appear to come from. If this option is left out the EOS Device
will source the packet automatically based on routing and/or
metrics. If this doesn't make sense to you then just leave it out.
Example value: 192.168.2.129
source
The source option specifies the EOS device that is going to run the
ping commands. This address will be used for the ssh connection.
Example value: 192.168.2.1
This setting is mandatory.
unpriv
If the account is unprivileged, specify the 'unpriv' option. You
must also configure "pings = 5", since that is the only value
supported, and values specified for packetsize or psource are
ignored.
Example value: 1
AUTHORS
Bill Fenner <fenner@aristanetworks.com>
based on Smokeping::Probes::OpenSSHJunOSPing by Tobias Oetiker
<tobi@oetiker.ch>, which itself is based on
Smokeping::probes::TelnetJunOSPing by S H A N <shanali@yahoo.com>.
NOTES
EOS configuration
The EOS device should have a username/password configured, and the ssh
server must not be disabled.
Make sure to connect to the remote host once from the commmand line as
the user who is running smokeping. On the first connect ssh will ask to
add the new host to its known_hosts file. This will not happen
automatically so the script will fail to login until the ssh key of
your EOS box is in the known_hosts file.
Requirements
This module requires the Net::OpenSSH and IO::Pty perl modules.
2.6.11 2016-02-19
Smokeping_probes_OpenSSHEOSPing(3)